Tripp Lite SmartRack SRTH6UB User manual

1
Owner’s Manual
SmartRack®
Vertical Expansion Rack
Models: SRTH6UB, SRTH12UB
(Series Numbers: AG-0545, AG-0546)
1111 W. 35th Street, Chicago, IL 60609 USA • tripplite.com/support
Copyright © 2021 Tripp Lite. All rights reserved.
WARRANTY REGISTRATION
Register your product today and be
automatically entered to win an ISOBAR®
surge protector in our monthly drawing!
tripplite.com/warranty
Español 16 • Français 31 • Русский 46

2
Important Safety Instructions 3
Compatible Rack Enclosures 4
Feature Identification 5
Configuration 6
Ground Connection 6
Adding or Removing Front and 6
Rear Doors
Removing Door 6
Reversing Front Door 7
Adding or Removing Roof Panel 9
Adding or Removing Side Panels 10
Adjusting Mounting Rails and 11
Cable Management Rails
Equipment Installation 12
Installing or Removing Cage Nuts 12
Specifications 13
Storage and Service 14
Warranty and 15
Product Registration
Table of Contents

3
Important Safety Instructions
SAVE THESE INSTRUCTIONS
All sections of this manual contain instructions and warnings that should be followed during the installation and
use of the Vertical Expansion Rack as described in this manual. Read all instructions and warnings thoroughly
before attempting to move, install or use the Vertical Expansion Rack as described in this manual. Failure to
comply will create a risk of personal injury and property damage and may invalidate the warranty.
• Keep the enclosure in a controlled indoor environment, away from moisture, temperature extremes, flammable liquids and
gasses, conductive contaminants, dust and direct sunlight.
• Leave adequate space at the front and rear of the enclosure for proper ventilation. Do not block, cover or insert objects into
the external ventilation openings of the enclosure.
• The enclosure is extremely heavy. Use caution when handling the enclosure. Do not attempt to unpack, move or install it
unassisted. Use a mechanical device such as a forklift or pallet jack to move the enclosure in the shipping container.
• Do not place any object on the enclosure, especially containers of liquid, and do not attempt to stack the enclosures or
more than one height adjustment kit on top of the enclosure.
• Inspect the Vertical Expansion Rack’s contents for shipping damage. Do not use the Vertical Expansion Rack if it is
damaged.
• Leave the enclosure in the shipping container until it has been moved as close to the final installation location as possible.
• The Vertical Expansion Rack is intended to be installed on top of Tripp Lite SmartRack Rack Enclosure models that are
secured to the building structure for stability.
• This equipment is intended to be installed by skilled, qualified service personnel.
• Install the SmartRack Rack Enclosure and Vertical Expansion Rack in a structurally sound area with a level floor that is able
to bear the weight of the enclosure and all equipment that will be installed and/or equipment that will be installed nearby.
• Be sure to connect the enclosure to ground. See Ground Connection for more information.
• Use caution when cutting packing materials. The contents could be scratched, causing damage not covered by the warranty.
• Save all packing materials for later use. Repacking and shipping the enclosure without the original packing materials may
cause product damage that will void the warranty.
• Do not re-ship the enclosure with additional equipment unless the enclosure was shipped with a special shock pallet (“SP1”
models only). The combined weight of the enclosure and installed equipment must not exceed the load capacity of the
pallet. Tripp Lite is not responsible for any damage that occurs during re-shipment.
• Not for use when children are present.
• Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the
failure of the life support equipment or to significantly affect its safety or effectiveness is not recommended.
CAUTION
GROUND

