Turboair TIM-50A User manual

Ice-maker User Manual

Contents
1. Product features ------------------------------------------------------------------------------------ 1
2. Product accessories -------------------------------------------------------------------------------- 2
3. Product specifications -----------------------------------------------------------------------------3
4. Product structure ----------------------------------------------------------------------------------- 4
5. Installation------------------------------------------------------------------------------------------- 5
1) Unpacking and installation
2) Connection of inlet pipe and drain pipe
6. Precautions for the use of power cord ------------------------------------------------------- 7
7. Product earthing------------------------------------------------------------------------------------ 7
8. Description of control panel--------------------------------------------------------------------- 8
1) Details of control panel
2) Functions of buttons on control panel
9. Basic operations of control panel--------------------------------------------------------------9
10. Fault code identification -----------------------------------------------------------------------10
11. Operation of cleaning functions--------------------------------------------------------------11
12. Verify before applying for aftersales repair! ----------------------------------------------12
13. Aftersales services guideline ------------------------------------------------------------------13

1
1. Product features
Thank you for purchasing our product.
Make sure to read this manual in order for safe use.
■ MICOM control
→Electronic temperature control is introduced to automatically regulate ice size according to
ambient temperature in the production process.
■Ice thickness control
→There are three ice thicknesses: high ->medium ->low.
■Ice transparency control
→The ice transparency control function enables the production of clear ice.
■Auto cleaning
→ There are 2 cleaning modes: detergent and clean water; it is easy to control and use.
■Auto start
→With the auto start function, the auto startup time can be set between 1h and 24h.
■Low noise design
→ Highly efficient low-noise fan is adopted to offer a comfortable ice-making environment.
■Built-in LED
→ Built-in LED is used to clearly show status of the ice.
■Waterproof curtain design
→ A waterproof curtain is installed on the front of the ice sheet to prevent splash of water into the
products.

2
2. Product accessories
Inlet pipe joint 2EA
Drain pipe clamp 1EA
Inlet pipe 1EA
Drain pipe 1EA
Ice scoop 1EA
Leveling foot 4EA
User Manual 1EA
※Water purifier
It is recommended to use a water purifier (to be purchased
by the user), to improve ice quality and internal cleanliness
of the ice-maker.
■Check the following accessories before use.
■Please contact our aftersales services center if any of the following accessories is absent.

3
3. Product specifications
Item
Unit
Spec.
TIM-50A
TIM-75A
TIM-100A
Max. ice making mass
Kg/Day
50
75
100
Ice-making time
≤30
≤30
≤30
Dimensions
Height
mm
850
850
1010
Length
500
660
660
Width
640
640
640
Ice size
mm
22 x 22 x 22
22 x 22 x 22
22 x 22 x 22
Ice quantity per cycle
EA
55
90
126
Power supply
1-phase
115V 60Hz
115V 60Hz
115V 60Hz
Product weight
Pre-packing
Kg
45
52
65
Post-packing
65.5
76
82.5
Compressor
HP
1/3
1/3 +
1/2
Refrigerant
GAS
R404a
R404a
R404a
Condenser cooling mode
Air-cooled
Air-cooled
Air-cooled
Ice shape
Ice cube (CUBIC)
Ice cube (CUBIC)
Ice cube (CUBIC)
Operating temperature
°C
10~38
10~38
10~38
Power consumption
W
380
490
650
Temperature control
Electronic
Electronic
Electronic
Ice unloading control
Time controlled
Time controlled
Time controlled
Inlet pressure
psig
20~40
20~40
20~40
※It can realize the maximum ice-making mass at the ambient temperature and water temperature of 10 °C.
※It varies as ambient temperature changes and varies significantly in hot summer.

4
4. Product structure
Cabinet top
Back cover
Machine room
cover
Drain pipe
connector
Inlet pipe
connector
Power cord
Front View
Rear View
Door
Display panel
Controller
Condenser vent
Leveling foot
Side View
LED lamp
Inner container
Foam layer
(insulating layer)
PCB BOX
Compressor
Compressor base
Downpipe
Waterproof curtain
Evaporator (ice
sheet)
Unloading
transducer
Water Case
Water pump
Hot Gas valve
Condenser motor
Condenser

