TV Logic LVM-071W User manual

Multi Format
LCD MONITOR
Operation Manual
LVM-071W
7” Multi Format LCD Monitor
MULTI

Contents
CAUTION 2
FEATURES 3
NAME & FUNCTION OF EACH PART 4
MENUCONTENTS 7
OTHERFUNCTIONS 13
DVI ANALOG INPUT SIGNAL FORMAT 17
DVI DIGITAL INPUT SIGNAL FORMAT 18
PRODUCTSPECIFICATION 19
PRODUCTLINEUP 20
OPTIONALACCESSORIES 23
........................................................................................
......................................................................................
.......................................................
.............................................................................
...........................................................................
.....................................................
......................................................
..................................................................
.............................................................................
...................................................................
FCC (Federal Communications Commission)
This equipment has been tested and found to comply with the limits for class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interface when the equipment is
operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential to correct the interference at his own expense
CAUTION: Change or modications not expressly approved by the manufacturer responsible for compliance void the
user’s authority to operate the equipment.
Disposal of Old Electrical & Electronic Equipment
(Applicable in the European Union and other European countries with separate collection systems)
This symbol on the product or on its packing indicates that this product shall not be treated as household waste. Instead
it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By
ensuring this product is disposed of correctly, you will help prevent potential negative consequence for the environment
and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of
materials will help to conserve natural resources.

LVM-071W
7” Multi Format LCD Monitor
02
Caution
ALWAYS USE SET VOLTAGE. DC 12V
If liquid is spilled on or impacts this product, please disconnect the product immediately and seek
professional help before continued use.
Keep unit disconnected during extended periods of disuse.
Keep unit in a well-ventilated place to prevent overheating.
Do not install the product near any heat-generating equipment.
Also, keep the product out of direct sunlight or dusty areas.
Only clean the product with a noncommercial, mild and neutral detergent.
When transporting the product, make use of its original packaging for safer carriage.

LVM-071W
Features
LVM-071W HAS THE FOLLOWING FEATURES:
Compatible with varied SDI signals
- The product is compatible with varied SDI Signals - 480i,576i,720p,1035i,1080i,1080p,1080psf
Compatible with varied analog signals
- The product is compatible with varied analog signals - Composite, S-Video, Component, RGB
Compatible with varied DVI Digital/Analog Signals
- DVI input is standard equipment
Compatible with VGA Signals using DVI-I connection
Waveform/Vector Scope/Audio Level Meter
- Waveform & Vector Scope available for SDI Signals
- Embedded Audio Level Meter
Audio in & out
- Built in Audio Disembedder and Internal Speakers
- Stereo Audio out using phone jack
- External Audio in for Mono Speaker out
Knob Control
- Easy to adjust user conguration using the control knobs.
BLUE ONLY/MONO
H/V delay
Wide Variety of Markers & Safety Areas
- Center Marker, Safety Area Marker, Aspect Marker, Display Size(Scan)
Pixel To Pixel
- Provides both full screen and unscaled native image.
Wide Screen/LED Backlight
24Bit RGB Interface Panel
DC Compatible
- The product is powered by normal 12V source.
Remote control function
- Simple remote controllability with single cable connection, no additional modules required
Additional Features
- Active Loop Through/SDI, VESA Mounting Standard, 300:1 contrast ratio, 350 cd/m2 brightness, OSD user
interface, Rack Mountable
7” Multi Format LCD Monitor
03

LVM-071W
7” Multi Format LCD Monitor
04
Name & Function of Each Part
ANALOG
DVI
SDI
BLUE ONLY/ MONO
UNDERSCAN
ASPECT
MARKER/HVDELAY
POWER
ENTER
UP
DOWN
MENU
WAVEFORM/VECTOR SCOPE
PHASE
APERTURE
BRIGHT
CHROMA
CONTRAST
VOLUME
TALLY
FRONT
[ANALOG] button/lamp
- Used to select desired Analog Input. (CVB1/2/3, S-Video, Component, RGB)
[DVI] button/lamp
- Used to select desired DVI Input. (DVI DIGITAL, DVI ANALOG)
[SDI] button/lamp
- Used to select SDI Input.
[UNDERSCAN] button/lamp
- Used to transfer from OVER SCAN mode to UNDER SCAN mode.
- Mode changes in the order of UNDERSCAN -> OVERSCAN -> PIXEL TO PIXEL -> UNDERSCAN.
#PIXEL TO PIXEL mode is not available in Graphic mode.
[ASPECT] button/lamp
- Used to toggle aspect ratio in SD from standard to anamorphic.
[MARKER]/[HVDELAY] button/lamp
- Used to show MARKER on the screen. The type of marker at work may be selected on the main menu.
Press and Hold the button to activate the HV Delay mode.

