Uconnect RS-232 User manual

BLE V5.0 RS-232 adapter user manual V1.6 2020.08.14
1
Bluetooth V5.0 BLE RS-232 Serial Adapter
Model: S2B5232I (Internal Antenna)
1. Package content:
BLE V5.0 RS-232 adapter
White Box: 11 x 6 x 5 (cm)
Total Package Weight: 100 g
Package Contents:
BLE V5.0 RS-232 adapter x 1
A4 User manual x 1
Mini USB Cable x 1
2. Profile:
2.1 Top view:
LED Status Description
Data LED flash Data transmission
Data LED solid on No data transmission
Link LED solid on BLE Link
Link LED flash No Link
Data & Link LED solid on DFU/OTA Mode
DB9 (Male)
Mini USB (Power)
▲
▲▲
▲
+
(5~40 VDC)
▼GND
Reset to Default
LED:
Link: Blue
PWR/Data: Red
Antenna Inside
(Keep clear area)

BLE V5.0 RS-232 adapter user manual V1.6 2020.08.14
2
2.2 Rear Side:
Switch configuration:
Setup CTS/RTS Unused Parity Role Baud Rate
9 8 7-6 5 4 3-2-1
0: by APP or
Command
1: by Switch
0: Disable
1: Enable
0: None
1: Even
0: Peripheral
1: Central
(Auto link with
peripheral)
110:2400
111:4800
000:9600
001:19200
010:38400
011:57600
100:115200
101:230400
Remark:
1. “000000000” by default, in red bold character
2. The GATT service and AT command will support more settings than the DIP switch, please
check the page 4 section 5 and page 5 section 6.
2.3 DB9 connector (Male)
DIP Switch
▲DCE
▼DTE
2: RX 7: RTS
3: TX 8: CTS
5: GND 9: VCC

BLE V5.0 RS-232 adapter user manual V1.6 2020.08.14
3
Pin Signal DTE Direction DCE Direction Description
1 N/A
2 RxD Output Input Transmitted data
3 TxD Input Output Received data
4 N/A
5 GND Ground
6 N/A
7 RTS Input Output Clear to send
8 CTS Output Input Request to send (Default)
9 VCC Power Input (5~40 VDC)
3. Power supply:
3.1 Voltage: 5~40 VDC, Don’t exceed the limit.
3.2 There’re 3 ways to power the adapter: Mini USB, 2P Terminal Block (Blue) and pin9 of DB9,
please choose one. Don’t power the adapter by more than one source.
3.3 The mini USB to type A cable is inside the standard package.
4. Specifications:
4.1 Default value:
Baud rate: 9,600 bps
Data bit: 8
Parity: none
Stop bit: 1
Flow control: none
Device Name: BLE232
Pin code: None, Fast pairing
4.2 Serial Port:
Baud Rate: 1.2/2.4/4.8/9.6/19.2/38.4/57.6/115.2/230.4 Kbps
Parity: none/even, w/o Odd
Stop bit: 1 (Only)
Data bit: 8 (Only)
Remark: The GATT service and AT command will support all the functions, please check the
page 4 section 5 and page 5 section 6.
4.3 Range: max. 50 m in open space (The range depends on the real environment.)
4.4 TX Power: Max. 4 dBm
4.5 RX Sensitivity: -96 dBm typical
4.6 TX current consumption of 16.6 mA (radio only, 4 dbm)
4.7 Operation Temperature: –40 °C to +85 °C
4.8 Dimensions: 87 mm (L) x 34 mm (W) x 18 mm (H)
4.9 Antenna Gain: max. 2 dB (Default)
Remark: All contents are subject to change without notice.

BLE V5.0 RS-232 adapter user manual V1.6 2020.08.14
4
5. GATT Service:
5.1 Architecture:
5.2 UUID_1800_SERV = ("00001800-0000-1000-8000-00805F9B 4FB")
UUID = 2A00, Device name, Default: BLE2 2
5. UUID_180A_SERV = ("0000180A-0000-1000-8000-00805F9B 4FB")
UUID= 2A26, Firmware version, Format: x.x.x, ASCII/read only
UUID= 2A24, BLE version, Format: x.x, ASCII/read only, Value: 4.2 or 5.0
5.4 UUID_BLE_SERV = ("000 ABCD-0000-1000-8000-00805F9B01 1") (Self defined UUID)
UUID_BLE5DATA = ("000 1201-0000-1000-8000-00805f9b01 0"), Data from
BLE2 2_TxData (Notification)
UUID_BLE5SENT = ("000 1202-0000-1000-8000-00805f9b01 0"),//Data to
BLE2 2_RxData max244bytes/package(write only)
UUID_BLE5CONF = ("000 120 -0000-1000-8000-00805f9b01 0"), Configuration, 4bytes,
(read/write)
Devi e Information
Firmware Revision String
TxData
RxData
BLE_CONF
Ma ID
Devi eName
PinID_Setting
Serial BLE Servi e
SetChara teristi Notifi ation(Char)
SetChara teristi Notifi ation (Char)
SetChara teristi Notifi ation(Char)
writeChara teristi (Char)
writeChara teristi (Char)
writeChara teristi (Char)
writeChara teristi (Char)
writeChara teristi (Char)
Mobile APP
SERIAL

