TUYA QS-WIFI-C01 User manual

Wi-Fi Curtain Module
QS-WIFI-C01
Mounting Clip
INSTRUCTION MANUAL
Reset Key
EMC Standard (EMC)
EN 300 328 V2.1.1 (2016-11),
EN 301489-1 V2.1.1 (2017-02),
EN 301489-17 V3.1.1 (2017-02),
EN 62311: 2008, EN 61000-6-1:2007,
EN 61000-6-3:2007+A1:2011
Safety Standard (LVD)
IEC 60669-2-1:2002/AMD1:2008/
AMD2:2015, IEC 60669-1:1998/
AMD1:1999/AMD2:2006,
EN 60669-2-1:2004+A1: 2009+ A2:2010,
EN 60669-1:2018
RoHS Standard (RoHS)
2011/65/EU, (EU) 2015/863
Radio Equipment (RED)
ETSI EN 300 328 V2.1.1 (2016-11)
TECHNICAL SPECIFICATIONS
Product type Wi-Fi Curtain Module
Voltage 220-240V AC 50/60Hz
Current 3A
WiFi frequency 2.4GHz - 2.4835GHz WIFI
Operation temp. -10C - +40C
Case temp. Tc: +80C (Max.)
Operation range ≤ 200 m
Dims (WxDxH) 46x46x18mm(without clip)
IP rating IP20
Warranty 3 years
3. Keep the device away from water , damp or hot
environment.
4. Install the device away from strong signal sources
such as mic rowave oven that may cause signal
interruption resulted to abnormal operation of the
device.
5. Obstruction by concrete wall or metallic
materials may reduce the effective operation
range of the device and should be avoided.
6. Do NOT attempt to disassemble,repair or modify
the device.
FAQ
Q1: What should I do if I can’t congure the Curtain
module?
a. Please check whether device is powered on.
b. Make sure your mobile and Curtain module
are under the same 2.4 Ghz WIFI network.
c. Whether it’s in good internet conditions.
d. Make sure the password entered in App is correct.
e. Make sure the wiring is correct.
Q2: Which products can I control with the device?
Q3: What happens if the WIFI goes off?
Curtain,shutter, blind.....
You can still control the device connected the Curtain
module with your traditional Curtain and once WIFI is
active again the device connected to module will
connect automatically to your WIFI network.
Q4: What should I do if I change the WIFI network or
change the password?
You can connect the module to the WIFI network
according to the App User Manual.
Q 5: How do I reset the device?
Power on/off device 5 times or press the reset key for
about 10 seconds until the beeper on the module sound
continuously.
with mounting clip without mounting clip
50mm
46mm
22.5mm
18mm
46mm
46mm
Wiring Instructions and Diagrams
1.Turn off the power supply before carrying out any
electrical installation work.
2. Connect wires according to the wiring diagram.
3. Insert the module into the junction box.
4. Connect the power supply and follow
Curtain module
conguration instructions.
Notes: Take your smartphone close to the Curtain
sure you have min. 50% Wi-Fi signal.
Global international operation Whenever & Wherever
You are,All-in-one Mobile App
Anywhere
APP
APP
Voice control-work
with google home Voice control-work with Amazon Alexa Device Sharing
Apps
APP
Router Voice control Curtain Switch
Inhouse local operation
NL
LN
M
Scan the QR code to download Tuya Smart App, or
you can also search keyword “Tuya Smart” at App
Store or Googleplay to download App.
IOS APP / Android APP
APP USER MANUAL
INSTALLATION
Warnings:
1.
electrician in accordance with local regulations.
2. Keep the device out of reach of children.
MANUAL OVERRIDE
The Curtain module terminal reserves the access of
manual override function for the end-user to switch on/off.
· If you have connected the wall push-button, check
its work. Single pressing ofthe "down" button / "up"
button, will cause that the roller shutters moves in
the desired direction to the end position. If the ele-
ctric shutter goes in the opposite direction to the
expected,select "motor reversal" in the "More"op-
tion. When the electric shutter is moving up, press-
ing "up" button switches causes that the shutter
will stop immediately; when the electric shutter is
moving down, pressing "down" button switches
causes that the shutter will stop immediately.
Notes:
1) Both the adjustment on App and
Curtain can overwrite
each other, the last adjustment remains in memory.
2) The App control is synchronized with the
manual switch.

