Ubiquiti airMAX Omni AMO-5G13 User manual

5 GHz 2x2 MIMO
Dual Polarity Omni Antenna
Model: AMO-5G13

Specifications
AMO-5G13
Dimensions 799 x 90 x 65 mm
(31.46 x 3.54 x 2.56")
Weight with Mount 0.82 kg (1.81 lb)
Frequency 5.45 - 5.85 GHz
Gain 13 dBi
Elevation Beamwidth 7°
Electrical Downtilt 2°
Max. VSWR 1.5:1
Wind Survivability 200 km/h (125 mph)
Wind Loading 84.52 N @ 200 km/h
(19 lbf @ 125 mph)
Polarization Dual Linear
Cross-Pol Isolation 25 dB Min.
RF Connectors 2 RP-SMA Connectors (Weatherproof)
Mounting Universal Pole Mount, RocketM Bracket,
and Weatherproof RF Jumpers Included
ETSI Specication EN 302 326 DN2

Introduction
Thank you for purchasing the Ubiquiti Networks® airMAX®
5GHz 2x2 MIMO Dual Polarity Omni Antenna. This Quick
Start Guide is designed to guide you through the installation
of the antenna. This Quick Start Guide also includes the
warranty terms and is for use with the airMAX Omni Antenna,
modelAMO-5G13.
Package Contents
Antenna Pole Clamps
(Qty. 2)
Carriage Bolts
(M8x100, Qty. 4)
5GHz 2x2 MIMO
DualPolarity Omni Antenna
Model:AMO-5G13
Serrated Flange Nuts
(M8, Qty. 4)
RF Cables
(Qty. 2)
Quick Start Guide
Products may be different from pictures and are subject to change without notice.
TERMS OF USE: Ubiquiti radio devices must be professionally installed. Shielded Ethernet
cable and earth grounding must be used as conditions of product warranty. TOUGHCable™
is designed for outdoor installations. It is the customer’s responsibility to follow local country
regulations, including operation within legal frequency channels, output power, and Dynamic
Frequency Selection (DFS) requirements.

Installation Requirements
• Rocket™M5 or RocketM5 GPS (sold separately)
• 13 mm wrench
• Shielded Category 5 (or above) cabling should be used for
all wired Ethernet connections and should be grounded
through the AC ground of the PoE.
We recommend that you protect your networks from the
most brutal environments and devastating ESD attacks
with industrial-grade shielded Ethernet cable from Ubiquiti
Networks. For more details, visit www.ubnt.com/toughcable
Hardware Installation
1. Attach the RF Cables to the connectors labeled Chain 0 and
Chain 1 on the Rocket.

2. Align the mounting tabs on the back of the Rocket with
the Rocket mount, and slide the Rocket down to lock it
into place.
3. Attach the other ends of the RF Cables to the RF connectors
on the antenna.
*640-00047-03*
640-00047-03

4. Insert the four Carriage Bolts into the main mounting
bracket of the antenna.

5. Attach the antenna to the top of the pole. (If the antenna is
attached to a lower point on the pole, part of the signal will
be blocked by the pole.)
Note: The mounting assembly can accommodate a
Ø 38 - 76 mm (1.5 - 3.0") pole.
a. Slide a Pole Clamp over each pair of CarriageBolts.
b. Secure each Pole Clamp with two Serrated FlangeNuts.
c. Tighten all nuts to approximately 25N-m(18lb-ft).

www.ubnt.com
©2012-2014 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, UbiquitiNetworks,
the Ubiquiti U logo, the Ubiquiti beam logo, airMAX, Rocket, and TOUGHCable are
trademarks or registered trademarks of UbiquitiNetworks,Inc. in the United States
and in other countries. All other trademarks are the property of their respective
owners. PH092614