TV Logic LVM-172W User manual

Multi Format
LCD MONITOR
O
peration Manua
l
MULTI
LVM-1
72
W
LVM-
242
W

Contents
CAUTION 4
FEATURES 6
NAME&FUNCTIONOFEACHPART 7
MENU ORGANIZATION & ADJUSTMENT 13
MENU CONTENTS 14
OTHERFUNCTIONS 24
DVIDIGITAL/ANALOGINPUTSIGNALFORMAT 28
PRODUCTSPECIFICATION 30
PRODUCTLINEUP 32
OPTIONALACCESSORIES 34
FCC (Federal Communications Commission
)
T
his equipment has been tested and
f
ound to comply with the limits
f
or class A digital device, pursuant to part 15 o
f
the
F
CC Rules. These limits are desi
g
ned to provide reasonable protection a
g
ainst harm
f
ul inter
f
ace when the equipment is
op
erated in a commercial environment.
T
his equipment generates, uses, and can radiate radio
f
requenc
y
energ
y
, and i
f
not installed and used in accordance with
t
he instruction manual, ma
y
cause harmful interference to radio communications. Operation of this equipment in a
residential to correct the interference at his own expens
e
CAUTION: Change or modications not expressly approved by the manufacturer responsible for compliance void the
u
ser’s aut
h
ority to operate t
h
e equipment
.
Disposal o
f
Old Electrical & Electronic Equipment
(Applicable in the European Union and other European countries with separate collection s
y
stems)
T
his s
y
mbol on the product or on its packing indicates that this product shall not be treated as household waste. Instead
i
t shall be handed over to the applicable collection point for the rec
y
cling of electrical and electronic equipment. B
y
e
nsuring this product is disposed of correctl
y
,
y
ou will help prevent potential negative consequence for the environment
and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of
materia
l
s wi
ll
h
e
l
p to conserve natura
l
resources.

Multi Format LCD Monitor
0
4
Caution
ALWAYS USE SET VOLTAGE. AC 100 ~ 240V
(
1.2A
/
50~60HZ
)
, DC 12
/
24V
(
MAX 6A
)
A
ll operatin
g
instructions must be read and understood before the product is operated.
These safet
y
and operating instructions must be kept in safe place for future reference
.
A
ll warnings on the product and in the instructions must be observed closely.
A
ll operatin
g
instructions must be followed
.
D
o not use attachments not recommended b
y
the manufacturer. Use of inadequate attachment
s
c
an result in accidents
.
This
p
roduct must be o
p
erated on a
p
ower source s
p
eci

ed on the s
p
eci

cation label.
If
you are not sure o
f
the type o
f
power supply used in your home, consult your dealer or local
power compan
y
. For units designed to operate on batteries or another power source, refer to the
o
perat
i
n
g
i
nstruct
i
ons
.
The power cords must be routed properl
y
to prevent people
f
rom stepping on them or objects
f
rom
resting on them. Check the cords at the plugs and product
.
D
o not overload AC outlets or extension cords. Overloadin
g
can cause

re or electric shock
.
N
ever insert an object into the product through vents or openings. High voltage ows in the
pro
d
uct, an
d
inserting an o
b
ject can cause e
l
ectric s
h
oc
k
an
d
/or s
h
ort interna
l
parts.
F
or the same reason, do not s
p
ill water or li
q
uid on the
p
roduct.
D
o not attempt to service the product yoursel
f
. Removing covers can expose you to high voltage
and other dan
g
erous conditions. Request a quali

ed service person to per
f
orm servicin
g
.
I
f an
y
of the following conditions occurs, unplug the power cord from the AC outlet, and request a
q
ualied service
p
erson to
p
erform re
p
airs.
a. When the power cord or plug in damaged
.
b. When a liquid was spilled on the product or when ob
j
ects have
f
allen into the product
.
c. W
h
en t
h
e pro
d
uct
h
as
b
een expose
d
to rain or water.
d
. W
h
en t
h
e pro
d
uct
d
oes not operate proper
ly
as
d
escri
b
e
d
in t
h
e operating instructions.
Do not touc
h
t
h
e contro
l
s ot
h
er t
h
an t
h
ose
d
escri
b
e
d
in t
h
e operating instructions
.
Improper adjustment of controls not described in the instructions can cause damage
,
which o
f
ten requires extensive adjustment work by a quali

ed technician.
e. When the product has been dropped or damaged
.
f
. When the product displays an abnormal condition. Any noticeable abnormality
in t
h
e pro
d
uct in
d
icates t
h
at t
h
e pro
d
uct nee
d
s servicin
g.