Wi-Fi Curtain Module
QS-WIFI-C01
Mounting Clip
INSTRUCTION MANUAL
Reset Key
EMC Standard (EMC)
EN 300 328 V2.1.1 (2016-11),
EN 301489-1 V2.1.1 (2017-02),
EN 301489-17 V3.1.1 (2017-02),
EN 62311: 2008, EN 61000-6-1:2007,
EN 61000-6-3:2007+A1:2011
Safety Standard (LVD)
IEC 60669-2-1:2002/AMD1:2008/
AMD2:2015, IEC 60669-1:1998/
AMD1:1999/AMD2:2006,
EN 60669-2-1:2004+A1: 2009+ A2:2010,
EN 60669-1:2018
RoHS Standard (RoHS)
2011/65/EU, (EU) 2015/863
Radio Equipment (RED)
ETSI EN 300 328 V2.1.1 (2016-11)
TECHNICAL SPECIFICATIONS
Product type Wi-Fi Curtain Module
Voltage 220-240V AC 50/60Hz
Current 3A
WiFi frequency 2.4GHz - 2.4835GHz WIFI
Operation temp. -10C - +40C
Case temp. Tc: +80C (Max.)
Operation range ≤ 200 m
Dims (WxDxH) 46x46x18mm(without clip)
IP rating IP20
Warranty 3 years
3. Keep the device away from water , damp or hot
environment.
4. Install the device away from strong signal sources
such as mic rowave oven that may cause signal
interruption resulted to abnormal operation of the
device.
5. Obstruction by concrete wall or metallic
materials may reduce the effective operation
range of the device and should be avoided.
6. Do NOT attempt to disassemble,repair or modify
the device.
FAQ
Q1: What should I do if I can’t congure the Curtain
module?
a. Please check whether device is powered on.
b. Make sure your mobile and Curtain module
are under the same 2.4 Ghz WIFI network.
c. Whether it’s in good internet conditions.
d. Make sure the password entered in App is correct.
e. Make sure the wiring is correct.
Q2: Which products can I control with the device?
Q3: What happens if the WIFI goes off?
Curtain,shutter, blind.....
You can still control the device connected the Curtain
module with your traditional Curtain and once WIFI is
active again the device connected to module will
connect automatically to your WIFI network.
Q4: What should I do if I change the WIFI network or
change the password?
You can connect the module to the WIFI network
according to the App User Manual.
Q 5: How do I reset the device?
Power on/off device 5 times or press the reset key for
about 10 seconds until the beeper on the module sound
continuously.
with mounting clip without mounting clip
50mm
46mm
22.5mm
18mm
46mm
46mm
Wiring Instructions and Diagrams
1.Turn off the power supply before carrying out any
electrical installation work.
2. Connect wires according to the wiring diagram.
3. Insert the module into the junction box.
4. Connect the power supply and follow
Curtain module
conguration instructions.
Notes: Take your smartphone close to the Curtain
sure you have min. 50% Wi-Fi signal.
Global international operation Whenever & Wherever
You are,All-in-one Mobile App
Anywhere
APP
APP
Voice control-work
with google home Voice control-work with Amazon Alexa Device Sharing
Apps
APP
Router Voice control Curtain Switch
Inhouse local operation
NL
LN
M
Scan the QR code to download Tuya Smart App, or
you can also search keyword “Tuya Smart” at App
Store or Googleplay to download App.
IOS APP / Android APP
APP USER MANUAL
INSTALLATION
Warnings:
1.
electrician in accordance with local regulations.
2. Keep the device out of reach of children.
MANUAL OVERRIDE
The Curtain module terminal reserves the access of
manual override function for the end-user to switch on/off.
· If you have connected the wall push-button, check
its work. Single pressing ofthe "down" button / "up"
button, will cause that the roller shutters moves in
the desired direction to the end position. If the ele-
ctric shutter goes in the opposite direction to the
expected,select "motor reversal" in the "More"op-
tion. When the electric shutter is moving up, press-
ing "up" button switches causes that the shutter
will stop immediately; when the electric shutter is
moving down, pressing "down" button switches
causes that the shutter will stop immediately.
Notes:
1) Both the adjustment on App and
Curtain can overwrite
each other, the last adjustment remains in memory.
2) The App control is synchronized with the
manual switch.

Wi-Fi Curtain Module
QS-WIFI-C01
Mounting Clip
INSTRUCTION MANUAL
Reset Key
EMC Standard (EMC)
EN 300 328 V2.1.1 (2016-11),
EN 301489-1 V2.1.1 (2017-02),
EN 301489-17 V3.1.1 (2017-02),
EN 62311: 2008, EN 61000-6-1:2007,
EN 61000-6-3:2007+A1:2011
Safety Standard (LVD)
IEC 60669-2-1:2002/AMD1:2008/
AMD2:2015, IEC 60669-1:1998/
AMD1:1999/AMD2:2006,
EN 60669-2-1:2004+A1: 2009+ A2:2010,
EN 60669-1:2018
RoHS Standard (RoHS)
2011/65/EU, (EU) 2015/863
Radio Equipment (RED)
ETSI EN 300 328 V2.1.1 (2016-11)
TECHNICAL SPECIFICATIONS
Product type Wi-Fi Curtain Module
Voltage 220-240V AC 50/60Hz
Current 3A
WiFi frequency 2.4GHz - 2.4835GHz WIFI
Operation temp. -10C - +40C
Case temp. Tc: +80C (Max.)
Operation range ≤ 200 m
Dims (WxDxH) 46x46x18mm(without clip)
IP rating IP20
Warranty 3 years
3. Keep the device away from water , damp or hot
environment.
4. Install the device away from strong signal sources
such as mic rowave oven that may cause signal
interruption resulted to abnormal operation of the
device.
5. Obstruction by concrete wall or metallic
materials may reduce the effective operation
range of the device and should be avoided.
6. Do NOT attempt to disassemble,repair or modify
the device.
FAQ
Q1: What should I do if I can’t congure the Curtain
module?
a. Please check whether device is powered on.
b. Make sure your mobile and Curtain module
are under the same 2.4 Ghz WIFI network.
c. Whether it’s in good internet conditions.
d. Make sure the password entered in App is correct.
e. Make sure the wiring is correct.
Q2: Which products can I control with the device?
Q3: What happens if the WIFI goes off?
Curtain,shutter, blind.....
You can still control the device connected the Curtain
module with your traditional Curtain and once WIFI is
active again the device connected to module will
connect automatically to your WIFI network.
Q4: What should I do if I change the WIFI network or
change the password?
You can connect the module to the WIFI network
according to the App User Manual.
Q 5: How do I reset the device?
Power on/off device 5 times or press the reset key for
about 10 seconds until the beeper on the module sound
continuously.
with mounting clip without mounting clip
50mm
46mm
22.5mm
18mm
46mm
46mm
Wiring Instructions and Diagrams
1.Turn off the power supply before carrying out any
electrical installation work.
2. Connect wires according to the wiring diagram.
3. Insert the module into the junction box.
4. Connect the power supply and follow
Curtain module
conguration instructions.
Notes: Take your smartphone close to the Curtain
sure you have min. 50% Wi-Fi signal.
Global international operation Whenever & Wherever
You are,All-in-one Mobile App
Anywhere
APP
APP
Voice control-work
with google home Voice control-work with Amazon Alexa Device Sharing
Apps
APP
Router Voice control Curtain Switch
Inhouse local operation
NL
LN
M
Scan the QR code to download Tuya Smart App, or
you can also search keyword “Tuya Smart” at App
Store or Googleplay to download App.
IOS APP / Android APP
APP USER MANUAL
INSTALLATION
Warnings:
1.
electrician in accordance with local regulations.
2. Keep the device out of reach of children.
MANUAL OVERRIDE
The Curtain module terminal reserves the access of
manual override function for the end-user to switch on/off.
· If you have connected the wall push-button, check
its work. Single pressing ofthe "down" button / "up"
button, will cause that the roller shutters moves in
the desired direction to the end position. If the ele-
ctric shutter goes in the opposite direction to the
expected,select "motor reversal" in the "More"op-
tion. When the electric shutter is moving up, press-
ing "up" button switches causes that the shutter
will stop immediately; when the electric shutter is
moving down, pressing "down" button switches
causes that the shutter will stop immediately.
Notes:
1) Both the adjustment on App and
Curtain can overwrite
each other, the last adjustment remains in memory.
2) The App control is synchronized with the
manual switch.

