TURBRO In-Flames INF50W-3D User manual

IMPORTANT
READ ALL INSTRUCTIONS BEFORE USING YOUR
ELECTRIC FIREPLACE. FAILURE TO FOLLOW
INSTRUCTIONS MAY LEAD TO DAMAGE TO THE
MACHINE OR PERSONAL INJURY.
KEEP THIS USER MANUAL FOR FUTURE
REFERENCE.
MODEL NO: INF50W-3D
INF60W-3D

Tips for First-Time Use
Safety Instructions
Specifications
Parts List
Dimensions
Electrical Safety
Wiring
Testing
Installation
A. Recessed Installation
B. Wall-mounted installation
Operation
Control Panel Operation
Remote Control Operation
FCC Warning
...........................................................................
..................................................................................
..........................................................................................
..................................................................................................
..............................................................................................
......................................................................................
.....................................................................................................
....................................................................................................
...............................................................................................
........................................................................
..................................................................
.................................................................................................
........................................................................
.....................................................................
............................................................................................
01
01
02
03
04
05
05
08
08
09
13
17
17
20
23
Contents

Cleaning & Maintenance
Troubleshooting
Warranty Information
Warranty Registration
........................................................................
......................................................................................
..............................................................................
.............................................................................
24
25
26
26
Contents

01
Tip for First-Time Use
Safety Instructions
When using this fireplace for the first time, or after a long period of storage, let the fireplace run for at least 15 minutes
with the thermostat set at the maximum heat level to remove the "new product" smell. This smell is because the fireplace
absorbs moisture, creating an odor similar to that of old leather. It will go away after a few minutes of use.
Please read the following instructions before attempting to assemble, operate, or install this product.
• Do not use this product outdoors. This product is for indoor use only.
• This product is not intended for use in bathrooms, laundry areas, and similar indoor locations. Do not place this product
where it may fall into a bathtub or other water container.
• This product is hot when in use. Keep combustible materials such as furniture, pillows, bedding, papers, clothes, and
curtains at least 3ft (0.9m) from the hot air outlet.
• Do not run the power cord of this product under carpeting, throw rugs, runners, or similar items. Arrange the cord away
from high-traffic areas so it will not be tripped over.
• Extreme caution is required when the product is used near children or invalids and whenever = left unattended.
• Do not operate this product with a damaged power cord or plug, after the appliance malfunctions, or the product is
damaged. Any repairs to this appliance should be carried out by a qualified service person.
• Under no circumstances should this product be modified. Parts removed for service must be replaced prior to using this
product.
• Connect to properly grounded power outlets only.
• Always plug the fireplace directly into a wall outlet. An extension cord, outlet, or power strip should never be used with
this product.
• This product, when installed, must be electrically grounded in accordance with local electrical codes. For the USA:
National Electric Code, ANSI/NFPA No. 70. For Canada: CSA C22.1 Canadian Electrical codes.
• To disconnect this product, turn the product off, then remove the power plug from the outlet.
• Always unplug this product if you do not plan to use it for a long period of time.
• Do not insert or allow foreign objects to enter any ventilation or exhaust openings as this may cause an electric shock,
fire, or damage to the appliance.
• To prevent a possible fire, do not block air intakes or exhausts in any manner. Do not use it on soft surfaces, like a bed,
where the opening may be blocked.
• The fireplace has hot, sparking, and arcing parts inside. Do not use it in areas where gasoline, paint, or flammable
liquids are used or stored. This appliance should not be used as a drying rack for clothing.
• Use this appliance only as described in this manual. Any other use not recommended by the manufacturer may cause
fire, electric shock, or personal injury.
• This product can expose you to toxic chemicals including Di(2-ethylhexyl)
phthalate (DEHP), which may cause cancer or harm developmental growth.
• Wash hands after installation.
For more information go to www.p65Warnings.ca.gov
CAUTION

02
Specifications
• This heater has an overheating protection cutoff that switches the appliance off automatically if it overheats.
• Obstruction of the front grill may result in overheating. If this occurs, please disconnect the heater from the power socket
and allow it to cool for 10-15 minutes before powering it on again.
• Should problems persist, please contact TURBRO customer service team via [email protected].
Overheating Protection
Power Supply
Rated Current
Rated Power
Adjustable Thermostat
Noise Level (dBA)
Timer
LED Lighting Effect
Remote Control
APP Control
110-120V / 60Hz
12.5A
1500W
60°F - 99°F
≤ 42 dBA
30 min. - 12 hrs
LED
Yes
Yes

03
Hardware Contents
Parts List
Description
Mounting Bracket A
Mounting Bracket B
Acrylic Crystals
Logs
Quantity
1
1
1
1
Part
E
F
G
H
Description
Firefox
Glass Panel
Remote Control
Ember Bed Strip
Quantity
1
1
1
1
Part
A
B
C
D
Description
Wall Anchor
Large Screw
Small Screw
Quantity
4
6
12
Part
AA
BB
CC
A B
C D E
F G H
AA BB CC