M
u
l
t
i F
o
rm
at
L
C
D M
o
ni
to
r
0
5
Caution
I
n case the
p
roduct needs re
p
lacement
p
arts, make sure that the service
p
erson uses
replacement parts speci

ed by the manu
f
acturer, or those with the same characteristics an
d
per
f
ormance as the ori
g
inal parts. Use o
f
unauthorized parts can result in

re, electric shock
an
d
/or ot
h
er
d
an
g
er
.
U
pon completion of service or repair work, request the service technician to perform safet
y
c
hecks to ensure that the product is in proper operating condition
.
When mountin
g
the product on a wall or ceilin
g
, be sure to install the product accordin
g
to the
method recommended by the manu
f
acturer.
U
nplu
g
the power cord from the AC outlet before cleanin
g
the product. Use a damp cloth to clean
th
e
p
ro
d
uct. Do not use
l
i
q
ui
d
c
l
eaners or aeroso
l
c
l
eaners
.
U
nplug the power cord
f
rom the AC outlet i
f
you do not use the product
f
or considerably long time
.
D
o not use t
h
e pro
d
uct near water, suc
h
as
b
at
h
tu
b
, was
hb
asin,
k
itc
h
en sin
k
an
d
l
aun
d
ry tu
b
,
s
wimmin
g
poo
l
an
d
in a wet
b
asement
.
K
eep the product awa
y
from direct ra
y
s of the Sun-light.
D
o not place the product on an unstable cart, stand, tripod or table. Placing the product on an
unstable base can cause the product to
f
all, resulting in serious personal in
j
uries as well a
s
d
amage to t
h
e pro
d
uct. Use on
l
y a cart, stan
d
, tripo
d
,
b
rac
k
et or ta
bl
e recommen
d
e
d
b
y t
he
manufacturer or sold with the product. When mountin
g
the product on a wall, be sure to follo
w
t
he manufacturer's instruction. Use onl
y
the mounting hardware recommended b
y
the
manufacturer
.
When relocating the product placed on a cart, it must be moved with the utmost care.
S
udden stops, excessive
f
orce and uneven

oor sur
f
ace can cause the product to
f
all
f
rom the cart.
The vents and other openin
g
s in the cabinet are desi
g
ned for ventilation. Do not cover or bloc
k
t
hese vents and openings since insucient ventilation can cause overheating and/or shorten th
e
l
ife of the product. Do not place the product on a bed, sofa, rug or other similar surface, since the
y
c
an block ventilation openings. This product is not designed
f
or built-in installation; do not place
t
he
p
roduct in an enclosed
p
lace such as a bookcase or rack, unless
p
ro
p
er ventilation is
p
rovided
o
r
t
h
e
m
a
n
ufactu
r
e
r'
s
in
st
r
uct
i
o
n
s
a
r
e
fo
ll
o
w
ed.
The LCD panel used in this product is made of
g
lass. Therefore, it can break when the product is
d
ropped or applied with impact. Be careful not to be injured b
y
broken glass pieces in case the
L
CD
p
anel breaks
.
K
eep the product away
f
rom heat sources such as radiators, heaters, stoves and other heat
-
g
eneratin
g
products (includin
g
ampli

ers).

