Trust 100B User manual

TRUST WIRELESS SECURITY CAMERA 100B
1
1 Introduction
This instruction manual is for users of the ‘TRUST WIRELESS SECURITY CAMERA
100B‘. The camera makes is possible to expand your existing 2.4 GHz system without
wires. The TRUST WIRELESS SECURITY CAMERA 100B is to be used to protect
your property. This camera operates without wires via radio frequency. This CAMERA
can also be used in the dark. The camera can be connected to receivers of the Trust
100 series wireless products. The camera can also be used with other 2.4 GHz
wireless systems provided that they operate with the same technology; we cannot
guarantee the operation of this combination.
2 Safety
Before use, read the following instruction with care:
1. Do not use this device in damp environments, such as a bathroom, damp
basement, swimming pool, etc.
2. Never insert objects in the slots on the outside of the device, because you
could touch parts which are live. This may cause fire or electrical shocks.
3. Do not try to repair this device yourself. If you open a housing or remove it,
you could accidentally touch parts which are live. You also run other risks.
4. Position the device so that the cables cannot be damaged.
5. This device has been approved according to the European R&TTE
guidelines. The device works using a 2.4GHz sender/receiver. If in doubt,
check whether the use of this device is permitted in your country.
3 Connecting
Attention: In France, the law only permits the use of channel 3.
3.1 Connecting the adapter
By using the adapter supplied with it, you can connect the camera to the electricity
supply. Insert the plug of the power adapter into the DC ‘D’ as in figure 3. Plug the
power adapter into the electrical outlet.

TRUST WIRELESS SECURITY CAMERA 100B
2
UK
3.2 Placing batteries (optional)
1. Remove the battery flap on the bottom left-hand side of the camera as
indicated in figure 1.
2. Insert the batteries into the battery compartment as shown in figure 2. You
can also see how the batteries must be installed on the inside of the camera.
3. Close the battery flap.
Note: Inserting the batteries incorrectly can cause damage.
Note: Only use batteries of the AA alkaline type or rechargeable NiMH.
Note: If you want to use the adapter supplied with the camera and you
have inserted the batteries, you do NOT have to remove the
batteries.
4 Adjusting and placing the camera
4.1 Setting the channels
Set the channel of the camera by means of switch ‘A’ as in figure 3.
Select channel 1, 2, 3 or 4.
Note: You will find more information about your receiver in the manual of your
TRUST 100 series receiver.
4.2 Voltage switch
You can switch the camera on, off and to night vision with switch ‘C’ as in figure 3. If
the LED ‘B’ as in figure 3 is lit up the camera is live.
4.3 Directing the camera
The camera lens can be turned 90 degrees up and down. On the stand, the camera
can be adjusted 30 degrees up and down and 200 degrees to the left and the right.
See figure 4.
4.4 Adjusting the aerial
Adjust the aerials so that the curve of both the transmitter and receiver aerial are
directed towards each other; in case you use more cameras, adjust the aerials as
ideally as possible. Keep the aerials folded if the transmitter and receiver are less than
three metres apart.
Note: The aerial cannot be turned through 360°. Stop turning the aerial when
you feel some resistance. If you continue turning after feeling some
resistance, the device will be damaged and can no longer be used.

TRUST WIRELESS SECURITY CAMERA 100B
3
5 Technical information
Description: Response:
Image [COLOUR / BLACK & WHITE] BLACK & WHITE
Optic module [CCD / CMOS / ...] CMOS
Lens [Inch] 1/4"
Microphone integrated [y / n] yes
Adapter 9V / 300 mA
RF approval no. (CE xxxx !) CE0123!
Wireless technology [RF, IR, ... +
frequency]
RF / 2,4 ~ 2,4875 GHz
FREQUENCY PER CHANNEL [1 / 2 / 3 / 4] 2, 434 / 2, 453 / 2, 473 / 2, 411 GHz
Camera dimensions 160 (antenna open) x 80 x 145
Receiver dimensions 115 x 105 x 145
Package size [HxWxD(mm)] 100 x 315 x 190
Gross weight (kg) 0.2

TRUST WIRELESS SECURITY CAMERA 100B
4
UK
6 Troubleshooting
Problem Cause Possible solution
Camera is in the off-
position.
Turn the camera on.
The camera is in a dark
room and is not switched
to the night vision
position.
Set the on, off switch to
the correct position.
The adapter is not
connected.
Connect the adapter to
the camera.
The batteries have not
been inserted into the
camera correctly.
Insert the batteries or
insert them correctly.
The channel selected is
not selected on your
receiver.
Select the correct channel
on the camera or receiver.
Camera gives no image
or a bad image.
The aerials are not
directed correctly.
Direct the curved sides of
the aerials towards each
other.
Register your product via www.trust.com, entitling you to optimum warranty and
service support such as up-to-date FAQ and the most recent drivers. In addition, you
will automatically be informed of the development of your and other Trust products.
And you have a chance to win spectacular prizes.
If you still have problems after trying these solutions, please contact one of the Trust
Customer Care Centres. You can find more information at the back of this instruction
manual. Please have the following information available:
•The article number, in this case: 12422 (European version) or 12423 (English
version);
•A good description of what does not work;
•A good description of when the problem occurs.