Wi-Fi Curtain Module
QS-WIFI-C01
Mounting Clip
INSTRUCTION MANUAL
Reset Key
EMC Standard (EMC)
EN 300 328 V2.1.1 (2016-11),
EN 301489-1 V2.1.1 (2017-02),
EN 301489-17 V3.1.1 (2017-02),
EN 62311: 2008, EN 61000-6-1:2007,
EN 61000-6-3:2007+A1:2011
Safety Standard (LVD)
IEC 60669-2-1:2002/AMD1:2008/
AMD2:2015, IEC 60669-1:1998/
AMD1:1999/AMD2:2006,
EN 60669-2-1:2004+A1: 2009+ A2:2010,
EN 60669-1:2018
RoHS Standard (RoHS)
2011/65/EU, (EU) 2015/863
Radio Equipment (RED)
ETSI EN 300 328 V2.1.1 (2016-11)
TECHNICAL SPECIFICATIONS
Product type Wi-Fi Curtain Module
Voltage 220-240V AC 50/60Hz
Current 3A
WiFi frequency 2.4GHz - 2.4835GHz WIFI
Operation temp. -10C - +40C
Case temp. Tc: +80C (Max.)
Operation range ≤ 200 m
Dims (WxDxH) 46x46x18mm(without clip)
IP rating IP20
Warranty 3 years
3. Keep the device away from water , damp or hot
environment.
4. Install the device away from strong signal sources
such as mic rowave oven that may cause signal
interruption resulted to abnormal operation of the
device.
5. Obstruction by concrete wall or metallic
materials may reduce the effective operation
range of the device and should be avoided.
6. Do NOT attempt to disassemble,repair or modify
the device.
FAQ
Q1: What should I do if I can’t congure the Curtain
module?
a. Please check whether device is powered on.
b. Make sure your mobile and Curtain module
are under the same 2.4 Ghz WIFI network.
c. Whether it’s in good internet conditions.
d. Make sure the password entered in App is correct.
e. Make sure the wiring is correct.
Q2: Which products can I control with the device?
Q3: What happens if the WIFI goes off?
Curtain,shutter, blind.....
You can still control the device connected the Curtain
module with your traditional Curtain and once WIFI is
active again the device connected to module will
connect automatically to your WIFI network.
Q4: What should I do if I change the WIFI network or
change the password?
You can connect the module to the WIFI network
according to the App User Manual.
Q 5: How do I reset the device?
Power on/off device 5 times or press the reset key for
about 10 seconds until the beeper on the module sound
continuously.
with mounting clip without mounting clip
50mm
46mm
22.5mm
18mm
46mm
46mm
Wiring Instructions and Diagrams
1.Turn off the power supply before carrying out any
electrical installation work.
2. Connect wires according to the wiring diagram.
3. Insert the module into the junction box.
4. Connect the power supply and follow
Curtain module
conguration instructions.
Notes: Take your smartphone close to the Curtain
sure you have min. 50% Wi-Fi signal.
Global international operation Whenever & Wherever
You are,All-in-one Mobile App
Anywhere
APP
APP
Voice control-work
with google home Voice control-work with Amazon Alexa Device Sharing
Apps
APP
Router Voice control Curtain Switch
Inhouse local operation
NL
LN
M
Scan the QR code to download Tuya Smart App, or
you can also search keyword “Tuya Smart” at App
Store or Googleplay to download App.
IOS APP / Android APP
APP USER MANUAL
INSTALLATION
Warnings:
1.
electrician in accordance with local regulations.
2. Keep the device out of reach of children.
MANUAL OVERRIDE
The Curtain module terminal reserves the access of
manual override function for the end-user to switch on/off.
· If you have connected the wall push-button, check
its work. Single pressing ofthe "down" button / "up"
button, will cause that the roller shutters moves in
the desired direction to the end position. If the ele-
ctric shutter goes in the opposite direction to the
expected,select "motor reversal" in the "More"op-
tion. When the electric shutter is moving up, press-
ing "up" button switches causes that the shutter
will stop immediately; when the electric shutter is
moving down, pressing "down" button switches
causes that the shutter will stop immediately.
Notes:
1) Both the adjustment on App and
Curtain can overwrite
each other, the last adjustment remains in memory.
2) The App control is synchronized with the
manual switch.

