Trust 100S User manual

TRUST WIRELESS SECURITY CAMERA SYSTEM 100S
1
1 Introduction
This instruction manual is for users of the ‘TRUST WIRELESS SECURITY CAMERA
SYSTEM 100S ‘. The WIRELESS SECURITY CAMERA SYSTEM 100S is to be used
to protect your property. This device works using radio frequencies and, therefore,
does not require any cables.
Advantages:
•Without wires, passes on video and audio received by the camera
•The 2.4 GHz FM signal passes through walls, floors and ceilings.
•Can be extended with the Trust 100 series security cameras
2 Safety
Before use, read the following instruction with care:
1. Do not use this device in damp environments, such as a bathroom, damp
basement, swimming pool, etc.
2. Never insert objects in the slots on the outside of the device, because you
could touch parts which are live. This may cause fire or electrical shocks.
3. Do not try to repair this device yourself. If you open a housing or remove it,
you could accidentally touch parts which are live. You also run other risks.
4. Position the device so that the cables cannot be damaged.
5. This device has been approved according to the European R&TTE
guidelines. The device works using a 2.4GHz sender/receiver. If in doubt,
check whether the use of this device is permitted in your country.

TRUST WIRELESS SECURITY CAMERA SYSTEM 100S
2
UK
3 Connecting
Attention: In France, the law only permits the use of channel 3.
3.1 Components
The connections and switches of the receiver are specified in table 1 and figure 1.
Item: Description: Purpose:
AChannel selection switches Select the channel with this.
BAudio Left (White) Connect the left ‘audio in’ of
the TV to this.
CAudio Right (Red) Connect the right ‘audio in’
of the TV to this.
DVideo (Yellow) Connect the ‘video in’ of the
TV to this.
EConnection for adapter (9VDC
300mA)
Connect the adapter to this.
Table 1: Receiver connections
The connections and switches of the camera are specified in table 2 and figure 2.
Item: Description: Purpose:
AChannel selector switch Select the channel with this.
BVoltage indicator This indicates whether the
camera is live.
COn / off night vision switch Select camera on, off or on
night setting
DConnection for adapter (9VDC 300
mA)
Connect the adapter to this.
Table 2: Camera connections
3.2 Connecting the adapter
Connect the adapter plug to the DC connection, see item E in figure 1. You can turn
the receiver on and off with switch ‘A’ , as in figure 3. When LED ‘B’ is lit up the
receiver is live.
3.3 Placing batteries (optional)
If you do not want to or cannot use an adapter for the camera, you can also provide
the camera with batteries. These are optional and therefore must be bought
separately. The batteries used are type AA.
1. Remove the battery flap on the bottom left-hand side of the camera.

TRUST WIRELESS SECURITY CAMERA SYSTEM 100S
3
2. Insert the batteries into the battery compartment as shown in figure 4. You
can also see how the batteries must be installed on the inside of the camera.
3. Close the battery flap.
Note: Inserting the batteries incorrectly will cause damage.
Note: Only replace the batteries with the same type of alkaline or
rechargeable NiMH batteries (4 x AA).
4 Setting the channels
The receiver and the camera must be set to the same channel. The channels between
the camera and receiver must be set as follows.
4.1 Receiver
Switch the receiver to a specified channel by using the ‘A’ switches, as in figure 1.
Switch
Channel 12344
Channel 1 ON OFF OFF OFF OFF
Channel 2 OFF ON OFF OFF OFF
Channel 3 OFF OFF ON OFF OFF
Channel 4 OFF OFF OFF ON OFF
Table 2: Channel settings
4.2 Camera
Set the channel of the camera by means of switch ‘A’, as in figure 2. Select the
channel you have selected on the receiver.

