Tundra Drone Siren Herder User manual

Siren Herder
Quick start guide

Siren Herder
The Tundra Drone Siren Herder is a drone accessory with siren sound for DJI Mavic drones. It
features a 107dB fast pulse siren tone and is easily controlled from remote DJI remote control. The
Siren Herder is quick to mount and unmount without any physical modifications of your drone. The
Siren Herder is equipped with internal rechargeable battery that can be charged using the USB micro
cable that was delivered with your DJI drone. The battery lasts about a full day with normal use. It is
small and lightweight with only 89 grams (0.2 lbs).
1. Sound output
2. Low battery status indicator
3. Power ON indicator
4. Charging status indicator
5. Micro USB port
6. Power switch
7. Connector for remote sensor
8. Velcro for securing cable
9. Remote sensor
1
2
3
3
4
5
6
7
8
9

Preparing the DJI Go app for use with the Siren Herder
1. Tap the three dots
2. Tap on the radio controller symbol.
3. Tap on the field on the right side of “C2”and scroll up till you find «Turn on/off Head LEDs»
and tap on that.
4. That`s it, you are ready to start using Siren Herder.
1
2
3
4

Charging the battery
Use the charger and micro USB cable provided with your DJI drone to charge the Siren Herders
battery. If the charging indicator is not lit then the battery is already fully charged. Charging time for
empty battery can take up to 3 hours, depending on the charger you use.
How to use
1. Prepare the Mavic drone for flight. Power it up and make sure that DJI GO app connects to
the drone. Turn off front LEDs by pressing C2 button on the controller.
C2

2. Be sure that the Siren Herder is turned off and mount it to the drone by sliding it backwards
on the drone as shown below.
Slide it from front to back
«CLICK»
Slide until clips lock.

3. Slide the remote sensor on the front left arm below the propeller. The remote sensor should
cover the LED on the drone. The cover has sliding guides shown with black arrows below
(only mavic 2 version) that should go into the lower trace shown with orange arrow below.
Important: Make sure that the remote sensor is on the lower trace (only mavic 2 version),
otherwise it will touch the motor.

4. Use the Velcro to secure the remote sensor cable to the front left arm.
5. Turn on the power switch on the Siren Herder by sliding the power switch forwards.

Important safety information
Read these instructions and follow all warnings.
Use:
-The Siren Herder outputs a very loud sound that can harm your hearing.
-Never use the Siren Herder indoors
-Never use it stationary without hearing protection for you and those around you
-Do not activate the Siren Herder before you have flown at least 20m away
-Do not use in rain, snow or wet weather conditions
-Do not expose the device for moisture
-Do not place the device where it can be exposed to excessive heat or a dusty enviroment
Siren Herder is equipped with a rechargable lithium battery. Lithium batteries can have regulations
for transportation etc.
Can not be used in combination with DJI Goggles.
Specifications
Sound output 107dB
Operating temperature -10⁰C to 40⁰C (14⁰F to 104⁰F)
Battery 3.7V 1200mAh
Charging temperature range 5⁰C to 40⁰C (41⁰F to 104⁰F)
Product size 12x9x6cm / 4.72x3.54x2.36 ''
Weight 89g (0.2 lbs)
For online support, please email [e-mail] or visit our website tundradrone.com