Turnstiles KT-2 User manual

Before you begin
Before you install the controller, check that the product box
contains the following items:
• One KT-2 Two-Door Controller
• One accessories kit
•KT-2 Two-Door Controller Installation Guide
Operating modes
Use the KT-2 controller in one of the following modes:
• Stand-alone mode: use as a stand-alone controller with direct
configuration. This does not require any software.
• EntraPass mode: use with EntraPass access control software to
connect to additional doors and controllers.
Installing and powering the KT-2
Power the KT-2 in one of the following ways:
• Use power over Ethernet (PoE).
• Use power over Ethernet plus (PoE+).
• Connect an external power supply to the 12 VDC input.
To install and power the KT-2, refer to the Installation and Powering
the KT-2 sections of the KT-2 Two-Door Controller Installation Guide.
Connection and configuration
Wired controller
1. To connect the controller, refer to the KT-2 Two-Door Controller
Installation Guide.
2. To configure the controller, complete Configuring the KT-2
using the registration page.
Wireless controller
• To connect and configure the controller, complete Connecting
and configuring a wireless controller.
Configuring the KT-2 using the registration page
1. Connect the controller to your preferred network using the
Ethernet port.
2. On your computer or mobile device, open a web browser.
Note: If you use a mobile device, connect it to a wireless
network that has access to the wired network subnet.
3. In the address bar, type one of the following options:
- Type the IP address of the KT-2 controller. This is the
preferred option. To find the controller's IP address, you
can use the KT-Finder.
- Type KT-XX-XX-XX where XX-XX-XX is the last six digits of
the controller's Ethernet MAC address.
Note: The KT-2 controller and the device you use to
access the registration page must be on the same
network. If either of the devices are behind a bridged
network, even if they have the same subnet, this cannot
work.
4. On the KT-2 REGISTRATION page, in the upper right of the
window, select your preferred language. English is selected by
default.
5. To configure the correct mode, complete the steps in one of
the following procedures:
- To configure the controller in stand-alone mode,
complete one of the following options:
-Configuring stand-alone mode using the activate
now option
-Configuring stand-alone mode using an
activation code
- To configure the controller in EntraPass mode, complete
Configuring EntraPass mode for a wired controller.
Configuring stand-alone mode using the activate now
option
1. On the KT-2 REGISTRATION page, click Activate now.
2. On the Activate now tab, in the Customer information and
Installer information fields, type the relevant information.
3. Click Activate now.
Configuring stand-alone mode using an activation code
1. Go to http://www.kantech.com.
2. Click Support and click Kantech Registration.
3. In the KT Standalone Registration area, click Click here.
4. On the KTWeb - Registration page, type the relevant
information and click Register. You receive an activation code
by email. Alternatively, contact Kantech technical support in
your region to get an activation code.
5. Go to the KT-2 REGISTRATION page and click Other ways to
activate.
6. In the Activation code field, type the activation code, and
click Activate now.
Configuring EntraPass mode for a wired controller
1. On the KT-2 REGISTRATION page, click EntraPass.
2. In the EntraPass gateway pane, in the IP address field, type
the IP address, or in the Domain name field, type the domain
name.
3. From the Protocol list, select TCP or UDP.
4. Optional: If you select UDP, in the Port field, type the port
number.
5. Click Submit.
Connecting and configuring a wireless controller
You can connect the KT-2 over Wi-Fi only when you use the
controller in EntraPass mode and power it with a KT-PS4085 power
supply.
1. On a laptop or mobile device, go to the Wi-Fi settings.
2. From the list of available wireless networks, select the access
point (AP) name (SSID) of the controller. The AP name of the
controller appears as KT2-XX-XX-XX. XX-XX-XX represents
the last six digits of the AP MAC address printed on the KT-2
backplane label.
3. Clear the Connect automatically check box and click
Connect.
4. In the Enter the network security key field, type the
password. The default password is TYCO1234.
5. Click Next and check your connection status.
6. On a web browser address bar, type the following IP address:
192.168.240.1/jciprov.html. Press Enter.
7. On the Web Provisioning page, from the Please Select
Country list, select a country.
KT-2 Two-Door Controller Quick Start Guide
2021-06-28
D29010686R001
D29010686R001
www.TURNSTILES.us | EntraPASS.com | [email protected] | 303-670-1099

Note: To change the selected country after you complete
the configuration, you must factory default the controller.
All saved settings and data are lost when you factory
default the controller.
Note: The list of supported countries may vary
depending on regulatory and standards updates.
8. In the Wireless Network pane, click Select Network from
List and select the appropriate network, or click Manually
and type the name of the network if it is hidden.
9. In the Password field, type the network password.
10. In the EntraPass gateway pane, click EntraPass IP address,
and type the direct IP address. Alternatively, leave the IP
address as 0.0.0.0 if you want to enroll the controller using
the KT-Finder or the One Button.
Note: To avoid connectivity issues, ensure that the
controller and the gateway are on the same subnet, and
that all the required ports are open in the firewall.
11. From the Protocol list, select TCP or UDP. Before you
configure the protocol, ask your network administrator about
the firewall rules for communicating over your selected
protocol.
12. Optional: If you select UDP, in the Port field, type the port
number. Before you configure the port, ask your network
administrator about the firewall rules for ports.
13. Click Submit.
• If the controller succeeds in joining the selected wireless
network, the Wi-Fi LED turns on and is solid yellow.
• If the controller fails to connect, the Wi-Fi LED stays off. The
controller attempts to connect three times before returning to
AP mode (factory default).
• If static IP mode is not supported in Wi-Fi, the Wi-Fi LED turns
off.
Setting up the KT-2 using the wizard
To set up the KT-2, complete the steps in the wizard.
Entering credentials
1. Click Installer or Operator.
2. Click Next Step.
3. In the Password field, type a new password. The password
must contain a minimum of 8 characters and include a
lowercase letter, an uppercase letter, a number, and a special
character.
Note: You cannot retrieve a forgotten password. If
you forget your password, you must factory default
the controller. For information about how to factory
default the controller, refer to the KT-2 Two-Door Controller
Installation Guide.
Setting the date and time
• Configure the Date, Date format, Hour, and Time zone, and
click Next Step.
Formatting cards
1. From the Reader Type list, select the card reader type.
2. In the Card Format field, type the card format. The default
format is HHHH:DDDDD.
3. In the Number of PIN digits field, type or select the PIN
length.
4. Optional: Select the Allow PIN duplication check box.
5. Click Next Step.
Configuring doors
1. In the Door name field, type the door name.
2. For ioSmart card readers, in the Serial number field, type
the serial number of the entry card reader and type the serial
number of the exit card reader.
3. Select the Door Contact input and REX input check boxes.
4. Select Fail safe or Fail secure, and click Next Step.
5. On the Summary & Backup window, review the information
and click Save.
www.TURNSTILES.us | EntraPASS.com | [email protected] | 303-670-1099