4
Compatible Rack Enclosures
The SRTH6UB and SRTH12UB Vertical Expansion Racks are compatible with the Tripp Lite SmartRack Rack Enclosure models
shown below, including Agency Series AGAC7006, AGAC7454, AGAC7761, AG-00BE, AG-0324, AG-0325, AG-0534,
AG-0535, AG-0536:
Model
SR2400
SR25UB
SR25UB
SR25UB3
SR25UB3001
SR25UBEXP
SR25UBSP1
SR25UBSP1
SR42UB
SR42UB
SR42UB
SR42UB007
SR42UB1032
SR42UB3
SR42UB3002
SR42UBC
SR42UBC001
SR42UBCL
SR42UBCLSP1
Model
SR42UBEXP
SR42UBEXP001
SR42UBEXP002
SR42UBEXP003
SR42UBEXP004
SR42UBEXP1032
SR42UBEXPC001
SR42UBEXPND
SR42UBEXPND3
SR42UBEXPNDNR3
SR42UBG
SR42UBG001
SR42UBG3
SR42UBG3001
SR42UBKD
SR42UBND
SR42UBSFDKD
SR42UBSP1
SR45UB
Model
SR45UBEXP
SR45UBEXPND
SR45UBEXPNDNR3
SR45UBND
SR45UBSP1
SR48UB
SR48UB3
SR48UB3
SR48UBCL
SR48UBEXP
SR48UBEXPND
SR48UBEXPNDNR
SR48UBEXPNDNR3
SR48UBSP1
SR50UB
SR52UB
SR55UB
SRX42UBAB

5
Feature Identification
Model SRTH12UB shown.
1Roof Panel
2Locking Split Rear Doors
3Locking Side Panels
4Cable Management Rails
5Mounting Rails (Provide horizontal and vertical mounting points for equipment.)
6Locking Reversible Front Door
7Keys (One for the doors and one for the side panels.)
Not Shown: Mounting hardware, documentation, shipping brackets and other shipping materials.
1
3
6
3
2
4
4
5
5
5
5
7

6
Configuration
Before proceeding with configuration, make sure the unit is properly assembled and secured to the rack
enclosure. Refer to the Assembly Instructions document for step-by-step instructions.
Ground Connection
The unit includes multiple threaded grounding points labeled . To establish a ground, choose a grounding point and use the
included M6 screw to connect the frame of the unit directly to your facility’s earth ground connection with an 8 AWG
(3.264 mm) wire. Make sure to route the ground wire through the enclosure’s frame to ensure unhindered door operation.
WARNING: Attach each enclosure to earth ground separately. Do not use the enclosure without an earth ground
connection.
Adding or Removing Front and Rear Doors
WARNING: Do not attempt to add or remove doors without assistance.
90°
1
2
3
Removing Door
1Disconnect the door’s ground wire.
2Open the door until it is perpendicular (90 degrees) to the front
of the enclosure.
3Lift the door from the hinges and remove it from the enclosure.
To Reinstall Door, Reverse Steps 1-3

7
Reversing Front Door
WARNING: Do not attempt to reverse the front door without assistance.
1Remove the screw connecting the ground wire to the inside of the
door.
2Remove the 2 screws connecting the door handle to the door.
Remove the door handle.
3Remove the screw and washer from the rear of the door handle and
remove the latching mechanism. Rotate the latch washer counter-
clockwise 90 degrees and reverse the latch so it points in the
opposite direction, then use the screw and washer to re-attach the
latch to the rear of the door handle.
4Remove the door by following the steps in the previous section.
1
2
3
4
Configuration

8
Configuration
5Remove the door hinges from the enclosure, rotate them
180 degrees and attach them on the opposite side of the enclosure.
Note: The alternate door hinge attachment points have plastic plugs in the
screw holes. Remove the plugs and insert them in the original door hinge
attachment points.
6Unscrew the 2 hinge mechanisms from the hinge openings inside
the door, then reattach each of them using the set of screw holes
immediately opposite their original position.
7Rotate the door 180 degrees and reinstall it on the enclosure.
Remember to connect the ground wire to the inside of the door, using
the attachment point nearest the hinge at the top of the door. The
attachment point is marked with the ground connection symbol .
8Reinstall the door handle.
5
6
7
8

