UC Logic Artisul D13 User manual

Artisul D13 Driver Version 1.0
1
User Manual for Windows
Windows 7 / 8 / 8.1
Driver Version 1.X
Version：Ver.2.1
Release Date：2015/11

Artisul D13 Driver Version 1.0
2
Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in
United States and/or other countries.
Any additional company and product name mentioned in this documentation may be registered
trademarks or trademarks.
ARTISUL and UC-Logic are registered trademarks of UC-Logic Technology Corp.
UC-Logic reserves the right to revise this publication without obligation to provide notification of such
changes.
Copyright © 2015 UC-Logic Technology Corp. All rights reserved.

Artisul D13 Driver Version 1.0
3
Contents
I. General Information..........................................................................4
OVERVIEW ..................................................................................4
ARTISUL FUNCTIONS ...................................................................4
SYSTEM REQUIREMENTS .............................................................4
VERIFYING HARDWARE ...............................................................5
USAGE TIPS ...............................................................................10
MAPPING TO MULTIPLE MONITORS...........................................10
II. ARTISUL configuration.....................................................................11
Info...........................................................................................11
Hot Keys ...................................................................................13
Pen Setting................................................................................15
Calibration ................................................................................17
Monitor Tuner...........................................................................19
III. Changing the Pen Tip ......................................................................22
IV. Question & Answer .........................................................................23
V. The right setting of graphic applications ..........................................33
VI. How to care for your ARTISUL..........................................................35
Appendix 1: Troubles and Solutions...................................................... 36
Appendix 2: Uninstall ARTISUL Driver.................................................... 37
Appendix 3: Hot Key comparison table .................................................38

Artisul D13 Driver Version 1.0
4
I. General Information
OVERVIEW
Welcome to the world of ARTISUL! You’ll be able to discover how easy it is to control your personal
computer by using an U Pen instead of a mouse.
The function of the U Pen is able to draw a line very thin, thick, light or dark (also known as
“pressure sensitivity”). You also can write, sign, annotate documents, and draw, sketch or paint as
easily as you would on normal paper and simulate the functions like pencil, mark pen, brush, or
watercolor pen by using graphics software such as Adobe® Photoshop™, Corel® Painter™ and Clip
Studio Paint™.
ARTISUL FUNCTIONS
After installing the device driver, your ARTISUL features have the following functions:
Direct pointing –You can move the cursor to any location by hovering the digital pen tip over
your ARTISUL screen.
Three-button mouse commands - Your ARTISUL provides all the functions of a three button
mouse by using its pen tip and two buttons.
Scroll Diai –You can scroll documents and Web pages by pressing the middle button of the
Scroll Diai over your ARTISUL screen.
Pressure sensitivity –This feature allows you to emulate various brushes and pencils so when
you press down the pen tip with different pressure , you create pencil lines from very thin to
thick.
→Note：The U Pen has a sensitive electronic components inside, which can be damaged when
dropped. Please remember to store it in the pen case or pen stand when it is not in use.
SYSTEM REQUIREMENTS
Windows 7 / 8 / 8.1; USB port and HDMI port; Internet connection.

Artisul D13 Driver Version 1.0
5
VERIFYING HARDWARE
Your ARTISUL and package contents are shown below. If anything is missing, contact your dealer
immediately.

Artisul D13 Driver Version 1.0
6

Artisul D13 Driver Version 1.0
7
INSTALLATION
HARDWARE INSTALLATION
There are two ways to install your hardware:
1. Connect your ARTISUL with a HDMI & USB interface into the computer
2. Using external power adapter
Note: Use only power adapter and cables approved by UC-LOGIC for use with ARTISUL.

Artisul D13 Driver Version 1.0
8
INSTALLING ARTISUL DRIVER ON WINDOWS
1. Please download the driver from WWW.ARTISUL.COM “Support”page.
2. Decompress the driver file and run SETUP.EXE .
3. When installing the driver, follow the installation instructions on your screen and press the
“OK” key.
4. After the installation has completed, you need to reboot the computer.
→Caution:
1. Please remove any existing tablet drivers before installing the ARTISUL driver. ( This
includes the pen tablet driver from any other manufacturer)
This is to ensure your drivers performance will not be effected.
2. Please disconnect your internet before install driver.
3. Please run setup as administrator.

