Turboair TAS-09SVH User manual

SPLIT AIRCONDITIONING SYSTEM
INSTALL MANUAL
TAS-09SVH
TAS-12SVH

2
Safety instructions
PLEASE READ THE FOLLOWING SAFETY
INSTRUCTIONS BEFORE INSTALLING AND
OPERATING THE UNIT:
This air conditioner meets strict safety and operating
standards. The installer of this unit must install or
service this unit so it operates safely and efficiently.
The lightning flash with arrowhead
symbol, within an equilateral triangle is
intended to alert the user to the
presence of uninsulated dangerous
voltage within the product’s enclosure
that may be of sufficient magnitude to
constitute a risk of electric shock to
persons.
The exclamation point within an
equilateral triangle is intended to alert
the user to the presence of important
operating and maintenance (servicing)
instructions in the literature
accompanying the appliance.
The installation instructions are for a experienced
installer. If you are not an experienced installer,
contact a local installer for help.
The manufacturer shall in no way be responsible for
improper installation or maintenance service,
including failure to follow the instructions in this
manual.
•Do not plug in the unit until all connections (tubing,
drain hose,mounting, etc.) have been made and
double checked.
•High voltages are present in this unit and are very
dangerous. Please refer to these instructions and
diagrams when wiring. Improper connections or
inadequate grounding can cause accidental injury.
•This unit must be grounded in accordance with local
electrical codes.
•Connect wires and pipes securely and tightly as
loose connections/ wiring may cause overheating at
connections and a possible fire hazard.
•When transporting the unit, be very careful and get
help as the units are very heavy. Be careful of sharp
edges on the units also.
•When installing in a ceiling or wall, make sure the
ceiling/wall is strong enough to hold the unit’s
weight. A frame may be necessary for added
support.
•When installing in a room, make sure the tubes are
well insulated to protect the walls and furniture from
sweating of the tubes.
•When installing in moist or uneven locations, make
sure to use a raised level concrete pad or concrete
blocks to provide a level, solid foundation for the
outdoor unit; this prevents water damage and
vibration.
•When installing in an area of high winds, make sure
to securely anchor the outdoor unit down with bolts
and a metal frame.
•Keep all tubing as short as possible.
•Use the flare method for connecting tubing.
•Apply refrigerant lubricant to the matching surfaces
of the flare and union tubes before connecting them,
then tighten , making sure not to overtighten.
•Check the tubes carefully for leaks before starting
the test run.
IMPORTANT NOTES
• Adhere to all safety instructions and warnings
throughout this manual.
• Read this manual carefully before installing or
operating this unit to become familiar with it’s
features and obtain the performance that will bring
you continued enjoyment for many years.
• Follow each installation or repair step exactly as
shown in the manual.
• Observe all local, state and national electric codes.
Contact your local government for more information
on electrical codes.
Contact Installer if Necessary:
If Unit is Installed Improperly:
Precautions When Wiring:
Precautions When Installing:
When Connecting Refrigerant Tubing:
Precautions When Transporting:
WARNING:
• ELECTRICAL SHOCK CAN CAUSE SEVERE
PERSONAL IN-JURY OR DEATH. ONLY A
QUALIFIED, EXPERIENCED ELECTRICIAN/
INSTALLER SHOULD ATTEMPT TO WIRE THIS
SYS-TEM.
• THE APPLIANCE IS NOT INTENDED FOR USE
BY CHIL-DRENOR INFIRM PERSONS WITHOUT
SUPERVISION.
• YOUNG CHILDREN SHOULD BE SUPERVISED
TO ENSURE THAT DO NOT PLAY WITH THE
APPLIANCE