Features
M
ULTI-FORMAT LVM SERIES UNIT HAS THE FOLLOWING FEATURES
:
C
ompatible with varied SDI signals
- The product is compatible with varied SDI si
g
nals (408i, 576i, 720p, 1035i, 1080i, 1080p and 1080ps
f)
C
ompatible with varied analog signals
- T
h
e pro
d
uct is compati
bl
e wit
h
varie
d
ana
l
o
g
si
g
na
l
s (Composite, S-Vi
d
eo, Component, RGB, etc.
)
DVI Digital(HDCP) / Analog input support
- DVI
d
igita
l
/ana
l
og(VGA) input is avai
l
a
bl
e wit
h
out an
y
ot
h
er accessor
y.
A
ll-in-one type system
- Slim and all-in-one t
y
pe monitor that requires no other accessories and optimized
f
or space utilization
.
Waveform/Vector Scope/Audio Level Meter support
- Wave
f
orm & Vector Sco
p
e (SDI in
p
ut)
- Em
bedded
A
ud
i
o
L
e
v
el
M
ete
r
Aud
i
o
in
&
out
-
b
ui
l
t-in interna
l
s
p
ea
k
er (Em
b
e
dd
e
d
au
d
io & Externa
l
au
d
io in)
- Stereo audio out using phone jack & external audio i
n
Kno
b
Contro
l
(
LVM-172W
)
- Easy to adjust user conguration using the control knobs.
BLUE ONLY/MONO/Focus-Assist
H/V dela
y
Wide variety of Markers & Safety Areas
- Center Marker, Safety Area Marker, Aspect Marker, Display Size(Scan
)
1
:1
SC
AN
- Provides both full screen and unscaled native image
.
Wi
d
e screen com
p
ati
bl
e
- Wide screen for 16:9 aspect ratio monitoring (LVM-172W
)
- Wide screen
f
or native 16:9 aspect ratio monitorin
g
(LVM-242W
)
A
C/DC Compatibl
e
- T
h
e pro
d
uct ma
y
b
e powere
d
by
norma
l
AC source,
b
ut a
l
so capa
bl
e wit
h
12V/24V DC.
* LVM-172W : AC, DC12V/24
V
* LVM-242W : AC, DC24V Only
R
e
m
ote
co
n
t
r
o
l
fu
n
ct
i
on
- The product can be remotely controlled using external switch or RS-422 communication.
RS422/UMD
f
eature su
pp
ort
- This product supports protocols provided by TVLogic or a TSL protocol.
Add
i
t
i
o
n
al
F
eatu
r
es
- Wide Viewing Angle, Loop Through (SDI/Analog), VESA Mounting , 1000:1 Contrast ratio (LVM-242W), 900:1
Contrast ratio (LVM-172W), 350 cd/m2 brightness (LVM-172W), 400 cd/m2 brightness (LVM-242W), Eas
y
to
operate OSD user inter
f
ace, Rack Mountable desi
g
n.
M
ulti Format LCD Monitor
0
6

Name & Function of Each Part
L
VM-172W FR
O
N
T
[
ANALOG] Button/Lamp
- Used to select desired Analog input. (CVB1/2/3, S-Video, Component, RGB
)
- Press t
h
e
b
utton to activate t
h
e ana
l
o
g
input menu-se
l
ection, t
h
en use UP an
d
DOWN
b
utton to se
l
ect
desired in
p
ut.
* See section “Other Functions [1]ANALOG Button” for more information.
[
DVI
]
Button/Lamp
- Use
d
to se
l
ect
d
esire
d
DVI in
p
ut.
- Press the button to activate the DVI input menu selection, then use UP and DOWN button to select
d
esire
d
input
.
* See section “Other Functions
[
2
]
DVI Button”
f
or more in
f
ormation.
[
SDI-A
]
/
[
SDI-B
]
Button/Lam
p
- Use
d
to se
l
ect SDI-A/SDI-B input
.
[
SCAN]
b
utton/
l
amp
- Used to change the scan mode. Press the button to activate through the scan modes: OVER SCAN -> USER
A
S
PE
C
T -> ZER
O
SC
AN -> UNDER
SC
AN -> 1:1
SC
AN -> FIT WIDTH
* See section “Other Functions
[
3
]
SCAN Button”
f
or more in
f
ormation.
#[USER ASPECT] : User can adjust width and height of the displa
y.
* See section “Other Functions [4] Pixel to Pixel and [5] User As
p
ect”
f
or more in
f
ormation.
[
ASPECT] Button/Lam
p
- Used to change the displa
y
ratio between 4:3 and 16:9.
* Display ratio locks to 16:9 if the display ratio of input signal is 16:9
.
PO
WER
A
NAL
O
G
S
DI-A
S
DI-B
DV
I
SC
A
N
AS
PE
C
T
MARKER
ENTER
UP
/
DOWN
M
ENU
T
C
(
TIME CODE
)
PHA
SE
BLUE
O
NLY
/
M
O
N
O
H
/
V DELA
Y
T
A
L
L
Y
L
L
AP
E
R
T
UR
E
B
RIGHT
C
HR
O
MA
CO
NTRA
ST
V
OLUME
M
u
l
ti Format LCD Monitor
07