Wi-Fi Curtain Module
QS-WIFI-C01
Mounting Clip
INSTRUCTION MANUAL
Reset Key
EMC Standard (EMC)
EN 300 328 V2.1.1 (2016-11),
EN 301489-1 V2.1.1 (2017-02),
EN 301489-17 V3.1.1 (2017-02),
EN 62311: 2008, EN 61000-6-1:2007,
EN 61000-6-3:2007+A1:2011
Safety Standard (LVD)
IEC 60669-2-1:2002/AMD1:2008/
AMD2:2015, IEC 60669-1:1998/
AMD1:1999/AMD2:2006,
EN 60669-2-1:2004+A1: 2009+ A2:2010,
EN 60669-1:2018
RoHS Standard (RoHS)
2011/65/EU, (EU) 2015/863
Radio Equipment (RED)
ETSI EN 300 328 V2.1.1 (2016-11)
TECHNICAL SPECIFICATIONS
Product type Wi-Fi Curtain Module
Voltage 220-240V AC 50/60Hz
Current 3A
WiFi frequency 2.4GHz - 2.4835GHz WIFI
Operation temp. -10C - +40C
Case temp. Tc: +80C (Max.)
Operation range ≤ 200 m
Dims (WxDxH) 46x46x18mm(without clip)
IP rating IP20
Warranty 3 years
3. Keep the device away from water , damp or hot
environment.
4. Install the device away from strong signal sources
such as mic rowave oven that may cause signal
interruption resulted to abnormal operation of the
device.
5. Obstruction by concrete wall or metallic
materials may reduce the effective operation
range of the device and should be avoided.
6. Do NOT attempt to disassemble,repair or modify
the device.
FAQ
Q1: What should I do if I can’t congure the Curtain
module?
a. Please check whether device is powered on.
b. Make sure your mobile and Curtain module
are under the same 2.4 Ghz WIFI network.
c. Whether it’s in good internet conditions.
d. Make sure the password entered in App is correct.
e. Make sure the wiring is correct.
Q2: Which products can I control with the device?
Q3: What happens if the WIFI goes off?
Curtain,shutter, blind.....
You can still control the device connected the Curtain
module with your traditional Curtain and once WIFI is
active again the device connected to module will
connect automatically to your WIFI network.
Q4: What should I do if I change the WIFI network or
change the password?
You can connect the module to the WIFI network
according to the App User Manual.
Q 5: How do I reset the device?
Power on/off device 5 times or press the reset key for
about 10 seconds until the beeper on the module sound
continuously.
with mounting clip without mounting clip
50mm
46mm
22.5mm
18mm
46mm
46mm
Wiring Instructions and Diagrams
1.Turn off the power supply before carrying out any
electrical installation work.
2. Connect wires according to the wiring diagram.
3. Insert the module into the junction box.
4. Connect the power supply and follow
Curtain module
conguration instructions.
Notes: Take your smartphone close to the Curtain
sure you have min. 50% Wi-Fi signal.
Global international operation Whenever & Wherever
You are,All-in-one Mobile App
Anywhere
APP
APP
Voice control-work
with google home Voice control-work with Amazon Alexa Device Sharing
Apps
APP
Router Voice control Curtain Switch
Inhouse local operation
NL
LN
M
Scan the QR code to download Tuya Smart App, or
you can also search keyword “Tuya Smart” at App
Store or Googleplay to download App.
IOS APP / Android APP
APP USER MANUAL
INSTALLATION
Warnings:
1.
electrician in accordance with local regulations.
2. Keep the device out of reach of children.
MANUAL OVERRIDE
The Curtain module terminal reserves the access of
manual override function for the end-user to switch on/off.
· If you have connected the wall push-button, check
its work. Single pressing ofthe "down" button / "up"
button, will cause that the roller shutters moves in
the desired direction to the end position. If the ele-
ctric shutter goes in the opposite direction to the
expected,select "motor reversal" in the "More"op-
tion. When the electric shutter is moving up, press-
ing "up" button switches causes that the shutter
will stop immediately; when the electric shutter is
moving down, pressing "down" button switches
causes that the shutter will stop immediately.
Notes:
1) Both the adjustment on App and
Curtain can overwrite
each other, the last adjustment remains in memory.
2) The App control is synchronized with the
manual switch.

Wi-Fi Curtain Module
QS-WIFI-C01
Mounting Clip
INSTRUCTION MANUAL
Reset Key
EMC Standard (EMC)
EN 300 328 V2.1.1 (2016-11),
EN 301489-1 V2.1.1 (2017-02),
EN 301489-17 V3.1.1 (2017-02),
EN 62311: 2008, EN 61000-6-1:2007,
EN 61000-6-3:2007+A1:2011
Safety Standard (LVD)
IEC 60669-2-1:2002/AMD1:2008/
AMD2:2015, IEC 60669-1:1998/
AMD1:1999/AMD2:2006,
EN 60669-2-1:2004+A1: 2009+ A2:2010,
EN 60669-1:2018
RoHS Standard (RoHS)
2011/65/EU, (EU) 2015/863
Radio Equipment (RED)
ETSI EN 300 328 V2.1.1 (2016-11)
TECHNICAL SPECIFICATIONS
Product type Wi-Fi Curtain Module
Voltage 220-240V AC 50/60Hz
Current 3A
WiFi frequency 2.4GHz - 2.4835GHz WIFI
Operation temp. -10C - +40C
Case temp. Tc: +80C (Max.)
Operation range ≤ 200 m
Dims (WxDxH) 46x46x18mm(without clip)
IP rating IP20
Warranty 3 years
3. Keep the device away from water , damp or hot
environment.
4. Install the device away from strong signal sources
such as mic rowave oven that may cause signal
interruption resulted to abnormal operation of the
device.
5. Obstruction by concrete wall or metallic
materials may reduce the effective operation
range of the device and should be avoided.
6. Do NOT attempt to disassemble,repair or modify
the device.
FAQ
Q1: What should I do if I can’t congure the Curtain
module?
a. Please check whether device is powered on.
b. Make sure your mobile and Curtain module
are under the same 2.4 Ghz WIFI network.
c. Whether it’s in good internet conditions.
d. Make sure the password entered in App is correct.
e. Make sure the wiring is correct.
Q2: Which products can I control with the device?
Q3: What happens if the WIFI goes off?
Curtain,shutter, blind.....
You can still control the device connected the Curtain
module with your traditional Curtain and once WIFI is
active again the device connected to module will
connect automatically to your WIFI network.
Q4: What should I do if I change the WIFI network or
change the password?
You can connect the module to the WIFI network
according to the App User Manual.
Q 5: How do I reset the device?
Power on/off device 5 times or press the reset key for
about 10 seconds until the beeper on the module sound
continuously.
with mounting clip without mounting clip
50mm
46mm
22.5mm
18mm
46mm
46mm
Wiring Instructions and Diagrams
1.Turn off the power supply before carrying out any
electrical installation work.
2. Connect wires according to the wiring diagram.
3. Insert the module into the junction box.
4. Connect the power supply and follow
Curtain module
conguration instructions.
Notes: Take your smartphone close to the Curtain
sure you have min. 50% Wi-Fi signal.
Global international operation Whenever & Wherever
You are,All-in-one Mobile App
Anywhere
APP
APP
Voice control-work
with google home Voice control-work with Amazon Alexa Device Sharing
Apps
APP
Router Voice control Curtain Switch
Inhouse local operation
NL
LN
M
Scan the QR code to download Tuya Smart App, or
you can also search keyword “Tuya Smart” at App
Store or Googleplay to download App.
IOS APP / Android APP
APP USER MANUAL
INSTALLATION
Warnings:
1.
electrician in accordance with local regulations.
2. Keep the device out of reach of children.
MANUAL OVERRIDE
The Curtain module terminal reserves the access of
manual override function for the end-user to switch on/off.
· If you have connected the wall push-button, check
its work. Single pressing ofthe "down" button / "up"
button, will cause that the roller shutters moves in
the desired direction to the end position. If the ele-
ctric shutter goes in the opposite direction to the
expected,select "motor reversal" in the "More"op-
tion. When the electric shutter is moving up, press-
ing "up" button switches causes that the shutter
will stop immediately; when the electric shutter is
moving down, pressing "down" button switches
causes that the shutter will stop immediately.
Notes:
1) Both the adjustment on App and
Curtain can overwrite
each other, the last adjustment remains in memory.
2) The App control is synchronized with the
manual switch.