9
Configuration
Adding or Removing Roof Panel
WARNING: Do not attempt to use the roof panel for weight-bearing purposes other than those explicitly described
and approved by Tripp Lite. Do not attempt to add or remove the roof panel without assistance.
Removing Roof Panel
1Pull the 2 pins near the rear of the roof panel. While holding the pins,
push the roof panel upward.
2Remove the roof panel tabs Afrom the roof panel attachment slots
Bin the enclosure frame.
3Disconnect the ground wire located on the side panel.
4Lift the roof panel from the enclosure.
To Reinstall Roof Panel, Reverse Steps 1-4
2
1
A
B
1
2
3
4

10
Configuration
Adding or Removing Side Panels
1Open the latch by sliding it downward.
2Tilt the top of the panel away from the enclosure.
3Lift the panel away from the brace that supports it.
To Reinstall Side Panel, Reverse Steps 1-3
1
2
3

11
Configuration
Adjusting Mounting Rails and Cable Management Rails
WARNING: Do not attempt to adjust rails without assistance. Do not attempt to adjust rails while equipment is
installed in the unit. Do not attempt to use rails without screws installed (4 per rail).
The 4 mounting rails accommodate equipment with a mounting depth of 30 inches (762 mm). Do not adjust the mounting
rails unless your equipment requires a different mounting depth. The front and rear sets of rails can be adjusted independently
in ¼-inch (6 mm) increments for mounting depths between 4 inches (101.6 mm) and 42 inches (1066.8 mm).
1Each rail is connected to the enclosure with 4 screws - 1 pair at the
upper beam Aand 1 pair at the lower beam B.
2Remove the screws connecting the ground wire to the equipment
mounting rail.
3Remove the screws fastening each of the rear mounting rails to the
enclosure. (If adjustment of the front rails is required, you can also
remove the screws from the front rails.)
4Slide the mounting rails to the desired depth and reattach them
using the screws you removed in Step 2. The rail attachment points
are numbered Ato help you align each pair of rails at the same
depth.
The depth of the cable management rails can be adjusted using the same
method.
Note: Remember to reconnect the ground wires to the equipment mounting rails
using the attachment point located near the bottom of the unit. The attachment
point is marked with the ground connection symbol .
4 5 6 3 4 5 6 7 8 9 0 1 2 3 4 5 6
8
4 5 6 5 6 7 8 9 0 1 2 3 4 5 6 0 1 2 3 4 5 6 7 8 9 0 1 2 3
5
A
B
A
1
3
2
4

12
Equipment Installation
WARNING: Do not install equipment until you have assembled and secured the unit in accordance with
the Assembly Instructions. Install heavier equipment first and toward the bottom of the enclosure.
Install equipment starting from the bottom of the enclosure and proceeding toward the top of the
enclosure - never the reverse. If using sliding equipment rails, be careful when extending the rails. Do
not extend more than one set of sliding equipment rails at one time. Avoid extending sliding equipment
rails near the top of the enclosure.
Note: The square holes at the middle of each rack unit are numbered and also include a small notch to aid identification. A single rack unit
includes the space occupied by the numbered hole and the holes directly above and below.
24
25
26
27
28
29
23
22
21
20
19
18
24
25
26
27
28
29
23
22
21
20
19
18
24
24
2
1 Rack Unit
1 Rack Unit
Installing or Removing Cage Nuts
WARNING: The flanges of the cage nuts should engage the sides of the square opening in the rail, not the top and
bottom. Follow the instructions in your equipment documentation to ensure proper installation of your equipment.
20
19
18
22
21
20
19
18
22
21
1Locate the numbered square openings in the mounting rails
where you plan to install your equipment. You will install cage nuts
(included) into the square openings in order to provide an attachment
point for the mounting screws (included).
Note: Consult your equipment documentation to determine how many cage
nuts will be required and where they will need to be installed.
2From the inside of the mounting rail, insert one of the flanges of the
cage nut through the square opening. Press it against the side of the
square opening. Each flange should engage one side of the square
opening, not the top or bottom. 1
2

