TW Audio SFV20 User manual

Assembly
Instructions
SFV20

Assembly Instructions SFV20
2
Introduction
The SFV20 rigging frame is an accessory for the VERA20 loudspeaker.
It is characterized by a subtle look, a remarkable size to weight ratio and ease of use.
Instructions in this setup manual
NOTE
TIP
CAUTION
WARNING
Thank you for choosing a high-quality product “MADE IN GERMANY” from the brand
TW AUDiO.
If you lend your product to another party, inform that party of the safety-related operating pro-
cedures and hand over this assembly guide. If you require additional copies of this manual,
you can obtain them free of charge from TW AUDiO or download them from www.twaudio.de
Strictly adhere to the instructions contained in this operating manual that are marked as
follows:
This symbol in combination with the signal word “Warning” identifies a potentially hazardous
situation. Failure to comply with this safety instruction can lead to serious injury or even death.
This symbol in combination with the signal word “Caution” identifies a potentially hazardous
situation. Failure to comply with this safety instruction can lead to light or moderate injury.
This symbol in combination with the signal word “Note” identifies a potentially hazardous
situation. Failure to comply with this safety instruction can lead to product damage.
This symbol in combination with the signal word “Tip” identifies additional information or
notes that will simplify working with TWAUDiO products on the basis of practical experience.

Assembly Instructions SFV20
3
Notes on the products
Read manual
before use!
Before using the rigging frame, carefully read the assembly instructions and keep the instruc-
tions in a safe place together with the SFV20 rigging frame.
General Information
Assembly Guide: OM-SFV20
Version 2.0 d, 11/2022
© by TWAMBO 2022; all rights reserved.
All information contained in this operating manual was correct to the best of our knowledge
at the time of printing.
Quality warranties or assurance of suitability for a certain type of use based on the technical
specifications, dimensions and weights are not granted by TWAMBO.
TWAMBO also shall not assume liability for any secondary damage (property damage and/or
personal injury) nor for the failure to comply with this operating manual!
TWAMBO reserves the right to update this document based on recent developments.
TWAMBO GmbH
Karl-Hofer-Str. 42
14163 Berlin
Germany
Phone : + 49 (0) 71 41-48 89 89 0
Fax: + 49 (0) 71 41-48 89 89 99
E-Mail: [email protected]
WWW: www.twaudio.de

Assembly Instructions SFV20
4
Table of contents
1. Safety | Intended use...................................................................................................... 5
2. Overview ........................................................................................................................ 7
2.1 Components ........................................................................................................... 7
3. Technical specifications .................................................................................................. 8
3.1 Data sheet............................................................................................................... 8
4. Commissioning............................................................................................................... 9
4.1 Setup ...................................................................................................................... 9
4.2 Wind load ................................................................................................................ 9
4.3 Secondary safety component ................................................................................ 10
4.4 Preparing VERA20 loudspeaker for rigging ............................................................ 11
4.5 Using the VERA LA900 load adapter...................................................................... 14
4.6 Mounting the VERA20 loudspeaker ....................................................................... 16
4.7 VERA20 setup from the second speaker set.......................................................... 21
4.8 Compression mode ............................................................................................... 29
5. Transport and Storage.................................................................................................. 30
6. CE Declaration of Conformity........................................................................................ 31
7. Disposal ....................................................................................................................... 31

Assembly Instructions SFV20
5
1. Safety | Intended use
The SFV20 rigging frame was developed for use in professional sound systems. The rig-
ging frame may only be used by trained and qualified personnel.
Before each installation, check the integrity of the SFV20 rigging frame and ensure that all
components are in perfect condition.
The scope of delivery includes specified quick-locking pins and a specified load adapter with
shackle. Only use this components.
WARNING
The SFV20 rigging frame may only be used with the VERA20 loudspeaker.
These assembly instructions describe how to use the SFV20 rigging frame. Any other use
shall be deemed improper and may result in damage or even injury.
Modifications or alterations to individual parts of the SFV20 rigging frame are not permitted!
Danger to life!
WARNING
During and after each system setup, check that all quick-locking pins are always completely
inserted! All quick-locking pins must always be used!
WARNING
The SFV20 is an accessory designed both for indoor and outdoor use.
CAUTION
The SFV20 rigging frame may only be used by trained and qualified personnel.
Personnel must check the SFV20 for its full suitability before each use.
WARNING
When visible damage to any part of the SFV20 rigging frame is detected, it must be decom-
missioned immediately.
WARNING
Please adhere to the following safety instructions to avoid risks when using accessories.
Note the operating modes described in this assembly instructions. Other uses are not per-
missible.
Damage caused by improper use is not covered by TWAMBO.

