TYLZA KMJ01-30 Troubleshooting guide

UNDER CABINET RANGE HOOD
Model:KMJ01-30"/ KMJ01-36"
Installation Guide ＆ Users Manual
NOTICE:
For residential use only.
Installer: Leave this guide with the homeowner.
Homeowner: Keep this guide for future reference.
Email address：[email protected]
Phone number: [phone]

2 3
THANK YOU FOR YOUR PURCHASE
Thank you for your purchase. We know that you have many brands and
products to choose from and we are honored to know that you have decided
to take one of our products into your home and hope that you enjoy it.
TYLZA appliances are designed according to the strictest safety and
performance standard for the North American market. We follow the most
advanced manufacturing philosophy. Each appliance leaves the factory after
thorough quality inspection and testing. We are ready to answer any
questions you may have regarding how to install, use and care for your
products. We hope that this manual will help you learn to use the product in
the safest and most effective manner .
If you have any questions or concerns, please contact our Customer Support at:
[email protected]
TABLE OF CONTENTS
SAFETY INSTRUCTIONS 4
ALUMINUM FILTERS 5
PARTS DIAGRAM 6
INSTALLATION REQUIREMENTS 7
PRE-INSTALLATION PROCEDURES 8
INSTALLATION INSTRUCTIONS 9-10
PREPARING THE VENT HOOD:AIR RECIRCULATION MODE
OPERATING INSTRUCTIONS
MAINTENANCE
TROUBLSHOOTING
MEASUREMENNTS ＆ DIAGRAMS
WARRANTY & SERVICE
PREPARING THE VENT HOOD: AIR EXTRACTION MODE
11
13
12
14
15
16
17

4 5
Read all instructions before using this appliance.
Save these instructions for future references
Approved for residential appliances
For residential use only
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
FOR GENERAL VENTILATING USE ONLY. DO NOT USE
TO EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS
OR VAPORS.
WARNING
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of an electrical
short circuit, grounding reduces the risk of electric shock by
providing an escape wire for the electric current. This appliance
is equipped with a cord having a grounding wire with a grounding
plug. The plug must be plugged into an outlet that is properly
installed and grounded.
WARNING - IMPROPER GROUNDING CAN
RESULT IN A RISK OF ELECTRIC SHOCK.
Consult a qualified electrician if the grounding instructions are
not completely understood, or if doubt exists as to whether the
appliance is properly grounded.
Do not use an extension cord. If the power supply cord is too
short, have a qualified electrician install an outlet near the
appliance.
CAUTION
To reduce risk of fire and to properly exhaust air, do not
vent exhaust air into spaces within walls, ceilings, attics,
crawl spaces, or garages.
WARNING
TO REDUCE THE RISK OF FIRE, USE ONLY METAL
DUCT WORK. Install this hood in accordance with all
requirements specified.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO
PERSONS, OBSERVE THE FOLLOWING:
Use this unit only in the manner intended by the
manufacturer. If you have questions, contact the
manufacturer
B. Before servicing or cleaning the unit, switch power
off at service panel and lock service panel disconnecting means to prevent
power from
being switched on accidentally. When the service disconnecting means
cannot be locked, securely fasten a prominent warning device, such as a
tag, to the service panel.
C. Installation Work and Electrical Wiring Must Be Done
By Qualied Person(s) In Accordance With all Applicable Codes &
Standards, Including Fire-rated Construction.
A.
E.
F.
D. Sufcient air is needed for proper combustion and
exhausting of gases through the ue (Chimney) of fuel burning equipment to
prevent back- drafting. Follow the heating equipment manufacturers
guideline and safety standards such as those published by the National Fire
Protection Association (NFPA), the American Society for Heating,
Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code
authorities.
When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden utilities.
Ducted systems must always be vented to the outdoors.
WARNING
To Reduce The Risk Of Fire Or Electric Shock, Do Not Use This Hood
With Any External Solid State Speed Control Device.
WARNING
WARNING
Unplug or disconnect the appliance from the power supply
before servicing.
TO REDUCE THE RISK OF INJURY TO PERSONS, IN THE EVENT OF A
RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING:
A. SMOTHER FLAMES with a close - fitting lid, cookie sheet, or other metal
tray, then turn off the gas burner or the electric element. BE CAREFUL TO
PREVENT BURNS. If the flames do not go out immediately, EVACUATE
AND CALL THE FIRE DEPARTMENT.
B. NEVER PICK UP A FLAMING PAN - you maybe DO NOT USE WATER,
including wet dishcloths or towels - a violent steam explosion will result.
Always leave safety grills and filters in place.Without these components,
operating blowers could catch onto hair, fingers and loose clothing.
The manufacturer declines all responsibility in the event of failure to observe
the instructions given here for installation,maintenance and suitable use of the
product. The manufacturer further declines all responsibility for injury due to
negligence and the warranty of the unit automatically expires due to improper
maintenance.
ALUMINUM FILTERS
About Your New Filters
Aluminum Filters are recommenGed to be replaced every 6 months depending on
usage.
Cleaning my Aluminum Filters
Your filters can be hand washed and cleaned to increase time between
replacements. Aluminum Filters may not be placed in the dishwasher.
IMPORTANT SAFETY INSTRUCTIONS