04
Dimensions
TURBRO INF50W-3D Dimensions
TURBRO INF60W-3D Dimensions
Front view
Top view
Side view
Front view
Top view
Side view

05
Electrical Safety
• This fireplace can either be plugged into a grounded 3-prong outlet or hard wire connection.
• A 15-amp, 120-volt, 60 Hz circuit with a properly grounded outlet is required. Preferably, the item will be on a dedicated
circuit. Having other appliances on the same circuit may cause the circuit breaker to trip or the fuse to blow while the
product is in operation.
• This product is equipped with a polarized plug where one prong is wider than the other. For your safety, please insert
the plug correctly. If you are unable to insert the plug into the electrical outlet try reversing the plug. If the plug still does
not fit, contact a qualified electrician.
• This product, when installed, must be electrically grounded in accordance with local electrical codes. For the USA:
National Electric Code, ANSI/NFPA No. 70. For Canada: CSA C22.1 Canadian Electrical codes.
• Do not operate this product with a damaged power cord or plug, after the appliance malfunctions, or the product is
damaged. Any repairs to this appliance should be carried out by a qualified service person. Immediately call a qualified
service technician to inspect the item and replace any part of the electrical system which has been underwater.
This fireplace can either be plugged into a grounded 3-prong outlet or a hard wire connection.
Wiring
US 3-Pin Polarized Plug
• Due to high temperatures, keep the fireplace out of high-traffic locations.
• Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3ft (0.9m) away
from the front of the fireplace.
• Never install the fireplace where it may fall into a bathtub or other body of water.
• Prevent contact with loose insulation. Do not install the fireplace against a vapor barrier or exposed insulation.
• Do not expose the fireplace to the elements (rain, etc).
WARNINGS
• Phillips screwdriver
• Level
• Tape measure
• Electric power drill
Tools Required (not included)

06
This product is equipped with a 3-pin polarized plug.
Connect to properly grounded outlets only. This unit is for use on 120 volts outlets only. For your safety, please always
plug the unit into a wall outlet/receptacle. An extension cord or power tap (outlet/power strip) should never be used with
this device.
WARNING: If it is necessary to hard wire this appliance, a qualified electrician will be required to remove the cord
connection and wire the appliance directly to the household wiring. The wire and power supply breaker must be rated for
120V minimum 15 amps.
This appliance must be electrically connected and grounded in accordance with local codes, if hard wired. In the absence
of local codes, use the current CSA C22.1 CANADIAN ELECTRICAL CODE in Canada or the current ANSI/NFPA 70
NATIONAL ELECTRICAL CODE in the United States.
1. Remove the 2 pcs screws to release the cover of the junction box, which is located on the top left side of the appliance.
2. Pull the junction box out. loosen the screws in the terminal block to release the wires of the power cord.
Hard Wire Connection

07
5. Reinstall the junction box back.
6. Save the power cord.
4. Insert the White wire to the designated N Terminal and tighten the screw.
Insert the Green or bare copper wire to the designated G Terminal and tighten the screw.
Insert the Black wire to the designated L Terminal and tighten the screw.
Make sure all connections are tightened properly.
3. Use pliers to take the wire clip off and remove the power cord.
WHITE/BLANC (N)
BLACK/NOIR (L)
GREEN/VERT (G)
WHITE/BLANC (N)
BLACK/NOIR (L)
GREEN/VERT (G)
FIREPLACE JUNCTION
POWER SUPPLY

08
Bottom
Sides
Back
Top
Front
6”
0”
0”
8” to mantel
8” to TV
8” to ceiling
36”
Installation
• Measure wall location to ensure that fireplace will fit on desired wall location.
• Minimum clearances (measurements taken from front of glass panel):
Choosing Installation Location
Testing the Fireplace Prior to Installation
NOTE: Do not install the glass panel when testing.
• Before installing the fireplace, test the fireplace to make sure that it operates properly.
• Plug fireplace into approved outlet and power on the fireplace. Once fireplace is tested, continue with the installation.
• If you have any problems, please contact technical support [email protected].
Testing