Artisul D13 Driver Version 1.0
9
After you have finished the driver installation and restarted the Windows system. If the device has
been successfully installed, you will see a small ARTISUL icon ( ) appear in the system tray, which
is normally at the lower right corner of the screen.
→Note: Please connected your ARTISUL to your computer before open your creative software.

Artisul D13 Driver Version 1.0
10
USAGE TIPS
1. Double tapping
When you double tap with the digital pen (equivalent to a double click with a mouse), try to
quickly lift the pen tip higher up away from the ARTISUL screen before returning for the second
tap.
2. Scrolling function of digital pen
The Ul pen has the same function as a normal mouse for scrolling pages. Just press the first
button of the digital pen (same function as the mouse middle button) over the ARTISUL
screen.
3. Using U pen without an ordinary mouse
You may install the ARTISUL and a mouse in your computer at the same time. However, only
one device is able to work at a time. You cannot use the mouse and U Pen at the same time.
MAPPING TO MULTIPLE MONITORS
If your computer is equipped with more than one monitor, your ARTISUL will map to the monitors
based upon how they are configured in the DISPLAY PROPERTIES control panel.
After you have correctly configured your computer for using it with multiple monitors, you can then
adjust your ARTISUL mapping by opening the ARTISUL panel and changing the appropriate options.
This enables you to toggle the current ARTISUL mapping and screen cursor between the system
desktop or primary display and your other monitors.
Refer to "Calbration" page 18.
Switching to Full screen mode with U Pen by pressing on the 2nd button of the stylus for 2 seconds .
If you press on the same button for 2 seconds again the screen will revert back to normal.
→Note: 1 . Under "extended display" view, you may use your pen cursor to navigate through both
ARTISUL and monitor display easily by pressing down on the top button of the pen for 2 seconds.
Vice versa, by pressing down the same button for another 2 seconds, your pen cursor will switch
back to navigating on only one display (this could be ARTISUL or your monitor depending on your
original display setting).
→Note: 2 .Under the “Duplicate”display mode of the “Multiple Display” function, the display
resolution of your monitor must be set to the same resolution as your ARTISUL. Otherwise, your pen
cursor will be misplaced on the screen. For ARTISUL D13, please make sure the other monitor
resolution is set to 1920 x 1080.

Artisul D13 Driver Version 1.0
11
II. ARTISUL configuration
You may configure the ARTISUL by modifying the functions of the pen tip and the two barrel
buttons, tap [Start] > [Settings] > [Control Panel], and double-tap the ARTISUL icon ( ), or tap on
the ARTISUL icon ( ) in the system tray, usually located at lower right hand corner of the screen.
Info
The Info tab displays the version number of the driver and Digital Ink function.
1. Support Digital Ink
Select to support the pressure of digital ink settings.
2. Left Hand / Right Hand
Select to left-handed or right-handed users at any time.

Artisul D13 Driver Version 1.0
12
3. Display Rotation
Open “Screen resolution”of Windows . You can modify screen settings such as Resolution,
Orientation and others.(For details, study the documentation that came with your system)
You can rotate the display and cursor of your ARTISUL.
Please follow these steps:
1. Right click your mouse on desktop and select “Screen resolution”
2. Select "Artisul D13" as your Display.
3. You may choose to rotate your ARTISUL screen under "Orientation."
→After the ARTISUL driver has been installed in your Windows; if the "Supports Digital Ink"
function is selected, your ARTISUL will support pen pressure in MS Journal, OneNote (2003, 2007),
etc.
→ If the "Supports Digital Ink" function is disabled, most of the art software pen’s pressure
(Photoshop, Illustrator, Corel Painter) is still working, but pen pressure will not be available when
using MS Journal, OneNote (2003, 2007) , etc.
2
3

Artisul D13 Driver Version 1.0
13
Hot Keys
For Hot Keys , Scroll Dial and Pen button settings, you can modify these using the Hot Keys
configuration page. You can use the Hot Keys to perform frequently used functions or keystrokes.
Redefine Hot keys
Just click the button and choose from any of the available functions.
→Note : Software keystrokes are based on English input methods. Please make sure your input
method is set to English when using Hot Keys on your ARTISUL.
→Note : Most creative software will not accept keystroke input when your U pen is still in use
or when your U pen tip is still within the detectable cursor range. To avoid invalid keystroke
actions, please allow the pen to cursor to leave the screen of ARTISUL D13 before pressing your
Hot Keys. (To leave the screen, allow your U pen tip to be at least 1.5" away from the surface of
the D13 screen.)