6 7
PARTS DIAGRAM
MODEL: KMJ01-30"KMJ01-36"
Other accessories:
INSTALLATION REQUIREMENTS
WARNING
Sufficient air is needed for proper combustion and exhausting of gases through the chimney of fuel burning equipment to
prevent back- drafting. Follow the cooking equipment manufacturers guideline and safety standards such as those published
by the National Fire Protection Association (NFPA), the American Society for Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE), and local code. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other
hidden utilities. Ducted systems must always be vented outdoors.
1.Please read the following instructions carefully.
2.This Range Hood can be vented through the top or back. Remove the Air Outlet Cap
according to the option chosen (Fig. 1). For ductless installation, install an Air Outlet
Cap on both the rear and top vent holes.
3.For optimal performance the Range Hood must be installed 24" - 36" in height from
the cooktop. (Fig. 2)
4.Electrical Requirements: Rated Voltage and Frequency:) 110-120V~ 60Hz. Motor Input
Power: 65W
1. 3-Speed Mechanical Control
2. Main Body
3. Motor Housing
4. LED Lights (2 pcs)
5. Aluminum Filter (2 pcs)
6. Carbon Filter (2 pcs)
7. Smoke tube (1 pcs)
8. Duct Clamps (1 pcs)
9. Duct Connection Fitting with Damper(1 pcs)
10. Air Outlet Cap (2 pcs)
11. Screws 5mm x 49mm (4 pcs)
12. Wall Anchors 10mm x 43.3mm (4 pcs)
TOOLS NEEDED FOR INSTALLATION

8 9
PRE-INSTALLATION PROCEDURES
• Please read the instructions carefully. Unpack the Range Hood and check that all
functions are working before installing.
•Ensure that the voltage (V) and the frequency (Hz) indicated on the sticker match the
voltage and frequency at the installation site.
•Check that the area behind the installation surface to be drilled is clear of any electrical
cables or pipes, etc.
• The stainless steel surfaces of the Range Hood are very easily damaged during
installation if scratched or bumped by tools. Please take care to protect the surfaces
during installation.
• Protect the cook top surface below with cardboard, or the like, to prevent damage
occurring during installation.
• The manufacturer shall not be held liable for failure to observe all safety regulations.
INSTALLATION INSTRUCTIONS
Cabinet Installation Method
1.
2. Use the 4 screws to mount the Range Hood to the
cabinet. Check that your mounting screws are in
the correct place by temporarily fitting the Range
in place. If correct, lock into position by pushing in
the Range Hood.
For Ducted installation drill a 130mm diameter hole
into the cabinet and four 3.5mm diameter holes as
pictured below picture.
For Ductless installation do not drill the 130mm
diameter hole in the cabinet. Drill only the four
3.5mm diameter holes as pictured below.
CAUTION: HOOD MAY HAVE VERY SHARP EDGES; PLEASE WEAR
PROTECTIVE GLOVES WHENEVER IT IS NECESSARY TO REMOVE ANY
PARTS FOR INSTALLING, CLEANING OR SERVICING.
IMPORTANT READ BEFORE INSTALLATION
You will need to set the Range Hood mode to either Ducted or Ductless.
1.Remove Aluminum Filters
2.Locate Knob Settings located under the Motor (Fig. 1)
3.Unlock the Settings Knob by unscrewing and setting to Ducted or Ductless mode.
4.Lock the Knob into place by replacing the screw from Step 3.
Fig.1

