Tripp Lite SNMPWEBSOLO User manual

Installation and
Quick Start Guide
SNMP/Web Management
Accessory
Models: SNMPWEBSOLO & SNMPWEBSOLOHV
1111 W. 35th Street, Chicago, IL 60609 USA
www.tripplite.com/support
Read this manual carefully before installation. A separate User's Guide (PDF
format) is included on the CD-ROM bundled with the accessory. Refer to the
User's Guide for additional information about configuration and operation.
Installation 2
Features 11
Tech Support 12
Warranty 13
Русский 15
WARRANTY
REGISTRATION
Register online today for a
chance to win a FREE Tripp Lite
product! www.tripplite.com/warranty
201110124-93-3108.indb 1 11/3/2011 11:59:50 AM

2
This SNMP/Web Management Accessory allows users to operate compatible Tripp Lite
UPS Systems and Inverter/Chargers as manageable devices on the network,
accessible via Web browser, Network Management Station or telnet.
1 - Preparation
1-1 Confirm Package Contents: In addition to this manual, your package should
include the following:
• Configurationcable(73-1025)
• CD-ROMcontainingadditionaldocumentationandManagementInformation
Base(MIB)filesforusewithNetworkManagementSystems(nototherwise
required)
• StandardRS-232(DB9)serialcable
• 120VACAdapter*or230VACAdapter**
• Euro(Universal)toHybridE/FCEE7/7plugadapter**
• 12VDCcable**
  *ComeswithSNMPWEBSOLOonly.
  **ComeswithSNMPWEBSOLOHVonly.
1-2 Install UPS or Inverter/Charger: Install your UPS or Inverter/Charger and turn it
on before installing the Accessory.
1-3 Locate MAC Address: The12-digitMACaddress(000667xxxxxx)isattachedto
the underside of the Accessory.
1-4 Determine Network Installation Method: Ifyournetwork'sDHCPserverwill
assign a dynamic IP address to the Accessory automatically, proceed to
2 - Dynamic IP Address Assignment. If you will assign a static IP address to
the Accessory manually, proceed to 3 - Static IP Address Assignment. If you
are uncertain which method to use, contact your network administrator for
assistance before continuing the installation process.
Installation
201110124-93-3108.indb 2 11/3/2011 11:59:50 AM

3
Installation
2 - Dynamic IP Address Assignment
2-1 Connect Accessory to Power: (RefertoFigure1,Figure2aorFigure2bon
page5and6.)TherearetwowaystoconnecttheAccessorytopower:
• ConnecttheACAdapter AtotheAccessoryviatheportlabeled“DCPower”
Band plug the other end into an AC power source supported by a UPS
(Figure1)orInverter/Charger(Figure2a).
• Connectoneendofthe12VDCCable Ato the Accessory via the port
labeled“DCPower” Band connect the other end Idirectly to the Inverter/
Charger J. This feature is available on select models only.
Note: The Accessory must be plugged into a power source protected by a UPS or
Inverter/Charger in order to maintain communications during a power outage.
2-2 Connect Accessory to Device: (RefertoFigure1,Figure2aorFigure2bon
page5and6.)Usingthestandardserialcableprovided,connectoneendtothe
Accessoryportlabeled“UPS/APS” CandtheotherendtotheDB9serialport
on your UPS or Inverter/Charger D.
2-3 Connect Accessory to Network: Connect a standard Ethernet patch cable to
theRJ45EthernetportontheAccessory.Note: This port does not support PoE
(Power over Ethernet) applications. The Accessory will attempt to obtain an IP
addressviaDHCP.Thismaytakeaslongasseveralminutes,dependingonyour
network environment.
2-4 Discover IP Address: Contact your network administrator to determine which IP
addresshasbeenassignedtotheAccessorybytheDHCPserver.Thecardcan
beidentifiedontheDHCPserverbyreferringtoitsMACaddress(seeStep 1-3).
Youmaywishtorequestalong-termleaseperiodfortheIPaddress,depending
on your application. After you have discovered the IP address, proceed to
4 - Test and Configure. Note: The DHCP address is also displayed during boot-
up when connected to a computer through the configuration cable and a
terminal emulation program.
201110124-93-3108.indb 3 11/3/2011 11:59:50 AM

