TSI Instruments 801903 User manual

_______________
TSI and TSI logo are registered trademarks of TSI Incorporated.
DustTrak is a trademark of TSI Incorporated.
3M, the 3M logo and Command are trademarks of 3M.
WIRELESS ROUTER
ACCESSORY (801903/801906) FOR
ENVIRONMENTAL ENCLOSURE
8535
INSTALLATION GUIDE
Thank you for purchasing an Environmental DustTrak™
Aerosol Monitor Wireless Router Accessories
(PN 801903 & 801906). These instructions will help you
quickly install your Wireless Router into the
Environmental Enclosure (PN 8535).
Unpacking the Wireless Router
Accessories
1. Carefully unpack the Wireless Router and Mounting
Kit from the shipping container and verify that all the
items listed in the following table are present.
2. Contact TSI immediately if items are missing or
broken.
3. The DustTrak model numbers 8530(EP) and
8533(EP), should be installed into the enclosure
prior to starting this installation procedure.
4. Configuration of the wireless router and DustTrak
Ethernet IP address should be completed prior to
starting this installation procedure.
Qty.
Item Description
Reference Picture
1
GL-AR150
Wireless Router
with USB Cable
1
4” Wireless 1dB
Hinged Antenna
1
12” RJ45 Cable
Cat 6
Qty.
Item Description
Reference Picture
1
18” RP-SMA
Extension Cable
(Male to Female)
with antenna post
and sealing gland
1
O-ring
1
3M™
Command™
brand Strips 6 PK

–2–
Tools Needed for Installation
Adjustable Wrench capable of opening to 1.188”
Phillips Screwdriver
Installing Wireless Router into
the Environmental Enclosure
1. DustTrak monitor’s
power should be off
prior to starting this
procedure.
2. Using a Phillips screwdriver, remove the two screws
on the left side of the enclosure. Using an adjustable
wrench, also remove the gland seal on the same
side. The image below illustrates what the enclosure
should like after the screws and gland have been
removed.
N O T E
DO NOT discard any components that have
been removed.
3. Install the O-ring
into the groove on
the antenna
assembly.
4. Remove the outer most nut on the gland seal.
5. Using a Phillips screwdriver, attach the antenna
assembly to the side of the enclosure using the two
screws removed in Step 1.

–3–
6. Using the nut that was removed in Step 4, attach the
gland seal to the side of the enclosure. If needed,
use an adjustable wrench to apply a small amount
additional of torque to the nut.
7. Remove blue liner
and attach a 3M™
Command™ brand
strip to the back of
the wireless router.
Be sure not to cover
the vent holes. Refer
to the Command™
brand strip box for
additional
instructions.
8. Connect the USB
cable and the RJ45
cable to the router.
9. Remove the black liner and attach the router to the
metal plate inside the enclosure.
10. If the external pump is present, mount the router to
the top of the pump as shown.
11. Connect the
antenna cable to the
router.
12. Connect the USB
cable and RJ45
cable to the
DustTrak
instrument.

TSI Incorporated –Visit our website www.tsi.com for more information.
USA Tel: [phone]
UK Tel: [phone]
France Tel: [phone]
Germany Tel: [phone]
India Tel: [phone]
China Tel: [phone]
Singapore Tel: [phone]
P/N 6010781 Rev. A ©2017 TSI Incorporated Printed in U.S.A.
13. Screw the hinged antenna to
the top of the antenna
assembly.
14. Using the adjustable wrench, tighten the
compression nut on the outside of the gland to
create a water-tight seal between the gland and
antenna cable as shown in the picture. Be careful
not to over-tighten.
15. Power on the
DustTrak Aerosol
Monitor. After two
(2) minutes, the red
and green LEDs on
the wireless router
will also be on.