10 11
INSTALLATION INSTRUCTIONS
CAUTION: HOOD MAY HAVE VERY SHARP EDGES; PLEASE WEAR
PROTECTIVE GLOVES WHENEVER IT IS NECESSARY TO REMOVE ANY
PARTS FOR INSTALLING, CLEANING OR SERVICING.
Wall Mount Installation Method
1. A. Find the 4 mounting holes in the back of the
range hood. Mark their locations at the installation
location with a pencil or marker.
B. Drill 5/16 (8mm) hole at each of the marked
locations.
C. Insert anchors along with screws into each drilled
hole. Firmly tighten the screw into place.
D. Hang your Range Hood into place by aligning the
screws with the 4 mounting holes in the back of the
range hood. Lock into place by sliding down the
range hood.
PREPARING THE VENT HOOD:
AIR RECIRCULATION MODE
Installing the Carbon Filter
1.) Remove the aluminum filters.
2.) The charcoal filter is installed at the end of the motor.Align the
upper and lower holes , twist the carbon filter Counterclockwise
to lock into place.
3.) To replace the carbon filter, reverse the process and repeat.
NOTE: The carbon filter cannot be washed and reused and
must be replaced every 4-6 months, depending on use.
If you have any questions about Installing the Carbon Filter,
please feel free to contact our Customer Support at:
[email protected], and we will provide you with the video to
install it properly.

1213
PREPARING THE VENT HOOD:
AIR EXTRACTION MODE
Check Valve Installation and Plugs
If you have any questions about the Installing the Duct Connection Fitting
with Damper, please feel free to contact our Customer Support at:
[email protected], and we will provide you with the video to install it
properly.
OPERATING INSTRUCTIONS
Turns the range hood ON/OFF.

MAINTENANCE
CAUTION: NEVER PUT YOUR HAND INSIDE OF THE UNIT WHILE ITS OPERATING.FOR
THE BEST PERFORMANCE CLEAN YOUR
RANGE HOOD REGULARLY.
CLEANING
1. Use only mild soap or cleaning solutions to clean the hoods'
outer surface. Dry surfaces using a soft cloth.
2. Stainless Steel cleaner may be used on the external surface.
3.Clean the Range Hood assembly 3 to 6 months depending on use.
4.DO NOT clean the motor or electrical components with water or
any other liquid.
Replacing LED 2W 120V Light Fixture
1. Remove the aluminum filters
2. Make sure the range hood is unplugged or turn OFF breaker and the
lights are cool to touch.
3. Place a flat-head screwdriver between light housing and hood body.
4. Gently pry up the light housing and search for the metal clip.
5. Apply force to the metal clip and pull out the light fixture.
6. Disconnect the power cable and discard the old light fixture.
7. Reverse the steps to install a new LED light fixture.
8. Reinstall the aluminum filters.
9. Turn ON breaker and range hood to test for operation.
10. If you have questions about the replacing of LED Light, please contact
us at: [email protected], and we will help you in time.
14
TROUBLESHOOTING
CAUTION: ALWAYS UNPLUG UNIT FROM POWER BEFORE SERVICING
PROBLEM SOLUTION TOOLS
My range hood is
noisy.
A. Check inside the range hood
for any loose debris and remove. Phillips Screwdriver
My range hood has
poor performance.
A. The range hood and cook top
are too far away from each other.
Optimal distance is 24” to 36”
B. There are too many open
windows or doors in the area.
Close some doors or windows.
C. The motor performance has
decreased due to wear. Replace
motor.
D. Check and make sure the tape
holding down the damper flaps at
the vent hole are removed before
use.
Phillips Screwdriver
My range hood
shakes.
A. The installation is not secure.
Check again and make sure the
installation hardware is securely
mounted.
B. The fan is broken or not
balanced. Realign or replace fan.
C. The motor is loose. Check and
make sure the motor is solidly
mounted to the unit.
Phillips Screwdriver
The motor no longer
runs.
A. Replace control panel or
circuit board.
B.Replace with new motor
assembly.
Phillips Screwdriver
Light bulb went out. A. Replace with a new LED Bulb
2watt max. Phillips Screwdriver
15

1617
MEASUREMENNTS ＆ DIAGRAMS
***All inch measurements are converted from millimeters.Inch measurements are estimated.
***All measurements in ( ) are millimeters.

Correct Disposal of this product:
This marking indicates that this appliance should not
be disposed with other household wastes. To prevent
possible harm to the environment or human health
from uncontrolled waste disposal, recycle it responsibly to
promote the sustainable reuse of material resources.