uBabycare UBC-001 series User manual

UBC-001 UBabyCare User Manual
SMART BABY MAT
www.huijia-tech.com / www.ubabycare.com
USER MANUAL
UBC
-
001
Series
Intelligent Baby Movement Monitor

UBC-001 UBabyCare User Manual
WARNING
IM ORTANT INFORMATION ON USAGE CONDITION
Read the instructions carefully before using your UBC-001 Series Smart Baby Mat (UBC).
UBC has two devices that are Movement Receiver (receiver) and Wireless Movement
Optics Mat (mat). lease put the mat on the bed or mattress, and don’t put it under the
mattress. You can put a sheet or a towel (1cm thickness limit)on top of the mat. For
best sensitivity results, please take note of the following. lace your baby on the mat
such that the chest/back body area lies on the upper or lower part of the mat. Avoid
the mid-point folding area of the mat.
DO NOT break the warranty seal of the Mat packaging ntil yo had tested the
f nctionality of the mat and receiver with a new set of batteries. Breaking the
warranty seal constit tes acceptance of the prod ct in working condition.
QUICK START FUNCTIONAL TEST
1. Insert fresh batteries into the battery compartments of the mat and
Receiver.
2. Power on the mat and receiver.
3. The display sho ld indicate ‘-‘ scrolling in a circ lar fashion to indicate
a calibration process.
Note: Sho ld the display show an error message ‘E1’, ‘E9’ kindly ret rn
the prod ct to the service center for s pport.
Baby weight limit on the mat for effective monitoring should fall within the range
below:
2kg / 4.4lb – 12kg / 26.4lb
lace your baby on the mat such that the chest/back body area lies on the upper or
lower part of the mat. Avoid the mid-point folding area of the mat
Avoid placing any cloth material between the baby and the mat. When cloth
material is placed on the mat, thickness of the material should be less than 1cm.
Recommended materials are bed sheet, bath towel or swaddling cloth. Other
unknown materials may compromise the sensitivity.
-1-

UBC-001 UBabyCare User Manual
NO JUMPING/STAMPING NO SHARP HITS NO HEAVY WEIGHT
NO BENDING OTHER NO HOLDING OF TH E NO IMMERSING IN
THAN THE MID-POINT EDGE IN ONE HAND WATER
-2-

UBC-001 UBabyCare User Manual
• The UBC is NOT a medical device or a diagnostic device to prevent S dden
Infant Death Syndrome (SIDS) or ‘cot death’. Babies with a known predisposition to
any breathing abnormality incl ding apnea sho ld be monitored by a doctor. Please
seek advice from doctors or health care professional for medical diagnosis or
when ns re of any symptoms.
• Yo sho ld not rely on the UBC for the wellbeing of yo r baby. It is NOT a
s bstit te for proper ad lt s pervision. It is important that an ad lt stays within
range of the monitor at all times d ring se.
• Please handle the mat with two hands. DO NOT hold it by the edge with one
hand or bend the mat. Ro gh handling and bending of the mat other than the
mid-point may damage the mat and ca se malf nction.
• It is advisable to se the mat for sleeping p rpose and sho ld not be sed as a
play mat. DO NOT stamp or j mp on the mat as the action may damage the
mat and ca se malf nction.
• Avoid major movement activity aro nd the mat as it is highly sensitive and may
pick p the movement signal as part of the movement signal of the baby.
Patting action, high vibration or motor-r nning activities will affect the
acc racy of the baby movement co nt.
• DO NOT s bject the mat to sharp folds other than the mid-point fold and sharp
objects as it may damage the sensing element and affect the f nctionality
and sensitivity of the mat.
• DO NOT add thick and heavy items s ch as mattress between yo r baby and
the mat as sensitivity of the mat will be compromised. Adhere to the 2kg -
12kg/26lb weight limitation of the mat. It is not meant for ad lt se.
• DO NOT wash or immerse the whole mat in water. Keep yo r mat away from
so rces of moist re. It may ca se the electronic control circ it to malf nction
• Any form of spillage or stain sho ld be wiped off immediately with water on a
damp cloth to prevent permanent stain on the mat. Avoid sing strong
detergent. Gentle wipe is s fficient to clean p stains. Excessive scr bbing
action may damage the water-resistance property of the mat.
• Observe polarity of the battery placement for proper f nctioning of the mat.
• DO NOT disassemble, cr sh, short-circ it or incinerate the battery as it may
ca se fire, inj ry, b rns or other hazards.
• DO NOT p t the Parents Control Unit near wireless devices or a microwave
oven. S ch devices can disr pt the transmission of the alarm signal.
The operating temperat re range for the UBC is from 10
0
C - 40
0
C. DO NOT operate
beyond this range as it may not f nction according to defined specifications.
-3-