13
Equipment Installation
Specifications
3Compress the cage nut at the sides slightly to allow the remaining
flange to fit through the square opening. When the cage nut is
properly installed, both flanges will protrude through the square
opening and will be visible on the outer surface of the mounting rail.
Repeat steps 1-3 until all required cage nuts are installed.
4After installing the required cage nuts, use the included mounting
screws and cup washers to secure your equipment to the rack rail.
Place the cup washers between the screws and the equipment
mounting brackets.
Note: Your equipment may also include mounting hardware. Read the
mounting instructions that came with your equipment before installing your
equipment.
To Remove Cage Nuts, Reverse Steps 1-3
Note: You may wish to use a cage nut tool (user-supplied) to aid cage nut
installation and removal.
20
19
18
22
21
20
19
18
22
21
3
4
Model
Unit Dimensions Shipping Dimensions
Height Width Depth Weight Height Width Depth Weight
SRTH6UB 13.3”
(338 mm)
23.6"
(599 mm)
43"
(1092 mm)
84.8 lb.
(38.5 kg)
22.8"
(579 mm)
39.2"
(996 mm)
10.6"
(269 mm)
100 lb.
(45.4 kg)
SRTH12UB 23.9"
(607 mm)
23.6"
(599 mm)
43"
(1092 mm)
118 lb.
(53.5 kg)
24.4"
(620 mm)
39.2"
(996 mm)
15.4"
(391 mm)
132 lb.
(60 kg)

14
Storage and Service
Storage
The enclosure should be stored in a controlled indoor environment, away from moisture, temperature extremes, flammable
liquids and gasses, conductive contaminants, dust and direct sunlight. Store the enclosure in its original shipping container if
possible.
Service
Your Tripp Lite product is covered by the warranty described in this manual. A variety of Extended Warranty and On-Site Service
Programs are also available from Tripp Lite. For more information on service, visit tripplite.com/support. Before returning your
product for service, follow these steps:
1. Review the installation and operation procedures in this manual to insure that the service problem does not originate from
a misreading of the instructions.
2. If the problem continues, do not contact or return the product to the dealer. Instead, visit tripplite.com/support.
3. If the problem requires service, visit tripplite.com/support and click the Product Returns link. From here you can request
a Returned Material Authorization (RMA) number, which is required for service. This simple on-line form will ask for your
unit’s model and serial numbers, along with other general purchaser information. The RMA number, along with shipping
instructions will be emailed to you. Any damages (direct, indirect, special or consequential) to the product incurred during
shipment to Tripp Lite or an authorized Tripp Lite service center is not covered under warranty. Products shipped to Tripp Lite
or an authorized Tripp Lite service center must have transportation charges prepaid. Mark the RMA number on the outside
of the package. If the product is within its warranty period, enclose a copy of your sales receipt. Return the product for
service using an insured carrier to the address given to you when you request the RMA.

15
Warranty and Product Registration
5-Year Limited Warranty
Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in material and workmanship for a period of
5 years from the date of initial purchase. If the product should prove defective in material or workmanship within that period, Seller will repair or replace the
product, in its sole discretion.
THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE, ABUSE OR NEGLECT. SELLER MAKES NO
EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY SET FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED
WARRANTIES, INCLUDING ALL WARRANTIES OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE;
AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL DAMAGES. (Some states do not allow limitations on how long an implied
warranty lasts, and some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not
apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from jurisdiction to jurisdiction).
WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate or safe for the use intended. Since
individual applications are subject to great variation, the manufacturer makes no representation or warranty as to the suitability or fitness of these devices for
any specific application.
Product Registration
Visit tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically entered into a drawing for a chance to win a FREE Tripp Lite
product!*
* No purchase necessary. Void where prohibited. Some restrictions apply. See Web site for details.
Tripp Lite follows a policy of continuous improvement. Product specifications are subject to change without notice. Photos and illustrations may differ slightly
from actual products.
Note on Labeling
This symbol is used on the product: Ground Connection
1111 W. 35th Street, Chicago, IL 60609 USA • tripplite.com/support
20-09-242 93-3D32_RevB