5
5. Installation
Please install it indoor.
Please install it on smooth and solid ground.
Outdoor installation may cause product damages and poor refrigerating results.
The product will produce vibration and noise on unsmooth ground.
Do not install it where there is hot air.
Do not place heavy objects or liquid containing containers
on the ice-maker.
Install it where there is no heating or heat generating equipment.
Do not install it where ambient temperature goes beyond the range of 10 °C
~38 °C .
Falling objects and flowing liquids may cause product damages, electric
leakage, etc.
Do not install it where it is humid or dusty.
Keep a 30 cm distance between its back and the wall to
facilitate troubleshooting and cooling.
.Environmental issues may cause electric leakage which consequently results in
fire and electric shock.
.Inlet/drain pipe close to the wall may lead to faults.
1) Unpacking and installation
1. Remove the transport case, tapes and packages. It may fail to run properly if any packaging material
is left on the ice-maker.
2. Take out the accessory box inside and install the leveling feet.
3. Install the ice-maker at the specified place. (See precautions for ice-maker installation position
specified below.)
4. Level the machine with installed leveling feet.
5. Check whether the power supply has the rated voltage. (Please use a leakage protector.)
6. Make sure to use a dedicated properly earthed socket. (Unearthed socket may cause faults and the
danger of electric shock.)

6
5. Installation
1. Permissible water pressure: 20~80 PSIG.
- Reduce water pressure through depressurization when inlet pressure is high.
2. For ice making, use clean water filtered with a water purifier.
- Direct use of tap water will produce scale which may block the pipeline and cause the ice-maker
to fail.
- For the water-cooled model, tap water can be directly used for cooling of the condenser.
3. To facilitate drainage, the height of the drainage port shall be <200 mm.
4. For the purpose of sanitation, the drain pipe shall not be directly connected to the drainage port.
Air-cooled model
Water-cooled model
Condenser
drain pipe
Condenser
inlet pipe
Drain
pipe for
ice-
making
Inlet pipe
for ice-
making
Drain
pipe for
ice-
making
Inlet pipe
for ice-
making
2) Connection of inlet pipe and drain pipe

7
6. Precautions for the use of power cord
7. Product earthing
■Please use earthed power outlet to prevent the danger of electric shock due to electric leakage.
■Separately connect a ground wire if an unearthed power outlet is used.
The earthing terminal is on the lower part at the back side of the product.
■Do not use a common power strip together with other equipment, but use a dedicated socket-outlet.
■Do not insert or unplug the power cord with wet hand, since there is the danger of electric shock.
●Power strip is among the causes of fire.
●Do not touch the power cord or plug with wet
hands.
Use a dedicated socket with earthing terminal.
There is no need for separate earthing.
Earthing terminal
Do not carry out earthing at the following places.
Do not contact water pipes, gas pipes, telephone
wires or lightning rods.
There is the hazard of explosion, fire, etc.
Gas pipe
There is the hazard of gas
explosion.
Telephone wire

8
8. Description of control panel
Icon
Button
Functions
Clean
Button for ice-maker cleaning; there are such functions as detergent cleaning, water
cleaning and drainage.
Auto start
The startup time can be set between 1h and 24h and for 6 stages.
Transparency control
There are 4 levels of transparency.
Ice thickness control
There are 3 ice thicknesses and the factory setting is medium (standard ice cube).
Start
It is used to start ice-making, end/cancel cleaning and set auto start.
1
3
6
12
18
24
1
2
3
Start button
Clean button
Transparency control button
Ice thickness control button
Auto start button
detergent
cleaning
Water cleaning
Drainage indicator
Timer indicator
Ice thickness
indicator
Unloading indicator
Fault indicator
Full indicator
Ice transparency
indicator
Ice-making indicator
1) Details of control panel
2) Functions of buttons on control panel

9
9. Basic operations of control panel
Function
Status Indicator
Details
Stage 1
Stage 2
Normal ice-making
Normal ice-making status
Normal unloading status
Bin full
Stop (unloading finished)
flash
Off when unloading is finished
Stop (promptly)
X10s
It promptly stops
Manual unloading
X10s
flash
Manual unloading
Ice thickness control
Produce small ice cubes
Produce standard ice cubes
Produce large ice cubes
Ice transparency control
~
Transparency not required/max. ice-
making mass
High transparency/min. ice-making mass
Medium transparency/medium ice-making
mass
Low transparency/max. ice-making mass
Auto start setting
It starts 1h later
~
~
It starts 24h later
Auto cleaning
Clean the machine with detergent
Clean the machine with clean water
Drainage sign
■With power ON, the following 3 icons will be displayed and this is the standby mode.
■The product shall be operated in standby mode.