• Make sure the power is off and the unit is unplugged
before opening the unit to troubleshoot or repair
electrical parts and wiring.
• Keep your fingers and clothing away from any moving
parts.
• Clean up the sight after you finish, making sure no
metal scraps and wiring are left in the unit.
• The Air conditioner shall be installed in accordance
with the na-tioned wiring regulation.
• The equipment fulfills the requirements in EN 61 000-
3-11 and is subject to conditional connection to the
mains.
• It may be connected in consultation with the supply
authority.
• The equipment may only be connected to a mains
supply with a system impedance of less than 0.3
ohm.
• The system impedance in the interface point may be
obtained from the supply authority.
• If the mains supply has a higher system impedance,
short voltage dips may appear when the equipment is
started or during opera-tion.
• This may influence or disturb the operation of other
apparatuses, e.g. flickering lamps, especially those
connected to the same supply mains.
ROOM AIR CONDITIONER INSTRUCTION
Remark per EMC Directive 89/336/EEC
To prevent flicker impressions during the start of the
compressor (technical process) following installation
conditions do apply.
1. The power connection for the air conditioner has to be
done at the main power distribution. This distribution
has to be of an low impedance. Normally the required
impedance is reached at a 32A fusing point. Air
conditioner fuse has to be 16A max!
2. No other equipment has to be connected to this power
line.
3. For detailed installation acceptance please refer to your
contract with the power supplier. If restrictions do apply
for products like washing machines, air conditioners or
electrical ovens.
4. For power details of the air conditioner refer to the
rating plate of the product.
When Servicing:
Safety Instructions ......................2
Installation Diagram(Indoor Unit)
Installation ....................................4
Precautions for Selecting the Location.....5
Installing the Wall Bracket.........................5
Installing the Indoor/Outdoor Wire to
the Indoor Unit for AC Connection............6
Connecting Copper Tubes........................7
Conneting the Drain Hose.........................9
Installing the Indoor/Outdoor Wire
to Outdoor Unit for AC Connection.........10
Taping up the Wire/Tubing/Hose.............11
Applying Putty and Inserting Wall Cap ...11
Air Purging ...............................................12
Air Purging with Vacuum Pump..............12
Test Run...................................................13
Pump Down............................................13
Contents
Disposal of Used Electrical &
Electronic Equipment
The meaning of the symbol on the product, its
accessory or packaging indicates that this
product shall not be treated as household
waste. Please, dispose of this equipment at
your applicable collection point for the
recycling of electrical & electronic equipments waste. In the
European Union and Other European countries which there
are separate collection systems for used electrical and
electronic product. By ensuring the correct disposal of this
product, you will help prevent potentially hazardous to the
environment and to human health, which could otherwise be
caused by unsuitable waste handling of this product. The
recycling of materials will help conserve natural resources.
Please do not therefore dispose of your old electrical and
electronic equipment with your household waste. For more
detailed information about recycling of this product, please
contact your local city office, your household waste disposal
service or the shop where you purchased the product.

4
Installation Diagram(Indoor)
Below is an overview for the connection of the the Indoor unit to the Outdoor unit. The pages following will give
detailed instructions for full installation. Remember to read the complete Installation section and follow all the safety
instructions fully when installing the Indoor and Outdoor units.
OVERVIEW
TAS-09SVH/12SVH
16.4 49 Ft
16.4Ft 0.5 oz
TAS-09SVH/125SVH

5
INDOOR UNIT
Do not install the unit in an area with direct sunlight, near
heat sources (radiator, etc.), or an area where leakage of
flammable gas may be expected.
Select a position in the room, high on the wall, where the
whole room can be uniformly cooled.
Select a location that can hold the weight of the unit and
where the copper tubing, drain hose and Indoor to Outdoor
Wire have the shortest distance to the Outdoor unit.
Make sure the Indoor unit is installed at least 10cm (3.95in)
away from the top and left side wall and at least 30cm
(11.8in) from AC outlet and right side wall.
(see Overview figure on previous page)
OUTDOOR UNIT
Do not install the unit in an area near heat sources,
exhaust fans, or an area where leakage of flammable gas
may be expected.
Do not install the unit in a humid, damp or uneven location.
Select a location that is well ventilated .
Leave enough room around the unit for air intake, exhaust
and possible maintenance.
PRECAUTIONS FOR SELECTING THE LOCATION
INSTALLING THE WALL BRACKET:
1. Determine the type of wall (sheetrock, concrete, etc.)
and make sure it is strong enough to hold indoor unit.
Select an approximate position for the unit, taking the
required distances away from walls/AC outlet into
consideration.
2. Determine if the hole is to be made at the left or right
hole location.
3. Using drill with hole-cutting attachment or equivalent, cut
a hole 65mm (2.56") in diameter. The hole should be
made at a slight downward slant to the outdoor side.
Measure the thickness from the inside to outside edges
and cut a PVC pipe at a slight angle 1/4" shorter than the
thickness of the wall and insert pipe in wall.
4. For sheetrock, wooden or similar wall, measure down
from the ceiling using a level or tape measure and attach
the wall bracket to the wall using 4 screws. If you are not
able to line up the holes with the beams, use toggle
bolts. Make sure the wall bracket is even and flush
against the wall.
Indoor Outdoor
Cut at slight angle
CAUTION
Before making hole, make sure there are no studs, pipes, electrical wiring or conduit directly behind the area to be cut.
For Concrete, or similar type wall, make holes into the wall and insert concrete nails instead of screws.
To install the wall bracket, follow the procedures below. One hole is required for the tubing and may be either on the left or right side.
DSB-0910L/LH, DSB-1210L/LH
DSB-F0910PH-DV, DSB-F1210PH-DV
TAS-09SVH
TAS-12SVH