Wi-Fi Curtain Module
QS-WIFI-C01
Mounting Clip
INSTRUCTION MANUAL
Reset Key
EMC Standard (EMC)
EN 300 328 V2.1.1 (2016-11),
EN 301489-1 V2.1.1 (2017-02),
EN 301489-17 V3.1.1 (2017-02),
EN 62311: 2008, EN 61000-6-1:2007,
EN 61000-6-3:2007+A1:2011
Safety Standard (LVD)
IEC 60669-2-1:2002/AMD1:2008/
AMD2:2015, IEC 60669-1:1998/
AMD1:1999/AMD2:2006,
EN 60669-2-1:2004+A1: 2009+ A2:2010,
EN 60669-1:2018
RoHS Standard (RoHS)
2011/65/EU, (EU) 2015/863
Radio Equipment (RED)
ETSI EN 300 328 V2.1.1 (2016-11)
TECHNICAL SPECIFICATIONS
Product type Wi-Fi Curtain Module
Voltage 220-240V AC 50/60Hz
Current 3A
WiFi frequency 2.4GHz - 2.4835GHz WIFI
Operation temp. -10C - +40C
Case temp. Tc: +80C (Max.)
Operation range ≤ 200 m
Dims (WxDxH) 46x46x18mm(without clip)
IP rating IP20
Warranty 3 years
3. Keep the device away from water , damp or hot
environment.
4. Install the device away from strong signal sources
such as mic rowave oven that may cause signal
interruption resulted to abnormal operation of the
device.
5. Obstruction by concrete wall or metallic
materials may reduce the effective operation
range of the device and should be avoided.
6. Do NOT attempt to disassemble,repair or modify
the device.
FAQ
Q1: What should I do if I can’t congure the Curtain
module?
a. Please check whether device is powered on.
b. Make sure your mobile and Curtain module
are under the same 2.4 Ghz WIFI network.
c. Whether it’s in good internet conditions.
d. Make sure the password entered in App is correct.
e. Make sure the wiring is correct.
Q2: Which products can I control with the device?
Q3: What happens if the WIFI goes off?
Curtain,shutter, blind.....
You can still control the device connected the Curtain
module with your traditional Curtain and once WIFI is
active again the device connected to module will
connect automatically to your WIFI network.
Q4: What should I do if I change the WIFI network or
change the password?
You can connect the module to the WIFI network
according to the App User Manual.
Q 5: How do I reset the device?
Power on/off device 5 times or press the reset key for
about 10 seconds until the beeper on the module sound
continuously.
with mounting clip without mounting clip
50mm
46mm
22.5mm
18mm
46mm
46mm
Wiring Instructions and Diagrams
1.Turn off the power supply before carrying out any
electrical installation work.
2. Connect wires according to the wiring diagram.
3. Insert the module into the junction box.
4. Connect the power supply and follow
Curtain module
conguration instructions.
Notes: Take your smartphone close to the Curtain
sure you have min. 50% Wi-Fi signal.
Global international operation Whenever & Wherever
You are,All-in-one Mobile App
Anywhere
APP
APP
Voice control-work
with google home Voice control-work with Amazon Alexa Device Sharing
Apps
APP
Router Voice control Curtain Switch
Inhouse local operation
NL
LN
M
Scan the QR code to download Tuya Smart App, or
you can also search keyword “Tuya Smart” at App
Store or Googleplay to download App.
IOS APP / Android APP
APP USER MANUAL
INSTALLATION
Warnings:
1.
electrician in accordance with local regulations.
2. Keep the device out of reach of children.
MANUAL OVERRIDE
The Curtain module terminal reserves the access of
manual override function for the end-user to switch on/off.
· If you have connected the wall push-button, check
its work. Single pressing ofthe "down" button / "up"
button, will cause that the roller shutters moves in
the desired direction to the end position. If the ele-
ctric shutter goes in the opposite direction to the
expected,select "motor reversal" in the "More"op-
tion. When the electric shutter is moving up, press-
ing "up" button switches causes that the shutter
will stop immediately; when the electric shutter is
moving down, pressing "down" button switches
causes that the shutter will stop immediately.
Notes:
1) Both the adjustment on App and
Curtain can overwrite
each other, the last adjustment remains in memory.
2) The App control is synchronized with the
manual switch.