4
Installation
3 - Static IP Address Assignment/Terminal Menu
Configuration Settings
3-1 Determine IP Information: Before assigning a static IP address, you'll need to
know the IP address, gateway address and subnet mask. If you do not have this
information, contact your network administrator for assistance.
3-2 Configure Terminal Emulation Program: OpenaVT100-compatibleterminal
emulationprogram(suchastheHyperTerminalprogrambundledwithMicrosoft®
Windows®)onacomputerwithanavailableDB9
serial port. A notebook computer may be the
most convenient choice. Set the terminal
emulationprogramtousetheCOMport Athat
correspondstotheDB9serialport.Specifythe
parameters Brequired to communicate with the
Accessory terminal interface:
If the terminal emulation program supports multiple emulation modes, you may
alsoneedtospecifyVT100emulation C.
Bits per second: 9600
Databits: 8
Parity: None
Stop bits: 1
Flow control: None
A B C
201110124-93-3108.indb 4 11/3/2011 11:59:51 AM

5
Installation
3-3 Connect Accessory to Computer: Usetheincludedmini-DINtoDB9
configurationcable(partnumber73-1025)toconnecttheAccessorytothe
computer. The circular connector Eat one end of the cable attaches to the
8-pinmini-DINserialport(labeledCONFIG) FontheAccessory(Alignthe
connectorcarefullytoavoiddamagingthepins).TheDB9connector Gat the
other end of the cable connects to the computer’s serial port H.
INVERTER/CHARGER
INVERTER/CHARGER
AC POWER SOURCE
D
A
A
C
E
G
H
H
F
F
Figure 1
Figure 2A
B
C
D
B
E
G
201110124-93-3108.indb 5 11/3/2011 11:59:51 AM

6
Installation
3-4 Connect Accessory to Network: Connect a standard Ethernet patch cable to
theRJ45EthernetportontheAccessory.Note: This port does not support PoE
(Power over Ethernet) applications.
3-5 Connect Accessory to Power: (RefertoFigure1,Figure2aorFigure2b.)
There are two ways to connect the Accessory to power:
• ConnecttheACAdapter AtotheAccessoryviatheportlabeled“DCPower”
Band plug the other end into an AC power source supported by a UPS
(Figure1)orInverter/Charger(Figure2a).
• Connectoneendofthe12VDCCable Ato the Accessory via the port
labeled“DCPower” Band connect the other end Idirectly to the Inverter/
Charger J. This feature is available on select models only.
Note: The Accessory must be plugged into a power source protected by a UPS or
Inverter/Charger in order to maintain communications during a power outage.
3-6 Connect Accessory to Device: (RefertoFigure1,Figure2aorFigure2b.)
Using the standard serial cable provided, connect one end to the Accessory port
labeled“UPS/APS” CandtheotherendtotheDB9serialportonyourUPSor
Inverter/Charger D.
Figure 2B
INVERTER/CHARGER
A
I
J
E
G
H
F
B
C
D
201110124-93-3108.indb 6 11/3/2011 11:59:52 AM

7
Installation
3-7 Configure Accessory in Terminal Mode: Note: The Accessory must be
reinitialized by pressing the reset button (located between the "Link" and "Status"
descriptions under the RJ45 port on the Accessory), for 3 seconds. After the
brief message shown below, an initialization page should appear in the terminal
emulationprogram.Pressanykeyonthekeyboardwithin10secondstochange
theAccessory'ssettings(Ifthe10-secondperiodhaselapsed,youcanreinitialize
theAccessory).
Note: The following message will appear in the terminal startup menu:
IAM:Got AUTO-CONFIGURED IPv6 address FE80::4200:FF:FE01:8 on interface eth0:3
IPv6 is not currently supported. Tripp Lite is working on IPv6 for a future release.
Follow the sequence of responses below in order to assign an IP address to the
Accessory. The default terminal mode password is TrippLite. Sample IP settings
areshown-supplyyourownIPinformationwhenyouconfigureyourAccessory.
This card's hostname [ ]?
This card's domain [ ]?
Obtain IP settings automatically using
DHCP for Ethernet interface? [Y]
IP address? [10.2.0.98]
Subnet mask? [255.0.0.0]
Gateway address? [10.0.0.1]
DNS server 1? [10.0.0.5]
DNS server 2? [10.2.0.10]
This cards host name? [cornflakes]
This cards domain? [tlsoftwaredev.local]
SNMP Settings
Enable SNMP Community 0 [Y]? y
Choose a community privilege level:
0 - noAccess
1 - v1UserReadOnly
2 - v1UserReadWrite
3 - v2cUserReadOnly
4 - v2cUserReadWrite
Privilege Level [4]:
Community Name [tripplite]:
Allowable Address Range : [0.0.0.0]?
Allowable Address Mask : [0.0.0.0]?
Enable SNMP Community 1 [N]? n
Enable SNMP Community 2 [N]? n
Enable SNMP Community 3 [N]? n
Note: Default SNMP access is:
Community 0 enable with v2 read only
community public
Community 1 enable with v2 read/write
community tripplite
201110124-93-3108.indb 7 11/3/2011 11:59:52 AM