UBC-001 UBabyCare User Manual
Receiver Status Indication Summary Sheet – Commonly occurring states
Stat s indication Event Remarks
Calibration in progress
The display will indicate ‘-‘ scrolling in a
circ lar fashion for a period of aro nd
30 seconds
S btle body
movement co nt
The digit change dynamically
depending on the s btle body
movement co nt
Wake p alarm /
Contin o s movement
The display will show ‘M’ blinking
whenever the baby moves. After the
baby falls asleep, movement alert is
activated after a contin o s
movement period of 20 seconds
Absence from mat
The display will show ‘--’ blinking and
alarm will be activated whenever the
baby is o t of the mat
No body movement
detected
The display will show ‘00’ and alarm will
be activated when no body
movement is detected
High body movement
trending p
The display will show alternate blinking
of ‘H’ and c rrent body movement
co nt when high body movement is
trending p. Alarm will also be
activated
Low body movement
trending down
The display will show alternate blinking
of ‘L’ and c rrent body movement
co nt when downward trending of low
body movement is detected. Alarm will
also be activated
High press re exerted /
Weight limit exceeded
The display will show ‘HP’ to indicate
high press re, s ch as heavy weight on
the mat or the baby sitting p. The
alarm will also be activated.
Error 1: Fiber sensor is
broken Please contact yo r service centre
Error 2: Extreme low
battery level of the mat Please replace batteries for the mat
Error 9: Device
Malf nction Please contact yo r service centre
-4-

UBC-001 UBabyCare User Manual
TABLE OF CONTENTS
Warning 1
Disposal instructions 5
Getting Started 5
Specification and Parts description 6
Operation of the UBC 8
Troubleshooting and FAQ 15
Technical Support 16
imited Warranty 17
DIS OSAL INSTRUCTIONS
Do not dispose of this mat and the receiver with nsorted waste. Improper disposal
may be harmf l to the environment and h man health. Please refer to yo r local
waste a thority for information on ret rn and collection systems in yo r area.
GETTING STARTED
Package contents
Yo r UBC-001 package incl des:
• UBC-001-A Movement Receiver(Receiver)
• UBC-001-B Wireless Movement Optics Mat (Mat)
• User Man al
• Carrier bag
Before yo can se the mat, yo need the following
(not incl ded in the prod ct):
• 4 X AA dry cell battery for the mat
• 2 X AAA dry cell battery for the Receiver
-5-

UBC-001 UBabyCare User Manual
S ECIFICATION AND ARTS DESCRI TION
UBC-001-A Receiver
(1) Battery Type:2 x AAA Battery
(2) Size:10.5cm x 5.6cmx 1.6cm
(3) Weight: Abo t 60g (not incl ding the batteries.)
(4) Color: White + Yellow
(5) Material: ABS Plastic+ R bber Keys
1 T rn ON or OFF
Reset alarm (Press and hold the b tton)
2 MODE b tton Toggle between f nctional modes
Reset alarm (press and hold the b tton)
3 SELECT b tton Toggle between selection in the designated mode
Reset alarm (press and hold the b tton)
4 Battery
Compartment To insert 2 x AAA dry cell batteries
5 LCD display Display of baby movement stat s
and f nctional indicators
6 Alarm selector To select vibrate or both so nd and vibrate alarm
7 Clip To clip the Parent Control Unit to the body of a
caretaker
8 Stand To leave the Receiver on a table top or flat s rface
1
2
3
4
5
6
7
8
- -

UBC-001 UBabyCare User Manual
UBC-001-B MAT
(1)Size: 81±2cm x 50 ±1cm x 2.5±0.5cm
(2)Size: Abo t 42cmx 50cm x 3cm
(3)Weight: abo t 1100~1200g (Not incl ding the batteries.)
(4)Color: White + Yellow
(5)Materials: ABS Plastic + Latex + Waterproof cloth
RF arameter
(1) Freq ency: 433MHz, ISM band
(2) O tp t power: 10dBm
9 ON/OFF switch T rn the mat ON or OFF
10 Power LED indicator Mat operation stat s indication
11 Battery compartment
of mat To insert 4 x AA dry cell batteries for the mat
12 B zzer Local a dio alarm o tlet
13 Mat To s pport monitoring of baby
14 Foldable Position Fold the mat locations (other locations do not
fold)
9
10
11
12
13
14
-7-