Wi-Fi Curtain Module
QS-WIFI-C01
Mounting Clip
INSTRUCTION MANUAL
Reset Key
EMC Standard (EMC)
EN 300 328 V2.1.1 (2016-11),
EN 301489-1 V2.1.1 (2017-02),
EN 301489-17 V3.1.1 (2017-02),
EN 62311: 2008, EN 61000-6-1:2007,
EN 61000-6-3:2007+A1:2011
Safety Standard (LVD)
IEC 60669-2-1:2002/AMD1:2008/
AMD2:2015, IEC 60669-1:1998/
AMD1:1999/AMD2:2006,
EN 60669-2-1:2004+A1: 2009+ A2:2010,
EN 60669-1:2018
RoHS Standard (RoHS)
2011/65/EU, (EU) 2015/863
Radio Equipment (RED)
ETSI EN 300 328 V2.1.1 (2016-11)
TECHNICAL SPECIFICATIONS
Product type Wi-Fi Curtain Module
Voltage 220-240V AC 50/60Hz
Current 3A
WiFi frequency 2.4GHz - 2.4835GHz WIFI
Operation temp. -10C - +40C
Case temp. Tc: +80C (Max.)
Operation range ≤ 200 m
Dims (WxDxH) 46x46x18mm(without clip)
IP rating IP20
Warranty 3 years
3. Keep the device away from water , damp or hot
environment.
4. Install the device away from strong signal sources
such as mic rowave oven that may cause signal
interruption resulted to abnormal operation of the
device.
5. Obstruction by concrete wall or metallic
materials may reduce the effective operation
range of the device and should be avoided.
6. Do NOT attempt to disassemble,repair or modify
the device.
FAQ
Q1: What should I do if I can’t congure the Curtain
module?
a. Please check whether device is powered on.
b. Make sure your mobile and Curtain module
are under the same 2.4 Ghz WIFI network.
c. Whether it’s in good internet conditions.
d. Make sure the password entered in App is correct.
e. Make sure the wiring is correct.
Q2: Which products can I control with the device?
Q3: What happens if the WIFI goes off?
Curtain,shutter, blind.....
You can still control the device connected the Curtain
module with your traditional Curtain and once WIFI is
active again the device connected to module will
connect automatically to your WIFI network.
Q4: What should I do if I change the WIFI network or
change the password?
You can connect the module to the WIFI network
according to the App User Manual.
Q 5: How do I reset the device?
Power on/off device 5 times or press the reset key for
about 10 seconds until the beeper on the module sound
continuously.
with mounting clip without mounting clip
50mm
46mm
22.5mm
18mm
46mm
46mm
Wiring Instructions and Diagrams
1.Turn off the power supply before carrying out any
electrical installation work.
2. Connect wires according to the wiring diagram.
3. Insert the module into the junction box.
4. Connect the power supply and follow
Curtain module
conguration instructions.
Notes: Take your smartphone close to the Curtain
sure you have min. 50% Wi-Fi signal.
Global international operation Whenever & Wherever
You are,All-in-one Mobile App
Anywhere
APP
APP
Voice control-work
with google home Voice control-work with Amazon Alexa Device Sharing
Apps
APP
Router Voice control Curtain Switch
Inhouse local operation
NL
LN
M
Scan the QR code to download Tuya Smart App, or
you can also search keyword “Tuya Smart” at App
Store or Googleplay to download App.
IOS APP / Android APP
APP USER MANUAL
INSTALLATION
Warnings:
1.
electrician in accordance with local regulations.
2. Keep the device out of reach of children.
MANUAL OVERRIDE
The Curtain module terminal reserves the access of
manual override function for the end-user to switch on/off.
· If you have connected the wall push-button, check
its work. Single pressing ofthe "down" button / "up"
button, will cause that the roller shutters moves in
the desired direction to the end position. If the ele-
ctric shutter goes in the opposite direction to the
expected,select "motor reversal" in the "More"op-
tion. When the electric shutter is moving up, press-
ing "up" button switches causes that the shutter
will stop immediately; when the electric shutter is
moving down, pressing "down" button switches
causes that the shutter will stop immediately.
Notes:
1) Both the adjustment on App and
Curtain can overwrite
each other, the last adjustment remains in memory.
2) The App control is synchronized with the
manual switch.

Connect to amazon alexa or Google Assistant
for voice control, or share the devices with your
families or friends.
More
Device name
Basic information about the device
Supported Third-party
Control Others
Others
Shared devices
Create Group
Device information
Feedback
Device Location
Check network
amazon
alexa Google Assistant
Log in or register your account with your mobile
code sent to your mobile or mail box, then set your
login password. Click "Create Family" to enter into
the APP.
Mobile number/e-mail add ress
Region
Obtain verification code
Make sure your smart phone and Wi-Fi curtain
module are under the same Wi-Fi network at
sound continuously for pairing mode.
Add Device
Add Device
Confirm indicator rapidly blink
After the wiring of curtain module is done, press
the traditional switch to turn ON/OFF cycle for 5
times (keep time interval not too short) or press
the reset key for about 10s until the beep sound
continuously for pairing mode.
The pairing will take about 10-120 seconds to
complete depending on your network condition.
Connecting
Device found
Register device to the smart cloud
Initializing device
Make sure your router,mobile,and
device are as close as possible
2%
Enjoy your smart life of home automation for
lighting control by using our All-in-one mobile
app wherever you are in the world or simply by
voice control when you are sitting at home
comfortably.
Voice control
App control
APP
Open the APP, selecting "+" on top right to add
device. Choose "Electrical", and select "Curtain
Switch".
Electrical
Add manually Auto Scan
Cancel
Large
Home App..
Socket(Wi-Fi) Switch(Wi-Fi)
Power(Wi-Fi)
Small
Home App..
Kitchen
Appliance
Security
& Sensur
Add Device
Lighting
When pairing is done, the Wi-Fi curtain will be
shown on the App.
Curtain Switch
Add Device
Done
Bedtoom Main bedroom
Electrical
Engineeri..
Curtain Switch
(Wi-Fi)
Power on the device and confirm
than indicator light rapidly blinks
Resetting Devices
Device addedsuccessfully
Restaurant
Secon...droom
Kitchen Light

Connect to amazon alexa or Google Assistant
for voice control, or share the devices with your
families or friends.
More
Device name
Basic information about the device
Supported Third-party
Control Others
Others
Shared devices
Create Group
Device information
Feedback
Device Location
Check network
amazon
alexa Google Assistant
Log in or register your account with your mobile
code sent to your mobile or mail box, then set your
login password. Click "Create Family" to enter into
the APP.
Mobile number/e-mail add ress
Region
Obtain verification code
Make sure your smart phone and Wi-Fi curtain
module are under the same Wi-Fi network at
sound continuously for pairing mode.
Add Device
Add Device
Confirm indicator rapidly blink
After the wiring of curtain module is done, press
the traditional switch to turn ON/OFF cycle for 5
times (keep time interval not too short) or press
the reset key for about 10s until the beep sound
continuously for pairing mode.
The pairing will take about 10-120 seconds to
complete depending on your network condition.
Connecting
Device found
Register device to the smart cloud
Initializing device
Make sure your router,mobile,and
device are as close as possible
2%
Enjoy your smart life of home automation for
lighting control by using our All-in-one mobile
app wherever you are in the world or simply by
voice control when you are sitting at home
comfortably.
Voice control
App control
APP
Open the APP, selecting "+" on top right to add
device. Choose "Electrical", and select "Curtain
Switch".
Electrical
Add manually Auto Scan
Cancel
Large
Home App..
Socket(Wi-Fi) Switch(Wi-Fi)
Power(Wi-Fi)
Small
Home App..
Kitchen
Appliance
Security
& Sensur
Add Device
Lighting
When pairing is done, the Wi-Fi curtain will be
shown on the App.
Curtain Switch
Add Device
Done
Bedtoom Main bedroom
Electrical
Engineeri..
Curtain Switch
(Wi-Fi)
Power on the device and confirm
than indicator light rapidly blinks
Resetting Devices
Device addedsuccessfully
Restaurant
Secon...droom
Kitchen Light