10
10. Fault code identification
Fault Type
Identification
Status Description
Condenser sensor fault
Normally ON/flash
Condenser sensor fault
Drainage fault
Flash
Drainage fault or float switch fault
Temp. sensor
Normally ON/flash
Ambient temperature sensor fault
Temp. sensor
Flash
Ambient temperature sensor fails or ambient temperature
goes beyond normal operating temperature of the machine.
Ice-making fault
Normally ON/flash
Ice-making or float switch fault
Harvest fault
Normally ON/flash
Unloading failure or curtain switch fault
Water shortage (lack) fault
Flash
Water shortage (lack) fault

11
11. Operation of cleaning functions
1) Prepare the following items
- Detergent, disinfectant, cloth and rubber gloves
2) Precautions
- Remove scale in the water tank and pipeline before cleaning the ice-maker.
- Do not use toxic chemicals or bad substances.
- Paid services will be offered if the product is damaged due to the customer’s improper cleaning.
3) Preparations before cleaning
- Take out and store the ice cubes in advance since they may be contaminated during cleaning.
- Operate with power ON and the ice-maker in standby mode.
- Icons displayed in standby mode:
4) Method of cleaning with detergent (detergent cleaning -> clean water cleaning ->end)
Stage 1: Press the clean button and select detergent cleaning.
Stage 2: The detergent cleaning indicator is ON and 10s later the cleaning program starts.
Stage 3: With water intake finished, the detergent cleaning indicator starts to flash and the product enters the standby mode.
Now, add detergent or disinfectant.
Stage 4: With detergent or disinfectant added, press the clean button to restart the cleaning function.
Stage 5: The detergent cleaning program runs for 60min.
Stage 6: When the detergent cleaning program ends, the water cleaning stage starts and runs for another 60min.
Stage 7: With the above cleaning stages finished, the product automatically stops.
At any time: Press the power button during operation to cancel the cleaning task at any time.
5) Method of cleaning with clean water (clean water cleaning ->end)
Stage 1: Press the clean button and select clean water cleaning.
Stage 2: The clean water cleaning indicator is ON and 10s later the cleaning program starts.
Stage 3: The clean water cleaning program runs for 60min.
Stage 4: When the cleaning stage is finished, the product automatically stops.
At any time: Press the power button during operation to cancel the cleaning task at any time.
6) Drainage function
Stage 1: Press the clean button and select drainage.
Stage 2: The drainage indicator is ON and 10s later the drainage program starts.
Stage 3: The product stops when drainage is finished.
At any time: Press the power button during operation to cancel the drainage task at any time.
1阶段
清洗完成
2阶段
3阶段
4阶段
5阶段
6阶段
7阶段
1阶段
清洗完成
2阶段
3阶段
1阶段
排水完成
2阶段
3阶段
Detergent
Disinfectant
Stage 1
Stage 2
Stage 3
Stage 4
Stage 5
Stage 6
Stage 7
Cleaning end
Stage 1
Stage 2
Stage 3
Cleaning end
Stage 1
Stage 2
Stage 3
Drainage end

12
12. Verify before applying for aftersales repair!
Symptom
Verify
Actions to be Taken
It won’t start
1. Whether power is ON?
1. Connect the power supply.
2. Whether power switch is OFF?
2. Turn on the power switch.
3. Whether the supply voltage reaches the standard 220V
±10%?
3. Check the voltage and use the dedicated socket.
No water is supplied
1. Whether water valve is OFF?
1. Open the water supply valve.
2. Whether the water supply pipe is properly installed?
2. Properly install the water supply pipe.
3. Whether water supply is cut off?
3. Please wait if water supply is confirmed cut off.
4. Whether the water supply pump runs?
4. Contact the aftersales services center after verification.
It won’t make ice
1. Whether bypass of the downpipe is blocked?
1. Remove foreign matters at bypass of the downpipe.
2. Whether water is supplied?
2. Check whether water supply is proper.
3. Whether the compressor runs properly?
3. Contact the aftersales services center after verification.
4. Whether there is dust on the sensor for air cooling and
whether ventilation is smooth?
4. Remove dust on the front electric pump.
5. Whether the condenser fan motor runs?
5. Contact the aftersales services center after verification.
6. Whether there are heating appliances near it?
6. Keep it away from heating appliances.
7. Whether water supply is insufficient or there is not
sufficient water in the water tank?
7. Contact the aftersales services center if water supply is
normal.
Overcooling
1. Whether ambient temperature is below 10 °C?
1. Do not use it when ambient temperature is below 10 °C.
2. Whether water is insufficient?
2. Insufficient water will cause overcooling.
Adjust the water supply volume.
Abnormal noise or loud noise
1. Whether the installation site is uneven or unsolid?
1. Make the ground smooth.
2. Whether the front or back of the ice-maker touches the
wall?
2. Keep a space of at least 50 cm at both the front and the
back.
Water accumulates in the ice
bin
1. Whether there are foreign matters in the drain pipe?
1. Remove foreign matters in the drain pipe.
Please verify!
Verify the above contents before applying for aftersales repair and contact us after verification:
13. 售后服务指南
The faults do not cover the following problems:
■A small amount of water is splashed into inner container of the product.
■The product shakes slightly when it is started.