7” Multi Format LCD Monitor
05
LVM-071W
Name & Function of Each Part
[BLUE ONLY]/[MONO] button/lamp
- You may remove R(red) and G(green) from the input signal and play the screen only with B(blue) signal.
Button may be pressed twice to change the screen to MONO mode.
(This mode uses only Luminance value.)
[PHASE] button/lamp
- Used to change the Phase values.
#Phase is not available in DVI Analog and PAL mode.
[WAVEFORM]/[VECTOR SCOPE] button/lamp
- Used to activate the Waveform or Vector Scope. Pressing the button once will activate the Waveform,
pressing the button twice activates the Vector Scope.
[MENU] button
- Used to activate the OSD menu.
[UP] button
- Used to navigate menu during OSD menu activation. It may also be used to toggle clockwise through
1:1 quadrants in native scan mode.
[DOWN] button
- Used to navigate menu during OSD menu activation. It may also be used to toggle counterclockwise
through 1:1 quadrants in native scan mode.
[ENTER] button
- Used to conrm a chosen value (or mode) within the OSD menu.
[POWER] switch
- Power On/O button. If the signal is normal, LED lights in Green. If the signal is unsupported or
disconnected, LED ashes in Yellow.
[TALLY] lamp
- LED indicating monitor’s current status using optional Remote/RS-485.
[APERTURE] knob
- Used to adjust the picture sharpness between MAX(12) and MIN(-12).
#Aperture is not available in DVI Analog mode.
[BRIGHT] knob
- Used to adjust the degree of brightness between MAX(25) and MIN(-25).
[CHROMA] knob
- Used to adjust the saturation between MAX(25) and MIN(-25).
#Chroma is not available in DVI Analog mode.
[CONTRAST] knob
- Used to adjust the contrast ration between MAX(25) and MIN(-25).
[VOLUME] knob
- Used to adjust the volume between MAX(20) and MIN(0).

LVM-071W
7” Multi Format LCD Monitor
06
Name & Function of Each Part
DVI DIGITAL/
DVI ANALOG
SDI-IN
SDI-OUT
CVBS1/B/Pb
CVBS2/G/Y/S-Y
CVBS3/R/Pr/S-C
AUDIO IN
AUDIO OUT
REMOTE
FACTORY PGM
DC IN
REAR
REMOTE (RJ-45)
- Connection for remote control of monitor.
DVI DIGITAL/DVI ANALOG (DVI-I)
- Input connection for DVI-I.
SDI-IN (BNC)
- SDI signal input terminal.
SDI-OUT (BNC)
- SDI signal output terminal.
CVBS1/B/Pb (BNC)
- Signal input terminal used for COMPOSITE1, RGB B, COMPONENT Pb signals.
CVBS2/G/Y/S-Y (BNC)
- Signal input terminal used for COMPOSITE2, RGB G, COMPONENT Y, SVIDEO signals.
CVBS3/R/Pr/S-C (BNC)
- Signal input terminal used for COMPOSITE3, RGB R, COMPONENT Pr, SVIDEO C signals.
AUDIO IN (Phone jack)
- Used to External audio input jack.
AUDIO OUT (phone jack)
- Used to audio output jack.
FACTORY PGM (40 pins)
- Input connector for FACTORY PGM allowing for rmware updates.
DC IN (XLR, 4 pins)
- Used to supply DC power; 12V.

7” Multi Format LCD Monitor
07
LVM-071W
Menu Contents
[1] PICTURE PART
Below is the description of each function of the menu.
Brightness
This Item controls the degree of brightness.
#Brightness can be adjusted by using the [BRIGHT] control knob on the front of the monitor.
CONTRAST
This item controls the contrast ratio.
#Contrast can be adjusted by using the [CONTRAST] control knob on the front of the monitor.
CHROMA
This item controls saturation.
#Saturation can be adjusted by using the [CHROMA] control knob on the front of the monitor.
PHASE
This item controls Phase value (Hue).
#Phase value can be adjusted by press the [PHASE] button on the front of the monitor.
APERTURE
This item controls the picture sharpness.
#Sharpness can be adjusted by using the [APERTURE] control knob on the front of the monitor.
NTSC Setup
This item sets IRE value in NTSC mode between 0 IRE and 7.5 IRE.

LVM-071W
7” Multi Format LCD Monitor
08
Menu Contents
[2] PICTURE PART - DVI ANALOG ONLY
Brightness
This Item controls the degree of brightness.
#Brightness can be adjusted by using the [BRIGHT] control knob on the front of the monitor.
CONTRAST
This item controls the contrast ratio.
#Contrast can be adjusted by using the [CONTRAST] control knob on the front of the monitor.
Image Position
This item controls the position(H/V) of the image in DVI Analog mode.
PHASE
This item controls Phase value.
Clocks/Line
This item is adjust timing for signal sync
Auto Adjustment
This item adjusts the input signal automatically. Phase, Clocks/Line and Image Position are also
adjusted.