UBC-001 UBabyCare User Manual
O ERATION OF THE UBC
 2Kg~12Kg Baby is suitable (0~12 months)
1.Insertion of battery on the mat
Flip the mat over to the bottom side. Open p the
battery compartment cover.
Insert the 4 AA batteries.
2.Insertion of battery on the Receiver
Open the battery compartment below the 3
b ttons by sliding the cover downwards as shown
by the arrow label.
Insert the 2 AAA batteries.
3. ower on the Mat
Place yo r baby on the mat.
Press the ON/OFF switch towards the ‘ON’ position.
The LED indicator on the top of the sensor box will
light p alternating between green and red color.
4. ower on Receiver
Press and hold the power b tton till the LCD
display is lighted p.
The receiver will establish connection with the mat
a tomatically. The display will indicate ‘--‘ scrolling
in a circ lar fashion d ring a calibration process of
aro nd 30 seconds as shown.
Once connection is established, the blinking will
cease and the baby stat s will be displayed.
The display will show ‘M’ to indicate baby
movement detected when the baby is moving
-8-

UBC-001 UBabyCare User Manual
5.Mat sensitivity adjustment
To set mat sensitivity, press the MODE b tton ntil
the mat sensitivity symbol is blinking. Adj st
sensitivity by pressing the SELECT b tton. Set
maxim m sensitivity and adj st downwards to
make s re there is no false alarm.
Below is a general g ideline for setting the
sensitivity level.
Modes Age guideline
Weight
guideline
Icon
Display
Sensitivity Level 3
(default)
< 6 months < kg
Sensitivity Level 2 6 – 9 months
– 10 kg
Sensitivity Level 1 9 - 12 month 10 - 12 kg
6. Baby wake up / absence alarm Function etting
The baby wake p / absence alarm enable
f nction allows caregivers/parents to enable /
disable the alarm notification for BOTH the baby
wake p AND absence detection
To set the baby wake p / absence alarm enable
f nction, press the MODE b tton ntil the f nction
symbol is blinking.
Press the SELECT b tton to t rn ON/OFF the baby
wake p / absence alarm enable f nction.
Within the baby wake p / absence alarm enable
f nction is ON. When large movement, the display
with show ‘M’ . When baby is taken o t or not on
the mat, the display with show ‘--’. Both of the
alarm will be activated
Within the baby wake p / absence alarm enable
f nction is OFF, When large movement, the display
with show ‘M’ . When baby is taken o t or not on
MODE SELECT
The baby wake p /
absence alarm
enable f nction
F nction On: display
F nction OFF: No display:
-9-

UBC-001 UBabyCare User Manual
the mat, the display with show ‘--’. B t No alarm will
be activated
BOTH the baby wake p and absence detection is
disabled by defa lt in factory. When disabled, the
baby wake p or absence state will still be
indicated vis ally on the Receiver display.
7. Alarm type selection
Adj st the tone selector switch p or down to
select so nd or both so nd and vibration.
The so nd and vibration f nctions will be displayed
on the LCD.
WARNING:
It is advisable NOT to disable alarm when yo r baby is nwell or need extra attention.
-10-

UBC-001 UBabyCare User Manual
Functions
A. Baby Movement Condition: No sleeping (After calibration process )
.
8.Baby continue movement detect
The display with show ‘M’ when movement is
detected.
9.No body movement
The display with show ‘00’ when no s btle body
movement is detected for consec tive 15
seconds. The alarm will be activated.
Press and hold the MODE, SELECT or POWER
b tton once to de-activate it (normal b tton
f nctions are disabled at this time). Release the
b tton when the alarm is off.
Note: A dio alarm will also be activated on the
mat independent on whether the receiver is
powered on.
10. Baby absence
The display with show ‘--’ when baby is taken o t or
not on the mat.
The alarm will be activated..
Press and hold the MODE or SELECT b tton once to
de-activate it. (normal b tton f nctions are
disabled at this time) Release the b tton when
the alarm is off.
-11-