Assembly Instructions SFV20
6
WARNING
Before mounting the SFV20 rigging frame, all attachment points - such as ceilings and cross-
beams - must be checked for full load capacity and stability.
The SFV20 accessory is specified for a load of not more than nine VERA20 loudspeakers.
This load capacity must never be exceeded!
When working with heavy loads over 20 kg [44,09lbs.], use suitable aids (dollies, hoisting
slings, etc.). Multiple persons may be required depending on the situation.
When moving (mounting, removing, servicing) the SFV20 rigging frame with VERA20 loudspe-
akers, ensure that there is enough room to avoid collisions with other objects.
When installing the SFV20 rigging frame, be careful not to pinch or twist the power cables
or other cables of the VERA20 loudspeakers! The respective national electrotechnical regu-
lations apply.
Every time you install the SFV20 rigging frame, check all screw connections. Tighten all loose
screws. If this is no longer possible, the screws must be replaced.
WARNING
WARNING
CAUTION
WARNING

Assembly Instructions SFV20
7
2. Overview
2.1 Components
1. SFV20 rigging frame - Surface powder-coated
2. VERA LA900 Load adapter with shackle
3. Captive Quick-locking pins
Figure 2.1 - Overview
12 3
3
When the SFV20 rigging frame is delivered from the factory, the quick-locking pins are in
„Storage Position“.
NOTE

Assembly Instructions SFV20
8
3. Technical specifications
3.1 Data sheet
maximum load capacity
230 kg [507.1lbs] at safety factor 10 before
breacking point correspond to e.g. 9 VERA20
elements
Dimensions (h x w x d) 100 x 550 x 600 mm [3.94 x 21.65 x 23.62in]
Weight 6,8 kg [15 lbs.]
Surface Powder-coated
Maximum length of system setup,
without subwoofer 2,70 m [8.86 ft.]

Assembly Instructions SFV20
9
4. Commissioning
4.1 Setup
The SFV20 rigging frame is designed for hanging operation. TWAUDiO provides a wide range
of accessories to securely attach the module to crossbeams, motor lifts, etc. in a suspended
position.
TW AUDiO recommends using only the accessories specified by TWAUDiO for securing and
mounting the rigging frame.
NOTE
WARNING
WARNING
Please note that setting up the system setups always requires two persons!
4.2 Wind load
WARNING
Make sure that the system structures are not operated over the audience at wind speeds in
excess of 6 bft (22 to 27kn / 39 to 49kph / 24.2 to 30.45mph) and that there are no persons
in the immediate vicinity of the system structure!
Before setting up the system outdoors, consider unexpected wind conditions at the opera-
tion site!
Disassemble your system immediately when wind speeds exceed 8 bft (34 to 40kn / 62 to
74 kph / 38.5 to 46mph) and secure the system components!
Make sure that there are no persons in the immediate vicinity of the system structure!

Assembly Instructions SFV20
10
4.3 Secondary safety component
Figure 4.3.1 - Secondary safety component
For the second independent safety component, attach another VERALA900 load adapter
with shackle at point D to the rigging frame. Mount it directly behind the first load adapter.
Attach both VERA LA900 load adapter using two quick-locking pins each to the SFV20 rig-
ging frame!
Secure the complete system, for example using safety chains!
D
Figure 4.3.2 - Secondary safety component example
safety main load
NOTE
WARNING
For the secondary safety component, the respective national electrotechnical regulations apply.