[
MARKER] Button/Lam
p
- Used to activate/deactivate the Marker. The type o
f
marker at work may be selected on the main menu.
[
H/V DELAY] button/lam
p
- Use
d
to c
h
ec
k
h
orizonta
l
s
y
nc an
d
vertica
l
s
y
nc simu
l
taneous
ly
.
[
BLUE ONLY
]
/
[
MONO
]
Button/Lamp
- Activates in the order o
f
[O

]-[Blue Only]-[Mono]-[Focus Assist]-[O

]
- Press the button to remove red and green from the input signal and displa
y
the screen onl
y
under a blue
si
g
na
l
.
Press the button again to activate mono mode. The
y
are not available in RGB, DVI ANALOG, DVI DIGITAL
a
n
d
HDMI m
odes.
# [Focus Assist] : Focus assist su
pp
ort
f
eature.
Use [Chroma] knob to control the sensitivity level(0~80) of Focus Assist. Maximum value is 80.
[
PHASE] Button
- Used to activate PHASE and Closed Caption
f
eature and use UP/DOWN buttons to toggle through the values.
- Feature activates dierentl
y
in dierent input mode
:
- SDI-A/B in
p
ut : Closed Ca
p
tion.
- Composite/S-Vi
d
eo input : PHAS
E
[
T.C
]
Button/Lam
p
- Used to activate Timecode (VITC,LTC) display
f
eature.
- Press the button once to activates VITC and press again to activate LTC
.
[
MENU
]
Button
-
Used
to
act
iv
ate
the
m
a
in
OS
D M
e
n
u.
[
UP] Button
- Used to move within the menus during OSD menu activation and is also used to increase the value o
f
selected feature.
- In Pixel to Pixel mode, press the button to rotate the display clockwise. (LVM-172W)
[
DOWN
]
Button
- Used to move within the menus durin
g
OSD menu activation and is also used to decrease the value of the
se
l
ected
featu
r
e.
- in Pixe
l
to Pixe
l
mo
d
e, press t
h
e
b
utton to rotate t
h
e
d
isp
l
a
y
s counterc
l
oc
k
wise. (LVM-172W)
[
ENTER
]
Button
-
Used
to
co
n

rm
a
c
h
ose
n v
a
l
ue.
[
POWER] Button
- Power On/O

button. LED lights in Red when the power is O

and lights in Green i
f
the signal is normal. I
f
the signal is unsupported or disconnected, LED ashes in yellow.
[
TALLY]
- Tally lamp that can be toggled in green or red using the REMOTE(RJ-45) port or RS-422 serial communication.
[
APERTURE
]
Knob
- Use
d
to a
d
just t
h
e picture s
h
arpness. T
h
e va
l
ue is se
l
ecta
bl
e
b
etween -12 ~ 12
.
#Aperture is not available in DVI Analog or Graphic mode.
Name & Function of Each Part
M
u
l
t
i F
o
rm
at
L
C
D M
o
ni
to
r
08