8
Additional Settings
Additional Ethernet Settings:
Installation
Enable SNTP? [N]
Enable http? [Y]
Port number? [80]
Enable https? [N]
Port number? [443]
Enable telnet? [Y]
Port number? [23]
Enable ssh? [Y]
Port number? [22]
Hardware Parameters:
Would you like to update the RTC date/time in GMT? [N]
Time Zone (0 is GMT-12, 6 is CST) :
Time Zone Offsets Supported
Western Hemisphere Eastern Hemisphere
Hour
Off-Set Location
Hour
Off-Set Location
0 Greenwich,England -1 Mid Europe/Africa
1 SEGreenland -2 E Europe, E Central Africa
2 AtlanticOcean -3 Moscow,Mid-East,EAfrica
3 GreenlandTime -4 NW Caspian Sea
4 Atlantic Time -5 Ural Mountains, Russia
5Eastern Standard Time -6 Almaty(AlmaATA),Russia
6Central Standard Time -7 W Mongolia
7Mountain Standard Time -8 China
8 Pacific Standard Time -9 Japan
9Alaska Time -10 Eastern Russia, Sydney, Australia
10 Hawaii -11 Kamchatskiy, E Russia
11 PacicOcean
+/-12 InternationalDateLine
Do you wish to configure the advanced settings [y/n]? [Y]
This interface must have a unique MAC address.
Ethernet MAC Address? [00:06:67:01:00:08]
DO NOT MODIFY UNLESS DIRECTED BY YOUR ADMINISTRATOR
Do you want to completely erase the file system? [N]
201110124-93-3108.indb 8 11/3/2011 11:59:52 AM

9
Installation
DO NOT MODIFY UNLESS DIRECTED BY TRIPP LITE TECHNICAL SUPPORT
Default Ethernet setting (0=Auto, 1=10 Half, 2=10 Full, 3=100 Half, 4=100
Full)? [Auto]
DO NOT MODIFY UNLESS DIRECTED BY YOUR ADMINISTRATOR
Youcanalsochangetherootpassword,real-timeclockandothersettings.
Tripp Lite recommends against changing the default settings unless you are an
advanced user with a specific purpose. After you have finished entering settings,
theAccessorywillsavechangestomemoryandreboot(thismaytakeseveral
minutes).AftertheAccessoryreboots,theinitializationpageshoulddisplaythe
new static IP settings.
3-8 Remove Configuration Cable: Remove the configuration cable that connects the
Accessory to the computer.
4 - Test and Configure
4-1 Test Network Connection: After an IP address has been assigned to the
Accessory, try to access it with a Web browser that supports frames, forms and
Java™.OpenaWebbrowseronacomputerconnectedtotheLANandenterthe
Accessory’s IP address. You should be prompted for a password. The user name
is admin and the default password is admin. After you enter the user name and
password, the PowerAlert Status page will appear in the browser window. For
more information about configuration and operation of the managed device, refer
totheUser'sGuide,includedontheCD-ROMbundledwiththeAccessory.
201110124-93-3108.indb 9 11/3/2011 11:59:52 AM

10
Installation
4-2 Default Shutdown Setting (UPS Only):Duringalossofutilitypower,the
AccessoryisconfiguredtoshutdowntheUPSsystem2minutesafteralow
battery signal is received from the UPS. This allows the UPS to provide the
maximumavailableruntimetoconnectedequipment.Ifyouwanttochangethe
default setting, follow these instructions:
1.FromtheinitialPowerAlertStatuspage,clicktheSettings button Aat the top
of the screen, then click the Events button Bthat appears at the left side of
the screen.
2.FromtheEvent Settings page, confirm that the Low Battery Shutdown Cbox
ischeckedandthenclicktheDetailsTab D,ordouble-clickthecheckedbox
toaccesstheSettingDetailspage.
3.FromtheDetailspage E, choose your preferred settings from the Settings
drop down menu Fand click the Save Changes button G.
Note for Network Management System Users Only: Two MIB files - Tripplite.mib
and RFC1628.mib - must be loaded on each Network Management Station that
will monitor the UPS system or Inverter/Charger via SNMP. The files are provided
on the CD-ROM included in the product package.
AB CD EF G
201110124-93-3108.indb 10 11/3/2011 11:59:52 AM