ubabub Nifty User manual

Timber 3-IN-1 Cot
Product Code: UU0310
Nifty
revised 24FEB17

2
Nifty
Domestic child cot
Timber model
Instruction manual
Congratulations and
thank you for purchasing
an Ubabub product.
With our entire range of
clearly modern nursery
furniture, we are developing
cots that have the capacity
to convert into a junior
bed and adapt with your
growing child. During the
design and production
of this product we have
selected materials that are
either recyclable or derived
from sustainable practices.
PERSONS REQUIRED ASSEMBLY TIME
TOOLS REQUIRED
– PHILLIPS HEAD SCREWDRIVER
– ALLEN KEY (SUPPLIED)
Contents
Contents & Hardware 3
Warning, Care & Maintenance 5
ALower rails position 10
BFront/Back panels position I 11
CFront/Back panels position II 12
DEnd panel assembly 13
EBaseplate assembly 14
FMattress support position 15
GClose extra holes 16
HFinished assembly 17

3
Contents
(A) Left End
Panel x 1
(B) Right End
Panel x 1 (C) Front Panel x 1
(D) Back Panel x 1
(E) Mattress Support x 1
(F) Front Lower Rail x 1 (G) Back Lower Rail x 1

4
Hardware
(H9) Allen Key x 1
(H4) 1.5cm Round
Head Bolt x 16
(H8) Support Plate x 4(H7) Wood Dowel x 4
(H2) 3.2cm Allen
Head Bolt x 12
(H1) 5.7cm Allen
Head Bolt x 8
(H3) 1.5cm Allen
Head Bolt x 4
(H6) Lock Washer x 20(H5) Washer x 20

5
WARNING:
Failure to follow these warnings and
the assembly instructions could result
in serious injury or death.
READ ALL INSTRUCTIONS BEFORE ASSEMBLING
COT. KEEP THE MANUAL FOR FUTURE USE.
WARNING:
Parents should ensure a safe environment for the child by
checking regularly, before placing the child in the product,
that every component is properly and securely in place.
Please do NOT remove any wood screws in the normal disassembly
of the cot.
WARNING:
CAUTION: ANY MATTRESS USED IN THIS COT MUST BE
AT LEAST 27 1/4 INCHES (69CM) BY 51 5/8 INCHES (131CM)
WITH A THICKNESS NOT EXCEEDING 6 INCHES (15CM).
Please read the Caution and
Warning Statements insert
before using your cot.

6
RECOMMENDEDMATTRESS SIZE:
This cot has been manufactured for use
with a mattress which measures 690 mm
wide by 1310 mm long and 150 mm (or
less) in thickness. The width and length
are specified because it is important that
the gaps between the mattress and the
sides and ends of the cot will not exceed
40 mm when the mattress is pushed to
one side or end, and 20 mm when the
mattress is centred in the cot. This is to
minimize the risk of a child’s limb becom-
ing caught in the gap. The thickness of
the mattress has been specified to
ensure that the depth of the cot is greater
than 500 mm with the mattress base in
the lower position to minimize the risk of a
child climbing or falling out of the cot.
WARNING:
TO PREVENT FALLS, THE MATTRESS BASE OF THIS
COT SHOULD BE ADJUSTED TO THE LOWEST
POSITION BEFORE THE CHILD CAN SIT UP.

7
• Do not use this cot if you cannot exactly follow the accompanying instructions.
• Infants can suffocate on soft bedding. Never add a pillow or comforter. Never
place additional padding under an infant.
• To reduce the risk of SIDS, pediatricians recommend healthy infants be placed
on their backs to sleep, unless otherwise advised by your physician.
• Strangulation Hazard: Strings can cause strangulation! Do not place items with
a string around a child’s neck, such as hood strings or pacifier cords. Do not
place cords, straps, or similar items that could become wound around the child’s
neck in or near this cot. Do not suspend strings over a cot or attach strings to
toys.
• To help prevent strangulation tighten all fasteners. A child can trap parts of the
body or clothing on loose fasteners.
• DO NOT place a cot near a window where cords from blinds or drapes may
strangle a child. Do not place this cot near a window or a patio door where a child
could reach the cord of a blind or curtain and be strangled.
• Fall Hazard: When a child is able to pull to a standing position, set the mattress
to the lowest position and remove bumper pads, large toys and other objects that
could serve as steps for climbing out.
• Do not use this cot if the child is able to climb out unaided or is taller than 35 in.
(89cm).
• Check this product for damaged hardware, loose joints, loose bolts or other
fasteners, missing parts or sharp edges before and after assembly and frequently
during use. Securely tighten loose bolts and other fasteners. DO NOT use cot if
any parts are missing, damaged or broken. DO NOT substitute parts. Contact
Ubabub for replacement parts and instructional literature if needed.
• DO NOT use a water mattress with this cot.
• If refinishing, use a non-toxic finish specified for children’s products.
• Never use plastic shipping bags or other plastic films as mattress covers
because they can cause suffocation.
• Infants can suffocate in gaps between cot sides when used with a mattress that
is too small.
• Follow warnings on all products in a cot.
• Ensure that the sides are properly latched or locked in place when the cot is
occupied.
• Place cot at a reasonable distance from curtains, blinds, heater and power
points.
• Keep medication, string, elastic, small toys or small items, such as money, out
of reach from any position in the cot.