TRUST WIRELESS SECURITY CAMERA SYSTEM 100S
4
UK
5 Directing the camera
The camera lens can be turned 90 degrees up and down. On the stand, the camera
can be adjusted 30 degrees up and down and 200 degrees to the left and the right.
See figure 5.
6 Adjusting the aerial
Adjust the aerials so that the curve of both the transmitter and receiver aerial are
directed towards each other; in case you use more cameras, adjust the aerials as
ideally as possible. Keep the aerials folded if the transmitter and receiver are less than
three metres apart.
Note: The aerial cannot be turned through 360°. Stop turning the aerial when
you feel some resistance. If you continue turning after feeling some
resistance, the device will be damaged and can no longer be used.
7 Extending
7.1 Extending the wireless security system
If you have several black / white or colour cameras and/or receivers available, you can
extend your wireless system. The condition for this to function well is that the
additional cameras and/or receivers to be connected operate on the same frequency
(signal). The number of receivers can be extended unrestrictedly within the system.
The number of cameras that can be connected in addition is three (so four in total).
The receiver is equipped with the auto-sequence function. This means that the
receiver can switch automatically among channels and thus also among cameras.
This makes it possible to secure several locations simultaneously. The interval
between switching channels can be set on the receiver.
8 seconds: Set dip-switch 5 of the receiver to ‘on’ (switch up)
4 seconds: Set dip-switch 5 of the receiver to ‘on’ (switch up)
Using the camera with auto-sequence function:
1. Connect the camera to the adapter supplied with it or use batteries (optional).
2. Set the channel selector switch to a free channel by using table 2. See figure
4.
3. Next, select the channels which are being used by the cameras by setting the
dip-switches on the receiver, using table 2. See figure 1.
4. The wireless system now operates with two cameras and the auto-sequence
function.
It is also possible to view the selected room by manual control; proceed as follows:
1. Connect the camera to the adapter supplied with it or use batteries (optional).

TRUST WIRELESS SECURITY CAMERA SYSTEM 100S
5
2. Switch the channel selector of the camera to a free channel. See figure 2
button ‘A’.
3. Next, select the channel of the camera selected by setting the dip-switches on
the receiver, using table 3. See figure 1.
4. Should you want to switch to a different room in your house in which a camera
is set up, you need only switch to the channel to which the camera is set.
5. The wireless system now operates with two cameras without the auto-
sequence function.
7.2 Extension into a wireless audio / video system
If you have several black / white or colour cameras and/or receivers from the Trust
100 series wireless devices available, you can extend your system without wires. The
condition for this to function well is that the additional cameras and/or receivers to be
connected operate on the same frequency (signal). The number of receivers can be
extended unrestrictedly within the system. The number of transmitters that can be
connected in addition is three (so four in total).
8 Technical information
Description: Response:
Signal type [PAL / SECAM / NTSC / ...] PAL
Image [COLOUR / BLACK & WHITE] BLACK & WHITE
Optic module [CCD / CMOS / ...] CMOS
Lens [Inch] 1/4"
Microphone integrated [y / n] yes
Adapter 9V / 300 mA
RF approval no. (CE xxxx !) CE0123!
Wireless technology [RF, IR, ... +
frequency]
RF / 2,4 ~ 2,4875 GHz
Frequency per channel 2, 434 / 2, 453 / 2, 473 / 2, 411 GHz
Camera dimensions 160 (antenna open) x 80 x 145
Receiver dimensions 115 x 105 x 145
Package size [HxWxD(mm)] 100 x 315 x 190
Gross weight (kg) 0.2

TRUST WIRELESS SECURITY CAMERA SYSTEM 100S
6
UK
9 Troubleshooting
Problem Cause Possible solution
Receiver not connected to
the TV correctly.
Connect the receiver to
the TV correctly.
Batteries placed
incorrectly.
Put the batteries in again.
The camera batteries are
empty.
Replace the camera
batteries.
Set to wrong channel. Set both camera and
receiver on the same
channel.
Change the channels of
both camera and receiver.
Change the physical
location of the camera
(transmitter) and / or
receiver by changing the
direction or distance.
Different RF device
operates on the same
channel.
Do not use the RF
products simultaneously.
Aerials are not directed
correctly.
Direct the curved side of
the aerials towards each
other.
No image on the TV.
The camera is located in
a dark room and night
vision is not switched on.
Switch on the camera’s
night vision.
The image gets worse
as several cameras are
used.
The camera’s aerials are
no longer directed
correctly.
Direct the curved sides of
the aerials towards each
other as efficiently as
possible or change the
location of the receiver or
of one of the cameras
The camera’s batteries
are empty.
Replace the camera’s
batteries.
Camera suddenly stops
operating.
Adapter plug is not fully
inserted.
Fully insert the plug into
the camera.
Register your product via www.trust.com, entitling you to optimum warranty and
service support such as up-to-date FAQ. In addition, you will automatically be
informed of the development of your and other Trust products. And you have a
chance to win spectacular prizes.

TRUST WIRELESS SECURITY CAMERA SYSTEM 100S
7
If you still have problems after trying these solutions, please contact one of the Trust
Customer Care Centres. You can find more information at the back of this instruction
manual. Please have the following information available:
•The article number. This is 12297 (European version) or 12298 (UK version);
•A good description of what does not work;
•A good description of when the problem occurs.