16
Manual del Propietario
Rack de Expansión Vertical
SmartRack®
Modelos: SRTH6UB, SRTH12UB
(Números de Serie: AG-0545, AG-0546)
Para uso con Modelos SmartRack:
AGAC7006, AGAC7454, AGAC7761, AG-00BE, AG-0324, AG-0325, AG-0534, AG-0535, AG-0536
1111 W. 35th Street, Chicago, IL 60609, EE UU • tripplite.com/support
Copyright © 2021 Tripp Lite. Todos los derechos reservados.
English 1 • Français 31 • Русский 46

17
Instrucciones de Seguridad 18
Importantes
Gabinetes de Rack Compatibles 19
Identificación de Características 20
Configuración 21
Conexión a Tierra 21
Colocación o Retiro de las Puertas 21
Delanteras y Traseras
Retiro de la Puerta 21
Inversión de la Puerta Delantera 22
Colocación o Retiro del Panel de Techo 24
Colocación o Retiro de los Paneles 25
Laterales
Ajuste de los Rieles de Instalación y 26
Rieles para el Manejo del Cableado
Instalación del Equipo 27
Instalación o Retiro de las Tuercas de
Fijación 27
Especificaciones 28
Almacenamiento y Servicio 29
Garantía 30
Índice

18
Instrucciones de Seguridad Importantes
CONSERVE ESTAS INSTRUCCIONES
Todas las secciones de este manual contienen instrucciones y advertencias que deben observarse durante
la instalación y uso del Rack de Expansión Vertical descrito. Lea cuidadosamente todas las instrucciones y
advertencias antes de intentar mover, instalar o utilizar el Rack de Expansión Vertical descrito en este manual. El
incumplimiento creará un riesgo de lesiones personales y daños a la propiedad y puede invalidar la garantía.
• Mantenga el gabinete en un entorno interior controlado lejos de humedad excesiva, temperaturas extremas, líquidos y gases
inflamables, contaminantes conductores, polvo o luz solar directa.
• Deje espacio suficiente en la parte delantera y trasera del gabinete para una ventilación adecuada. No bloquee, cubra ni
coloque objetos en las aberturas externas de ventilación del gabinete.
• El gabinete es extremadamente pesado. Tenga cuidado al manipular el gabinete. No intente desempacarlo, moverlo o instalarlo
sin ayuda. Utilice un dispositivo mecánico como un montacargas o gato para tarimas para mover el gabinete en el contenedor
de embarque.
• No coloque ningún objeto sobre el gabinete, especialmente recipientes con líquidos y no intente apilar los gabinetes o más de
un ajuste de altura en la parte superior del gabinete.
• Inspeccione el contenido del Rack de Expansión Vertical para detectar daños en el embarque. No use el Rack de Expansión
Vertical si está dañado.
• Deje el gabinete en el contenedor de embarque hasta que haya sido movido tan cerca a su ubicación final como sea posible.
• El Rack de Expansión Vertical está diseñado para instalarse en la parte superior de los modelos de Gabinete SmartRack de
Tripp Lite que estén asegurados a la estructura del edificio para estabilidad.
• Este equipo está diseñado para ser instalado por personal de servicio entrenado y calificado.
• Instale el Gabinete SmartRack y el Rack de Expansión Vertical en un área estructuralmente firme con un piso nivelado que
pueda soportar la carga del peso del gabinete, de todo el equipo que se instale en el gabinete y otros gabinetes y otros
equipos que se instalen cerca.
• Asegúrese de conectar el gabinete a tierra. Vea Conexión a Tierra para obtener más información.
• Tenga cuidado cuando corte el material de empaque. El contenido podría haber sido rasguñado o rayado, causando daños no
cubiertos por la garantía.
• Guarde todo el material de empaque para uso posterior. Volver a empacar y enviar el gabinete sin el material de empaque
original puede ocasionar daños al producto que anularían la garantía.
• No reembarque el gabinete con equipo adicional a menos que el gabinete haya sido embarcado con una tarima especial anti-
impacto (solo modelos “SP1”). El peso combinado del gabinete y el equipo instalado no debe exceder la capacidad de carga
de la tarima. Tripp Lite no es responsable por cualquier daño que se produzca durante el reenvío.
• No se puede usar cuando hay niños presentes.
• No se recomienda el uso de este equipo en aplicaciones de soporte de vida en donde razonablemente se pueda esperar que
la falla de este equipo cause la falla del equipo de soporte de vida o afectar significativamente su seguridad o efectividad.
PRECAUCIÓN
CONEXIÓN A TIERRA