L
VM-242W FR
O
N
T
[
BRIGHT
]
Knob
- Used to adjust the degree of brightness. - The value is selectable between -128 ~ 127.
[
CHROMA
]
Knob
- Used to ad
j
ust the saturation o
f
the image. - The value is selectable between -128 ~ 127.
# This feature is not available in DVI Graphic mode and DVI Analog.
[
CONTRAST
]
Kno
b
- Use
d
to a
d
just t
h
e contrast.
- Th
e
v
a
l
ue
i
s
se
l
ectab
l
e
bet
w
ee
n -12
8
~ 127
.
[
VOLUME
]
Knob
- Used to adjust the volume for internal speaker and external output
.
- Th
e
v
a
l
ue
i
s
se
l
ectab
l
e
bet
w
ee
n
0
~ 2
0.
[
ANALOG] Button/Lamp
- Used to select desired Analog/DVI input. (CVB1/2/3, S-Video, Component, RGB, DVI Digital, DVI Analog
)
- Press t
h
e
b
utton to activate t
h
e ana
l
o
g
input menu-se
l
ection, t
h
en use UP an
d
DOWN
b
utton to se
l
ect
desired in
p
ut.
[
SDI-A] / [SDI-B] Button/Lam
p
- Use
d
to se
l
ect SDI-A/SDI-B input
.
[
SCAN
]
Button/Lamp
- Use
d
to c
h
an
g
e t
h
e scan mo
d
e. Press t
h
e
b
utton to activate t
h
rou
gh
t
h
e scan mo
d
es: OVER SCAN -> USER
A
S
PE
C
T -> ZER
O
SC
AN -> UNDER
SC
AN -> 1:1
SC
AN -> FIT WIDTH
* See section “Other Functions [3]SCAN Button”
f
or more in
f
ormation.
# [USER ASPECT] : User can adjust width and height o
f
the displa
y
.
* See section “Other Functions [4] Pixel to Pixel and [5] User Aspect” for more information.
A
NAL
O
G
S
DI-
A
S
DI-B
S
CAN
A
S
PE
CT
M
A
R
KE
R
H/V DELAY
POWE
R
ENTER
/
VO
L
UP
/CO
NTRA
S
T
DOWN
/
BRIGH
T
M
EN
U
C
HR
O
MA
/
PHA
S
E
BLUEONLY
/
MONO
T
A
L
L
Y
L
L
Name & Function of Each Part
Mu
l
ti Format LCD Monitor
09

[
ASPECT] Button/Lam
p
- Used to change the displa
y
ratio between 4:3 and 16:9.
* Display ratio locks to 16:9 i
f
the display ratio o
f
input signal is 16:9
.
[
MARKER] Button/Lam
p
- Used to activate/deactivate the Marker. The t
y
pe o
f
marker at work ma
y
be selected on the main menu.
[
H/V DELAY] button/lam
p
- Use
d
to c
h
ec
k
h
orizonta
l
s
y
nc an
d
vertica
l
s
y
nc simu
l
taneous
ly
.
[
BLUE ONLY]/[MONO] Button/Lamp
- Activates in the order o
f
[O

]-[Blue Only]-[Mono]-[Focus Assist]-[O

]
- Press the button to remove red and green from the input signal and displa
y
the screen onl
y
under a blue
signal.
Press t
h
e
b
utton a
g
ain to activate mono mo
d
e.
They are not available in RGB, DVI ANALOG, DVI DIGITAL and HDMI modes.
# [Focus Assist] : Focus assist support feature.
Use [Chroma] knob to control the sensitivity level(0~80) o
f
Focus Assist. Maximum value is 80.
[
CHROMA/PHASE] Button/Lam
p
- Used to activate PHASE and Closed Caption
f
eature and use UP/DOWN buttons to toggle through the values.
- Feature activates dierentl
y
in dierent input mode
:
- SDI-A/B in
p
ut : Closed Ca
p
tion.
- Composite/S-Vi
d
eo input : PHAS
E
[
MENU] Button
-
Used
to
act
iv
ate
t
h
e
m
a
in
OS
D M
e
n
u.
[
DOWN/BRIGHT
]
Button
- Used to move within the menus during OSD menu activation and is also used to decrease the value of the
se
l
ected
featu
r
e.
- It ma
y
also be used to control the bright value when the OSD menu is inactivated.
[
UP/CONTRAST
]
Butto
n
- Used to move within the menus durin
g
OSD menu activation and is also used to increase the value o
f
se
l
ected
featu
r
e.
- It ma
y
a
l
so
b
e use
d
to contro
l
t
h
e contrast va
l
ue w
h
en t
h
e OSD menu is inactivate
d.
[
ENTER] Button
- Used to con

rm a chosen value (or mode)
.
- It ma
y
also be used for shortcut access to volume control when OSD menu is inactivated.
[
POWER
]
Button
- Power On/O

button. LED lights in Red when the power is O

and lights in Green i
f
the signal is normal.
If the signal is unsupported or disconnected, LED ashes in
y
ellow
.
[
TALLY
]
Lam
p
- Ta
ll
y
l
amp t
h
at can
b
e togg
l
e
d
in green or re
d
using t
h
e REMOTE(RJ-45) port or RS-422 seria
l
communication.
M
u
l
t
i F
o
rm
at
L
C
D M
o
ni
to
r
1
0
Name & Function of Each Part