UBC-001 UBabyCare User Manual
B. Baby Movement Condition: Sleeping
11. Baby movement count
The baby body movement co nt per min te of
the baby is monitored and displayed on the
LCD.
Typical body movement co nt range between
30 and 60.
12.No body movement
The display with show ‘00’ when no body
movement is detected for consec tive 15
seconds. The alarm will be activated.
Press and hold the MODE, SELECT or POWER
b tton once to de-activate it (normal b tton
f nctions are disabled at this time). Release the
b tton when the alarm is off.
Note: A dio alarm will also be activated on the
mat independent on whether the receiver is
powered on.
13. Wake up alarm
The Wake p alarm will be activated only after
the baby is asleep for more than 5 min tes.
The display with show ‘M’ when contin e
movement (eg. awake, crying) is detected.
When a constant baby movement period of 20
seconds is detected, the alarm will be activated
Press and hold the MODE, SELECT or POWER
b tton once to de-activate it (normal b tton
f nctions are disabled at this time).
Release the b tton when the alarm is off. Once
de-activated, there will be a time-o t period of 5
min tes before the alert will be re-enabled.
-12-

UBC-001 UBabyCare User Manual
14. Baby absence
The display with show ‘--’ when the baby has rolled
or carried o t of mat.
The alarm will be activated.
Press and hold the MODE or SELECT b tton once to
de-activate it. (normal b tton f nctions are
disabled at this time) Release the b tton when
the alarm is off.
Note:
15. Upward trend of rapid body movement
alert
In the event of pward trend of rapid body
movement detected, the display will blink,
switching between c rrent body movement co nt
reading and ‘H’ symbol (to indicate high body
movement).
The alarm will be activated.
Press and hold the MODE, SELECT or POWER b tton
once to de-activate it (normal b tton f nctions are
disabled at this time).Release the b tton when the
alarm is off.
Note: the f nction and display will not activated
when the baby is not asleep.
16. downward trending of low body
movement detection
In the event of downward trending of low body
movement detection, the display will blink,
switching between c rrent body movement co nt
reading and ‘L’ symbol (to indicate low body
movement) The alarm will be activated.
Press and hold the MODE, SELECT or POWER b tton
once to de-activate it (normal b tton f nctions are
disabled at this time).Release the b tton when the
alarm is off.
Note: the f nction and display will not activated
when the baby is not asleep.
-13-

UBC-001 UBabyCare User Manual
C. Others
17.Out of range
The open space distance limit between the
Receiver and mat is p to 50 m. Indoor limits will be
red ced significantly, s bject to the layo t of the
b ilding concrete str ct re. The antenna and
monitor alert symbols will blink sim ltaneo sly when
comm nication cannot be maintained between
the Receiver and mat. Walk closer towards the
mat with the Receiver to re-establish the link
Note: Alarm will be also activated on the Receiver
when the mat is NOT powered on.
18. Manual pairing of mat and Receiver
Each mat is a tomatically pre-paired with each of
its Receiver.
Where there is a need to man ally pair the nits,
power off and on the mat again. Power off and on
the Receiver as well. Upon powering on, press and
hold both POWER and MODE b ttons
sim ltaneo sly. Release b ttons when display
shows a ‘P’ symbol alternating between the left-
and right-hand sides.
Pairing process will complete a tomatically and
beep tone will so nd to indicate that the UBC starts
operation.
19.Low battery indication for mat
The low battery indication for the mat will blink
sim ltaneo sly and when battery for the Parent
Control Unit is low.
The a dio alarm will be activated independently
of the switch selection for the alarm type.
Replace battery for the mat.
-14-

UBC-001 UBabyCare User Manual
Warning
There may be exceptional nknown sit ations eg. where babies toss or rotate s ch
that only part of their body lies on the mat, parent’s hands or elbows may press / hit on
the mat or on the cot/mattress where the mat is placed when carrying p the baby -
rendering the c rrent state of the baby to be non-deterministic.
As a preca tion for the nknown states, the display will alternate blinking of o t of mat
“--” and no body movement “00” on the Receiver to alert parents/care-givers to
check on the baby. Please attend to yo r baby
20. Low battery indication for Receiver
The low battery indication for Receiver will blink
sim ltaneo sly when battery for the Receiver is
low.
The a dio alarm will be activated independently
of the switch selection for the alarm type.
Replace battery for the Receiver.
21.Weight limit indication for mat
The weight limit indication for the mat will be shown
as ‘HP’ to indicate high press re, s ch as heavy
weight on the mat or the baby sitting p. The alarm
will also be activated.
Note: If the indication remains when the baby is in
sleeping position, the baby weight had exceeded
the defined weight limit of the mat.
-15-

