Tripp Lite SRX2 User manual

3. Measure from the bottom of the Mounting Angle to the
top clip nut. Assemble clip nuts onto the three other rails
at the measured height.
Rack Mount Fixed And Roll-Out Shelves
Clip Nuts provide mounting points for rack mount
fixed and roll-out shelves.
Clip nuts have a front or screw side. Consider which
way it should face for ease of access to the screw
head during component installation. (figure 1)
To remove a clip nut from a mounting angle, insert a flat
blade screwdriver or knife under the tab on the front and
pry up, freeing the retaining ring from the mounting
angle. (figure 2)
1. Select the location at which the shelf will be mounted
in the enclosure assembly.
2. Snap one clip nut into the top hole of the selected
location.
(note: When mounting a roll-out shelf, insert a
10-32 screw partially into each clip nut.)
If the weight load will exceed 75 lbs. on a roll-out shelf,
use four clip nuts and screws in each of the brackets.
It will be necessary to select a four-hole grouping that
matches the mounting holes in the brackets. The center
two holes will measure 1/2" apart.
Two screws per bracket, one at the front and one at the
rear, is sufficient if the weight load will be less than
75 lbs.
CLIP NUT INSTALLATION
Rack Mount Fixed And Roll-Out Shelves
Figure 2
Mounting angle
Clip nut
1
#10-32 x 5/8" Pan
Head Machine Screw
Front or screw side
Clip nut
Figure 1
SRX2, SRX3 and SRX4
Manual Part #93-1937
01/18/02 rev. A

2. Align the shelf with the previously installed
clip nuts and attach the shelf with the 10-32
screws that are provided. Once the screws have
started in all four corners, tighten all of the screws.
FIXED SHELF ADJUSTMENT
1. To adjust the Fixed Shelf, loosen the bracket screws,
move the brackets, then re-tighten the screws.
(figure 5)
1. Install the front and rear shelf brackets as
shown on both the left hand and on the
right hand side of the shelf.
(figure 3)
FIXED SHELF INSTALLATION Figure 3
Clip nuts
Fixed shelf
#10-32 x 5/8" Pan
Head Machine Screws
Bracket
Shelf brackets
Screws
Shelf bracket
Lock nuts
#10-32 x 3/8" Phillips
Pan Head Screws
Figure 4
Figure 5
2
Rack Mount Fixed Shelves
SRX2 and SRX3
Manual Part #93-1937
01/18/02 rev. A

Required Tools:
Phillips Head Screwdriver
3/8” Nut Driver (or Socket Wrench)
11/32” Nut Driver (or Socket Wrench)
Fasteners That May Be Required:
3
#10-32 x 5/8” Phillips
Machine Screw
#10-32 x 3/8” Phillips
Pan Head Screw #10-32 Keps Locking Nut #10-32 Clip Nut
SRX2 & SRX3 Parts List
Item Description Qty.
1#10-32 x 5/8" Screw 12
2#10-32 x 3/8" Screw 8
3#10-32 Keps Locking Nut 8
4
4
5
12#10-32 Clip Nut
Stationary Shelf Bracket
Stationary Shelf Bracket
Rack Mount Fixed And Roll-Out Shelves
SRX2, SRX3 and SRX4
Cable Management Arm
(included with SRX4 only)
SRX4 Parts List
Item Description Qty.
1#10-32 x 5/8 Screw 16
2#10-32 Clip Nut 16
3Slide Bracket 2
4
2
5
1Warning Label
#8-32 x 3/8 Screw
2
6#8-32 Keps Locking Nut
1
7Cable Management Arm
#8-32 x 3/8" Phillips Pan
Head Machine Screw
#8-32 Hex Lock Nut
Manual Part #93-1937
01/18/02 rev. A