19
Gabinetes de Rack Compatibles
Los Racks de Expansión Vertical SRTH6UB y SRTH12UB son compatibles con los siguientes modelos de Gabinete SmartRack
de Tripp Lite:
Modelo Número de
parte
SR2400 AC8A08
SR25UB AC8480
SR25UB SR1090
SR25UB3 AC883F
SR25UB3001 SP87C0
SR25UBEXP SR1045
SR25UBSP1 AC7022
SR25UBSP1 SR1091
SR42UB AC89A3
SR42UB SP87BA
SR42UB SR1000
SR42UB007 AC8A52
SR42UB1032 SR1007
SR42UB3 SR1041
SR42UB3002 SP87BF
SR42UBC SR1089
SR42UBC001 AC881E
SR42UBCL SR1044
SR42UBCLSP1 AC89CF
Modelo Número de
parte
SR42UBEXP SR1002
SR42UBEXP001 SP87AA
SR42UBEXP002 SP87AB
SR42UBEXP003 SP87BE
SR42UBEXP004 SR107F
SR42UBEXP1032 SR8797
SR42UBEXPC001 AC881F
SR42UBEXPND SR1003
SR42UBEXPND3 SR1042
SR42UBEXPNDNR3 SR1004
SR42UBG SR1001
SR42UBG001 AC883E
SR42UBG3 SR107C
SR42UBG3001 AC8B66
SR42UBKD AC7174
SR42UBND AC8818
SR42UBSFDKD AC8AD9
SR42UBSP1 SR1005
SR45UB SR1014
Modelo Número de
parte
SR45UBEXP SR1019
SR45UBEXPND SR1020
SR45UBEXPNDNR3 SR1021
SR45UBND SR1015
SR45UBSP1 SR1022
SR48UB SR1052
SR48UB3 SR1064
SR48UB3 SR879A
SR48UBCL SR1053
SR48UBEXP SR1057
SR48UBEXPND SR1058
SR48UBEXPNDNR AC8841
SR48UBEXPNDNR3 SR1049
SR48UBSP1 SR1059
SR50UB AC003E
SR52UB AC003B
SR55UB AC003D
SRX42UBAB AC0024

20
Identificación de Características
Se muestra el modelo SRTH12UB.
1Panel de Techo
2Puertas Posteriores Divididas con Cerradura
3Paneles Laterales con Cerradura
4Rieles para el Manejo del Cableado
5Rieles de Instalación (Proporcionan puntos de instalación horizontal y vertical para los equipos.)
6Puerta Frontal Reversible con Cerradura
7Llaves (Una para las puertas y una para los paneles laterales).
No se Muestra: Accesorios de instalación, documentación, soportes de embarque y otros materiales de embarque.
1
3
6
3
2
4
4
5
5
5
5
7