UBC-001 UBabyCare User Manual
Troubleshooting and FAQ
roblem ossible cause Remedy
False alarm • The baby may have
excessive movement when
the caretaker/sibling is playing
next to the baby or attending
to the baby’s need (changing
diapers, feeding, patting)
• External event s ch as
patting action, high vibration
or motor-r nning activities
near the mat
• Switch off the Receiver
when the parent/caretaker/
sibling is attending to the
baby. Switch it on again to
contin e monitoring when
baby is asleep.
No alarm tone • Battery may be low • Check battery level and
replace battery if needed.
No movement
detected
• The sensitivity level may be
low.
• Adj st p the sensitivity
level with the SELECT b tton
‘M’ (Movement)
display on the
Receiver when
baby is sound
asleep
• Baby may have strong
movement patterns
• Adj st down the
sensitivity level with the SELECT
b tton
Out of range
indication
• The mat and Receiver are
too far apart.
• The mat or Receiver may
be placed near large metal
objects.
• The link between the mat
or Receiver may be lost
• Battery is not inserted on
the mat.
• Try to adj st the relative
distance nearer between the
mat and Receiver.
• Power off and on again
for both the mat and
Receiver to try establishing
the link.
• Enable man al pairing
by powering on 1 mat and 1
Receiver. (refer to Operation
of the UBC Section:
Other of indication)
• Ens re battery is inserted
on the mat side
Wireless link loss • Range too far between
mat and Receiver
• Maintain closer range
between mat and Receiver
• Low battery • Replace batteries
Low battery
indication
• Batteries on the mat or
Receiver may be low or fa lty.
• Replace batteries
E1 • The fiber sensor is broken • Mat is no longer
f nctioning. Please contact
yo r service center.
E2 • Extreme low battery level
of the mat
• Replace batteries for the
mat
E9 • Device Malf nction • Please contact yo r
service center
-1 -

UBC-001 UBabyCare User Manual
TECHNICAL SU ORT
Before yo contact the Technical s pport, please read the Tro bleshooting and FAQ
section.
If yo have q estions abo t the se or feat res of the player please contact o r Call
Center at the following e-mail address:s pport@h ijia-tech.com or contact
UBabycare agent yo b ying it from.
When yo call or contact s for s pport, please incl de as m ch information possible
from the packaging material. This will help s in speeding the process.
MAINTENANC
• DO NOT s bject the mat to sharp folds other than the mid-point fold as it may
damage the sensing element and affect the f nctionality and sensitivity of the
mat. WARRANTY WILL BE VOID ONCE THE MAT IS FOLDED AT ANY PART OF THE
MAT OTHER THAN THE DESIGNATED MID-POINT FOLD.
• DO NOT wash or immerse the whole mat in water. Clean the mat with a soft
damp cloth and allow to dry
• Keep yo r mat away from so rces of moist re. It may ca se the electronic
control circ it to malf nction.
• DO NOT drop the Receiver on the floor as it may damage internal components
and ca se malf nction.
• Keep the Receiver away from moist re.
• Remove batteries from the Receiver and mat when not in se for a long period of
time.
• The operating temperat re range for the UBC is from 10
0
C - 40
0
C.
DO NOT operate beyond this range as it may not f nction according to defined
specifications.
-17-

UBC-001 UBabyCare User Manual
LIMITED WARRANTY
Yo r UBC is covered warranty for malf nction in the electronic parts only, for a period
of 12 months from the date of the original p rchase, when sed in accordance with
the instr ctions provided with the nit. The mat material is a disposable item which is
s bject to wear and tear, will not be covered in the warranty.
We will, at o r discretion, repair or replace the prod ct free of charge, sho ld it fails to
f nction properly when sed as directed within the warranty period.
This warranty does not cover the battery, damaged as a res lt of accidents, improper
maintenance or any other form of mis se. The warranty is also void if the owner
attempts to fold the mat when instr cted not to as stated in the ser man al, repairs or
modifies the prod ct in any way. We are not liable for any incidental or conseq ential
damages with regard to this prod ct. The warranty also excl des any liability other
than what is stated above.
Yo r UBC operates on freq ency of 433Hz and complies with EN and Part 15 of the
FCC r les.
For any technical assistance contact the technical s pport center ：