Connect to amazon alexa or Google Assistant
for voice control, or share the devices with your
families or friends.
More
Device name
Basic information about the device
Supported Third-party
Control Others
Others
Shared devices
Create Group
Device information
Feedback
Device Location
Check network
amazon
alexa Google Assistant
Log in or register your account with your mobile
code sent to your mobile or mail box, then set your
login password. Click "Create Family" to enter into
the APP.
Mobile number/e-mail add ress
Region
Obtain verification code
Make sure your smart phone and Wi-Fi curtain
module are under the same Wi-Fi network at
sound continuously for pairing mode.
Add Device
Add Device
Confirm indicator rapidly blink
After the wiring of curtain module is done, press
the traditional switch to turn ON/OFF cycle for 5
times (keep time interval not too short) or press
the reset key for about 10s until the beep sound
continuously for pairing mode.
The pairing will take about 10-120 seconds to
complete depending on your network condition.
Connecting
Device found
Register device to the smart cloud
Initializing device
Make sure your router,mobile,and
device are as close as possible
2%
Enjoy your smart life of home automation for
lighting control by using our All-in-one mobile
app wherever you are in the world or simply by
voice control when you are sitting at home
comfortably.
Voice control
App control
APP
Open the APP, selecting "+" on top right to add
device. Choose "Electrical", and select "Curtain
Switch".
Electrical
Add manually Auto Scan
Cancel
Large
Home App..
Socket(Wi-Fi) Switch(Wi-Fi)
Power(Wi-Fi)
Small
Home App..
Kitchen
Appliance
Security
& Sensur
Add Device
Lighting
When pairing is done, the Wi-Fi curtain will be
shown on the App.
Curtain Switch
Add Device
Done
Bedtoom Main bedroom
Electrical
Engineeri..
Curtain Switch
(Wi-Fi)
Power on the device and confirm
than indicator light rapidly blinks
Resetting Devices
Device addedsuccessfully
Restaurant
Secon...droom
Kitchen Light

Connect to amazon alexa or Google Assistant
for voice control, or share the devices with your
families or friends.
More
Device name
Basic information about the device
Supported Third-party
Control Others
Others
Shared devices
Create Group
Device information
Feedback
Device Location
Check network
amazon
alexa Google Assistant
Log in or register your account with your mobile
code sent to your mobile or mail box, then set your
login password. Click "Create Family" to enter into
the APP.
Mobile number/e-mail add ress
Region
Obtain verification code
Make sure your smart phone and Wi-Fi curtain
module are under the same Wi-Fi network at
sound continuously for pairing mode.
Add Device
Add Device
Confirm indicator rapidly blink
After the wiring of curtain module is done, press
the traditional switch to turn ON/OFF cycle for 5
times (keep time interval not too short) or press
the reset key for about 10s until the beep sound
continuously for pairing mode.
The pairing will take about 10-120 seconds to
complete depending on your network condition.
Connecting
Device found
Register device to the smart cloud
Initializing device
Make sure your router,mobile,and
device are as close as possible
2%
Enjoy your smart life of home automation for
lighting control by using our All-in-one mobile
app wherever you are in the world or simply by
voice control when you are sitting at home
comfortably.
Voice control
App control
APP
Open the APP, selecting "+" on top right to add
device. Choose "Electrical", and select "Curtain
Switch".
Electrical
Add manually Auto Scan
Cancel
Large
Home App..
Socket(Wi-Fi) Switch(Wi-Fi)
Power(Wi-Fi)
Small
Home App..
Kitchen
Appliance
Security
& Sensur
Add Device
Lighting
When pairing is done, the Wi-Fi curtain will be
shown on the App.
Curtain Switch
Add Device
Done
Bedtoom Main bedroom
Electrical
Engineeri..
Curtain Switch
(Wi-Fi)
Power on the device and confirm
than indicator light rapidly blinks
Resetting Devices
Device addedsuccessfully
Restaurant
Secon...droom
Kitchen Light

Connect to amazon alexa or Google Assistant
for voice control, or share the devices with your
families or friends.
More
Device name
Basic information about the device
Supported Third-party
Control Others
Others
Shared devices
Create Group
Device information
Feedback
Device Location
Check network
amazon
alexa Google Assistant
Log in or register your account with your mobile
code sent to your mobile or mail box, then set your
login password. Click "Create Family" to enter into
the APP.
Mobile number/e-mail add ress
Region
Obtain verification code
Make sure your smart phone and Wi-Fi curtain
module are under the same Wi-Fi network at
sound continuously for pairing mode.
Add Device
Add Device
Confirm indicator rapidly blink
After the wiring of curtain module is done, press
the traditional switch to turn ON/OFF cycle for 5
times (keep time interval not too short) or press
the reset key for about 10s until the beep sound
continuously for pairing mode.
The pairing will take about 10-120 seconds to
complete depending on your network condition.
Connecting
Device found
Register device to the smart cloud
Initializing device
Make sure your router,mobile,and
device are as close as possible
2%
Enjoy your smart life of home automation for
lighting control by using our All-in-one mobile
app wherever you are in the world or simply by
voice control when you are sitting at home
comfortably.
Voice control
App control
APP
Open the APP, selecting "+" on top right to add
device. Choose "Electrical", and select "Curtain
Switch".
Electrical
Add manually Auto Scan
Cancel
Large
Home App..
Socket(Wi-Fi) Switch(Wi-Fi)
Power(Wi-Fi)
Small
Home App..
Kitchen
Appliance
Security
& Sensur
Add Device
Lighting
When pairing is done, the Wi-Fi curtain will be
shown on the App.
Curtain Switch
Add Device
Done
Bedtoom Main bedroom
Electrical
Engineeri..
Curtain Switch
(Wi-Fi)
Power on the device and confirm
than indicator light rapidly blinks
Resetting Devices
Device addedsuccessfully
Restaurant
Secon...droom
Kitchen Light