Artisul D13 Driver Version 1.0
14
Default
Return the Hot Keys setting to factory default.

Artisul D13 Driver Version 1.0
15
Pen Setting
You can adjust “Double Click Time”and “Pressure Setting”in this tab.
Double Click Time:
Move the Speed Slider toward “Slow” if you want more time in double tapping with Pen Tip or
less time if you move the Speed Slider toward “Fast”. This setting is the same as Double-click
Speed on the page displayed by selecting Start ►Control Panel ►Mouse ►Buttons.
Changing the speed in one section is the same as changing the speed in the other tab.
Pressure Test:
There are four different colors for selecting the pressure sensitivity of the ARTISUL, and they
can be adjusted in this tab. There is a test area to see the thickness of a line by pressing down
on the pen tip to the pad. The numerical value of the pressure level is shown in the field above
the “Clear” button.

Artisul D13 Driver Version 1.0
16
Clear
Tap on the “Clear” button to clean the space up in the Pressure Test area.
Pressure Setting
By default setting, tapping with the pen tip is equivalent to a left click of a mouse. Move the
slider in the sensitivity bar to adjust the pressure response of the pen tip. Light means your
ARTISUL Tablet will recognize the slightest nuance of pressure while heavy will take more
pressure before the digital ink or pen click will be recognized. The pressure test is also there for
you to test out the differences between light and heavy pen pressure settings. We recommend
for you to take some time to set up your own preferred pen settings.
Note: Please close ARTISUL D13 control panel when you are finished with the Pressure Test .

Artisul D13 Driver Version 1.0
17
Calibration
Monitor:
If you have chosen to use the "Extend these displays" mode under the "Multiple Display"
function, please use the ARTISUL "Monitor" section to select your corresponding screen to
navigate your ARTISUL Upen.
.

Artisul D13 Driver Version 1.0
18
Calibration U Pen:
If you want to compensate for viewing angle. You can calibrate ARTISUL.
1. Press “Calibration U Pen”to activate the calibration screen.
2. Hold the pen perpendicular to the calibration screen and use the pen tip to click on the
center of the crosshairs in the calibration dialogue.
3. Click “OK” to end the calibration.
Open Monitor Tuner:
Monitor Tuner can help you configure the ARTISUL monitor Brightness、Contrast and Color
Temperatures. Press "Open Monitor Tuner" button to open "ARTISUL Monitor Tuner" utility.
.
→Note：When opening ARTISUL Monitor Tuner, the system will need up to 30 seconds or more to
access the necessary information of your monitor. Please note that while the system is calling up the
"ARTISUL Monitor Tuner," it is possible for the screen to flicker once or twice.

Artisul D13 Driver Version 1.0
19
Monitor Tuner
Calibrated Display Options
These options are there to assist you with preparing your designs for CMYK printing. You may
choose a different calibrated display setting depending on the type of paper you will be
printing your work and the working light environment (this includes sunlight or the color
temperature of your office light tubes etc.).
User setting
Select User Setting you can configure the ARTISUL monitor Brightness、Contrast and Color
Temperatures.

Artisul D13 Driver Version 1.0
20
Color Temperatures
You can select the default color temperature settings or the “User 1”to adjusts the red,
green and blue color values..
Brightness
You can adjust the brightness of your ARTISUL screen by selecting “Increase” or “Decrease”.
Contrast
You can adjust the contrast of your ARTISUL screen by selecting “Increase” or “Decrease”.
Note: The "Calibrated Pen Displays" are only there to assist you, to prepare your work for best
accuracy before CMYK Printing, refer to guidelines set by your printing services.