8
Storage:
Care and Maintenance:
• Solid woods exchange moisture with the air adjusting to major
changes in room temperature and humidity. Therefore, it is best to
place your furniture away from heating or air- conditioning vents.
• Sunlight is not friendly to solid wood furniture and prolonged
direct exposure to harsh sunlight can discolor the finish. Be careful
not to place your furniture in direct sunlight for extended periods
of time. As with all your fine furniture, blot up spills immediately.
• Do not scratch or chip the finish. Do not use abrasive chemicals
for cleaning. Clean with mild soap on a soft rag. Rinse and dry
thoroughly. If you ever refinish this furniture, be sure to use only
a non-toxic finish specified for children’s products. If you choose
to refinish this furniture, the warranty will be voided.
• Wipe up spills immediately with a soft, clean cloth.
• Urine spills can cause discolouration and is a growth medium to
mould fungus.
• Do not use strong household cleaners, and in particular do not
use any petro-chemical based cleaners on any plastic or wood
surface.

9
AUSTRALIA - WARRANTY
Ubabub warrants that your Nifty Timber 3-IN-1 Cot will be free from
defects the whole product for a period of one year, from the date of
purchase. This warranty only applies where the product is completely
and correctly assembled and used in accordance with all accompanying
recommendations and users instructions. This warranty is in addition to
your rights under the Australia Consumer Law.
This warranty will no longer apply where the defect is a result from
installation and assembly, normal wear and tear, abuse, negligence,
improper use or alteration to the finish, design, and hardware of the
cot.
Our goods come with guarantees that cannot be excluded under the
Australian Consumer Law. You are entitled to a replacement or refund
for a major failure and compensation for any other reasonably foresee-
able loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.
Please retain your receipt as proof of purchase and contact Ubabub for
further assistance on how to process any warranty claims.
Business name: Ubabub International Pty Ltd
Business address: PO Box 1149 Collingwood VIC 3066
Phone number: [phone]
Email address: [email protected]
Manufacture name: Associate Yang Vietnam Enterprise Co., Ltd
Manufacture address: No. 22, 2A Street Industrial Zone Bien Hoa II,
Bien Hoa City, Dong Nai Province, Vietnam
Contact us:
Ubabub International Pty Ltd
PO Box 1149 Collingwood VIC 3066
[phone]
[email protected]
www.designkids.com.au

10
ALower rails position
H7 X2
H6
H5
H2
B
F
G

11
BFront/Back panels position I
H6
H5
H2
X4
F
G
C
D
B

12
CFront/Back panels position II
X4
H6H5
H1
F
G
C
D
B

13
DEnd panel assembly
F
G
B
A
C
X2
H6
H5
H2
H7
H6
H5
H2
X4
D

14
EBaseplate assembly
H8
X4
F
G
B
A
H4
H4
H4 H4

15
FMattress support position
* Make sure the mattress support (E)
is installed FLAT SIDE UP.
* Make sure the mattress support (E)
is level.
B
A
X4
H6
H5
H1 E

16
GClose extra holes
B
X4
H3
A
E
CARE AND SAFETY:
THIS UNIT IS SUPPLIED WITH EXTRA BOLTS THAT SECURES THE HOLES ACCESSIBLE TO THE CHILD.
FAILURE TO USE THIS COULD RESULT IN A HAZARD. WE RECOMMEND THAT YOU USE THIS
SAFETY DEVICE.
When putting the mattress support (E) at the higher position, use the provided bolts (H3) and
plug the corresponding holes at the lower position as illustrated. Tighten each bolt with the
Allen wrench (H9). You will install a total of 4 bolts.
If putting the mattress support (E) at the lower position, use the provided bolts (H3) and plug
the corresponding holes at the higher position. Tighten each bolt with the Allen wrench (H9).
You will install a total of 4 bolts.

17
KEEP THIS MANUAL IN A SAFE PLACE FOR
FUTURE REFERENCE.
Recheck all screws and bolts to be sure they are
fastened securely. Do not overtighten.
Before using your cot, please read all cautionary
statements on the insert sheet.
Toddler bed rail (UB0399) is not included, sold separately.
Please contact your retailer to purchase.
HFinished assembly

18

19

Made in Vietnam