Connect to amazon alexa or Google Assistant
for voice control, or share the devices with your
families or friends.
More
Device name
Basic information about the device
Supported Third-party
Control Others
Others
Shared devices
Create Group
Device information
Feedback
Device Location
Check network
amazon
alexa Google Assistant
Log in or register your account with your mobile
code sent to your mobile or mail box, then set your
login password. Click "Create Family" to enter into
the APP.
Mobile number/e-mail add ress
Region
Obtain verification code
Make sure your smart phone and Wi-Fi curtain
module are under the same Wi-Fi network at
sound continuously for pairing mode.
Add Device
Add Device
Confirm indicator rapidly blink
After the wiring of curtain module is done, press
the traditional switch to turn ON/OFF cycle for 5
times (keep time interval not too short) or press
the reset key for about 10s until the beep sound
continuously for pairing mode.
The pairing will take about 10-120 seconds to
complete depending on your network condition.
Connecting
Device found
Register device to the smart cloud
Initializing device
Make sure your router,mobile,and
device are as close as possible
2%
Enjoy your smart life of home automation for
lighting control by using our All-in-one mobile
app wherever you are in the world or simply by
voice control when you are sitting at home
comfortably.
Voice control
App control
APP
Open the APP, selecting "+" on top right to add
device. Choose "Electrical", and select "Curtain
Switch".
Electrical
Add manually Auto Scan
Cancel
Large
Home App..
Socket(Wi-Fi) Switch(Wi-Fi)
Power(Wi-Fi)
Small
Home App..
Kitchen
Appliance
Security
& Sensur
Add Device
Lighting
When pairing is done, the Wi-Fi curtain will be
shown on the App.
Curtain Switch
Add Device
Done
Bedtoom Main bedroom
Electrical
Engineeri..
Curtain Switch
(Wi-Fi)
Power on the device and confirm
than indicator light rapidly blinks
Resetting Devices
Device addedsuccessfully
Restaurant
Secon...droom
Kitchen Light

Connect to amazon alexa or Google Assistant
for voice control, or share the devices with your
families or friends.
More
Device name
Basic information about the device
Supported Third-party
Control Others
Others
Shared devices
Create Group
Device information
Feedback
Device Location
Check network
amazon
alexa Google Assistant
Log in or register your account with your mobile
code sent to your mobile or mail box, then set your
login password. Click "Create Family" to enter into
the APP.
Mobile number/e-mail add ress
Region
Obtain verification code
Make sure your smart phone and Wi-Fi curtain
module are under the same Wi-Fi network at
sound continuously for pairing mode.
Add Device
Add Device
Confirm indicator rapidly blink
After the wiring of curtain module is done, press
the traditional switch to turn ON/OFF cycle for 5
times (keep time interval not too short) or press
the reset key for about 10s until the beep sound
continuously for pairing mode.
The pairing will take about 10-120 seconds to
complete depending on your network condition.
Connecting
Device found
Register device to the smart cloud
Initializing device
Make sure your router,mobile,and
device are as close as possible
2%
Enjoy your smart life of home automation for
lighting control by using our All-in-one mobile
app wherever you are in the world or simply by
voice control when you are sitting at home
comfortably.
Voice control
App control
APP
Open the APP, selecting "+" on top right to add
device. Choose "Electrical", and select "Curtain
Switch".
Electrical
Add manually Auto Scan
Cancel
Large
Home App..
Socket(Wi-Fi) Switch(Wi-Fi)
Power(Wi-Fi)
Small
Home App..
Kitchen
Appliance
Security
& Sensur
Add Device
Lighting
When pairing is done, the Wi-Fi curtain will be
shown on the App.
Curtain Switch
Add Device
Done
Bedtoom Main bedroom
Electrical
Engineeri..
Curtain Switch
(Wi-Fi)
Power on the device and confirm
than indicator light rapidly blinks
Resetting Devices
Device addedsuccessfully
Restaurant
Secon...droom
Kitchen Light

Connect to amazon alexa or Google Assistant
for voice control, or share the devices with your
families or friends.
More
Device name
Basic information about the device
Supported Third-party
Control Others
Others
Shared devices
Create Group
Device information
Feedback
Device Location
Check network
amazon
alexa Google Assistant
Log in or register your account with your mobile
code sent to your mobile or mail box, then set your
login password. Click "Create Family" to enter into
the APP.
Mobile number/e-mail add ress
Region
Obtain verification code
Make sure your smart phone and Wi-Fi curtain
module are under the same Wi-Fi network at
sound continuously for pairing mode.
Add Device
Add Device
Confirm indicator rapidly blink
After the wiring of curtain module is done, press
the traditional switch to turn ON/OFF cycle for 5
times (keep time interval not too short) or press
the reset key for about 10s until the beep sound
continuously for pairing mode.
The pairing will take about 10-120 seconds to
complete depending on your network condition.
Connecting
Device found
Register device to the smart cloud
Initializing device
Make sure your router,mobile,and
device are as close as possible
2%
Enjoy your smart life of home automation for
lighting control by using our All-in-one mobile
app wherever you are in the world or simply by
voice control when you are sitting at home
comfortably.
Voice control
App control
APP
Open the APP, selecting "+" on top right to add
device. Choose "Electrical", and select "Curtain
Switch".
Electrical
Add manually Auto Scan
Cancel
Large
Home App..
Socket(Wi-Fi) Switch(Wi-Fi)
Power(Wi-Fi)
Small
Home App..
Kitchen
Appliance
Security
& Sensur
Add Device
Lighting
When pairing is done, the Wi-Fi curtain will be
shown on the App.
Curtain Switch
Add Device
Done
Bedtoom Main bedroom
Electrical
Engineeri..
Curtain Switch
(Wi-Fi)
Power on the device and confirm
than indicator light rapidly blinks
Resetting Devices
Device addedsuccessfully
Restaurant
Secon...droom
Kitchen Light