A. Recessed Installation
• Due to many different finish materials used on walls, it is highly recommended that you consult a local builder before
you install this fireplace in the wall.
• In order to avoid the possibility of exposed insulation or vapor barrier coming in contact with the fireplace, it is
recommended that the walls of the fireplace enclosure be “finished” (Sheetrock, drywall, etc) as you would finish any
other wall of your home. This will ensure that clearance to combustibles is maintained within the wall cavity.
• Never install the fireplace into load-bearing walls. When recessing fireplace in a wall, recess into non-load bearing
walls ONLY!
1. Choose a location in the wall to install fireplace.
2. Create opening in the wall that is no more than ¼” larger than metal firebox portion of fireplace. And create a rough-in
with electrical supply, the electrical junction box is located on the left side, at the back of the appliance.
Confirm the location before recessed fireplace
09
NOTE:
• Before installing the fireplace, please plug fireplace into approved outlet and power on, test the fireplace to make sure
that it operates properly.
• Do not install the glass panel when testing.
• If you have any problems about installation, please contact support team at [email protected].
Side View (Wall Mount )
8" (203mm)
6" (152mm) 6" (152mm)
Mantel
Floor
Wall
Side View (recessed into a wall)
8" (203mm)
0"
Mantel
Floor

10
Length A
47-19/20” / 1218mm
57-19/20” / 1472mm
Depth C
4-1/2” / 114mm
4-1/2” / 114mm
Height B
16-1/4” / 413mm
16-1/4” / 413mm
Model
INF50W-3D
INF60W-3D
3. Fix the Mounting Brackets on both sides of the rebox using 6 Small Bolts (CC) as shown.
FE
A
A
B
C
Note: The hook hole of the Mounting Bracket does on the front of the fireplace.

11
4. Insert the Firebox into the opening and adjust the position of the unit until it is centered and level.
5. Attach the Firebox with 4 Large Screws (BB), on the side wood studs with an electric drill.
BB

7. Installing the Glass Panel.
NOTE: This glass front is heavy. It is recommended that two people perform the assembly at this step to prevent damage.
• Carefully set both hooks of the front glass panel in the firebox.
NOTE: Make sure the glass is properly installed according to the direction and steps below, and fully attached to the
firebox so that the control panel can work properly.
12
6. Insert the Ember Bed Strip (D) into the base of the Firebox (A).
Depending on your preference, place Acrylic Crystals (G) / Log (H) on the Carbon Bed Strip (D).
G
H
D

13
• Secure the glass front (B) by fastening 4 Small Screw (CC) and complete the installation.
Your fireplace is now ready for use!
A1
48-27/64” / 1230mm
58-27/64” / 1484mm
B1
5-5/16” / 135mm
5-5/16” / 135mm
Model
INF50W-3D
INF60W-3D
B.Wall-mounted installation
1. To mount the item to the wall, refer to the mounted size of the model below and mark the mounting position on the wall.
Using a 1/4-inch electric drill bit (not included), drill a pilot hole at each of the marked corners.

14
3. Insert Wall Anchors (AA) to drilled holes, then insert
Large Screws (BB) into the Wall Anchor (AA) with
an electric drill or screwdriver.
Note: Wall Anchors (AA) are not required if you are
installing the fireplace directly to studs. It is recommended
to install the mounting brackets to at least one stud if
possible.
WALL
Note: Do not fasten the Large Screws (BB) tightly. Leave 1/4”(6mm) spacing to hang up the Firebox.
1/4" (6mm)
2. Fix the Mounting Brackets at both sides of firebox by 6 Small Screws (CC) as shown.
Note: The hook hole of the Mounting Bracket is on the back.
A
E
F
BB

15
4. Lift the Firebox(A) and hang the Firebox on to the wall with the Large Screws (BB).
(It’s recommended that two people lift the firebox to prevent injury or damage)
5. Insert the Ember Bed Strip (D) into the base of the Firebox (A).
Depending on your preference, place Acrylic Crystals (G) / Log (H) on the Carbon Bed Strip (D).
A
BB
E
A
D
A
G
H

16
6. Installing the Glass Panel.
NOTE: This glass front is heavy. It is recommended 2 people to fulfill the assembly at this step to prevent damage.
• Carefully set both hooks of the front glass panel in the firebox.
NOTE: Make sure the glass is properly installed according to the direction and steps below, and fully attached to the
firebox so that the control panel can work properly.
• Secure the glass front (B) by fastening 4 Small Screw (CC) and complete the installation.
Your fireplace is now ready for use!

Display Value
F01
F02
F03
F04
F05
F06
F07
F08
F09
F10
F1
F12
OFF
Flame Color
Orange
Blue
Green
Orange + Blue
Orange + Green
Blue + Green
Orange + Blue + Green
Orange & Blue
Orange & Green
Blue & Green
Orange & Blue & Green
Gradient
OFF
Operation
The Control Panel is located in the lower right corner of the fireplace. The function icon lights will turn off after 20 seconds
of no operation. Please touch the control panel to wake it up again before using the control panel.
Power Button
• Turn the appliance ON/ OFF.
Flame Button
• Press the Flame Button to active the Flame Color mode.
• Press again to cycle through different colors of the flame. See the table for more detailed information.
Control Panel Operation
17
Display Screen REC Heater Ember Bed Power
FlameFlame SpeedCrackling Sound