6
TAS-09SVH/12SVH
INSTALLING THE IN DOOR/OUTDOOR WIRE TO THE INDOOR UNIT FOR AC CONNECTION
18AWG
TAS-09SVH
TAS-12SVH
TAS-09SVH
TAS-12SVH

7
To connect the copper tubes, follow the procedures below:
1. At flare working, put the copper tube into standardized dimensional hole of the bar to work at over “ ⓑ ”size from
the surface of the bar. (Do flare work after remove all burrs)
•Be sure to work after putting the flare nut on the copper tube.
FLARE TOOL
HANDLE
Bar
COPPER TUBE
Bar COPPER TUBE
COPPER TUBE
CONNECTING COPPER TUBES
2. Work after sealing flare parts just until connecting copper tubes because soil, dust, sand etc can be inflowed into
section of copper tube when drill a hole in the wall.
* An example of wrong
•description : Gas leakage happened due to
wrong flare working
•symptom : Gas leakage and assembly
defect happened due to wrong
dimension at flare working
The flare nut wasn't
assembled be cause the
copper tube was work too
big.
If the working size is too
small, it hangs at flare nut
weakly so leakage is easily
happened by even small
impact.
Cap or Vinyl
Bend
Bend Cap or Vinyl Copper tube
Be cautious not to reach
Dust Burrs do enter the copper tube
ⓑ

8
Pipe(Ø) B (in) A (Ø) Torque
6.35(1/4") 0.02~0.05 9.1(0.36) 125~152lbf/in
9.52(3/8") 0.02~0.04 13.2(0.52) 289~353lbf/in
12.70(1/2") 0.02~0.04 16.6(0.65) 438~534lbf/in
15.88(5/8") 0.04 19.4(0.76) 545~667lbf/in
3. After align the center of the copper tube sufficiently tighten the flare nut by hand and to connect as turning by
spanner. Follow the procedures below. (To prevent gas leakage, apply refrigeration machine oil on both inner and
outer surfaces of the flare nut)
CAUTION
•All copper tube bends should be as gentle as possible.
•Connect liquid tube to the service valve of outdoor unit after connecting gas tube.
•Be sure to check gas leakage after connecting tube job is finished.
(EVA, CONDENSER, SERVICE VALVE, etc.)
•Be sure to use two spanner when connecting tube valve are connected. One of them is
for supporting service valve or body of EVA union, the other is for tightening flare nut of connecting tube.
Bolt Flare nut
Spanner(fixed) Torque wrench
Copper tube Union
Flare nut
Be align the center
Bolt Flare nut
•Working dimension according to copper tube

9
1. Drain hose have to be descends to outdoor.
2. Do not install drain hose.(see below)
3. If extended hose is indoor, seal outside of hose.
4. Open the front panel and pour water to check the
drainage condition.
Installed at
high position Tip of drain hose
dipped in water Tip of drain hose
dipped in sewer
Bent Gap is not enough
from the ground
Less than
2.0in
To connect the drain hose, follow the procedures below:
CONNECTING THE DRAIN HOSE
Indoor
Indoor unit drain hose
Insulator Outdoor
Extend hose Hose
Hose connection

10
16AWG
INSTALLING THE INDOOR/OUTDOOR WIRE TO THE OUTDOOR UNIT FOR AC CONNECTION
TAS-09SVH
TAS-12SVH