BLE V5.0 RS-232 adapter user manual V1.6 2020.08.14
5
UUID_BLE_Config (4 bytes): 00031203-0000-1000-8000-00805F9B0130
Byte0 (Read Only) Byte1 Byte2 Byte3
Product model Baud Rate N/A Port setting
0xAA: RS232
0xAF: RS485/422
0x00: 1200 bps
0x01: 2400 bps
0x02: 4800 bps
0x03: 9600 bps
0x04: 19200 bps
0x05: 38400 bps
0x06: 57600 bps
0x07: 115200 bps
0x08: 230400 bps
bit 0: Parity (0: NONE 1: EVEN)
bit 1: Flow control (0: Disabled 1:
Enabled) (for RS232 model Only)
bit 2: N/A
bit 3: Port Type (0: RS485 1: RS422)
(Available on RS485 model only)
bit 4: BLE Role (0: Peripheral 1:
Central) (indication Only)
bit 5: ControlSet (0: set by APP or
command 1: set by 9P switch)
(indication Only)
UUID_BLE5ADDR = ("00031204-0000-1000-8000-00805f9b0130"), Target Peripheral Mac.
Address, 6bytes,(read/write)
UUID_BLE5NAME = ("00031205-0000-1000-8000-00805f9b0130"), Device name, Max.
15bytes, UTF-8,(read/write)
UUID_BLE5PIN = ("00031206-0000-1000-8000-00805f9b0130"), Pin code, 6bytes,
(read/write)
UUID_BLE5RBT = ("00031210-0000-1000-8000-00805f9b01 0");Reboot, 2bytes,
(read/write)
6. Command set via COM port:
Command
Value
Description
AT Check the connection status between control terminal and the RS-232
adapter. Response: “OK” when the connection is ok. Response:
“ERROR” when the connection is not ok.
BAUD= This command is used to specify the baud rate of COM port.
The command will need 200 ms delay.
1200 1200 bps
2400 2400 bps
4800 4800 bps
9600 9600 bps
(Default) 19200 19200 bps
38400 38400 bps
57600 57600 bps
115200 115200 bps
230400 230400 bps
? Inquire the current baud rate.
DEFAULT= This command will restore the default settings.
Y Restore the default settings (e.g. 19200 bps).
The command will re-start the system for 1 second.

BLE V5.0 RS-232 adapter user manual V1.6 2020.08.14
6
DFU= Device Firmware Upgrade via PC software. OTA (Over the air) is
available to upgrade the firmware by APP
Y
ECHO= This command is used to specify whether the adaptor echoes
characters received from the UART back to the DTE/DCE.
N Command characters received from the UART are not echoed back to
the DTE/DCE.
(Default) Y Command characters received from the UART are echoed back to the
DTE/DCE.
? Inquire the current setting.
FLOW= This command enable or disable flow control signals (CTS/RTS) of the
UART port. Note, the setting is not affected by DEFAULT.
The command will need 1 second delay.
(Default) N Disable flow control.
Y Enable flow control.
? Inquire the current setting
NAME= This command is used to specify a device name for the adaptor.
You can specify a friendly name using 0 to 9, A to Z, a to z, space and
–, which are all valid characters. Note that “first space or -, last space or
– isn’t permitted”. The default name is “Serial Adaptor”.
(Default) BLE232 Default device name
xx….xx “xx….xx” is a character string with the length from 2 to 30.
R Restore the default settings name=“BLE Serial”.
? Inquire the name of the local adaptor.
PARITY= This command is used to specify parity bit setting of COM port.
The command will need 200 ms delay.
(Default) N None parity bit
E Even parity
? Inquire the current setting.
PIN= This command is used to specify a PIN code. The default is simple
paiing w/o PIN code. The format is 6 number only.
000000 Disable the PIN authentication and fast pairing
xx….xx “xx….xx” is a 0~9 number
? Inquire the current PIN.
PROMPT=
The command is used to decide whether result messages are prompted
when Setup commands are executed. The result messages are:
OK/ERROR for command execution.
(Default) Y Prompt result messages.
N Not prompt result messages.
? Inquire the current setting.
ROLE= This command is used to specify whether the adaptor is in the central
or peripheral role. If the device role is changed, the adaptor will reboot
and all paired addresses will be cleared.
C Set the adaptor to the central role.
(Default) P Set the adaptor to the peripheral role.
? Inquire the current role of the adaptor.
STATUS= Inquire all the current setting of the adapter.

BLE V5.0 RS-232 adapter user manual V1.6 2020.08.14
7
? Display the current setting of the adapter
VERSION= This command is used to inquiry the firmware version.
? Inquire the version codes.
7. Central and Peripheral: (Similar like the traditional Bluetooth Master and Slave roles)
7.1 DIP switch setting: The central will pair the slave automatically, please refer to page 2
section 2.3.
Switch DIP-9 to 1 (Configuration by DIP Switch)
Switch DIP-4 to 1 (Central)
The central will link with the neighboring peripheral automatically. The blue LED will be
solid on. The central will link with the paired peripheral on next time when power on.
Please reset to the default and follow the above procedures if you want to link with
other same BLE serial adapter.
7.2 AT command: Please refer to page 5 section 6. The DIP-9 on the default setting (0).
Set “role=c” or “ROLE=C” in one adapter.
The central will link with the neighboring peripheral automatically. The blue LED will be
solid on. The central will link with the paired peripheral on next time when power on.
Please reset to the default and follow the above procedures if you want to link with
other BLE devices.
7.3 APP setup: Please contact the supplier to for the test APP.
The APP will search the BLE and select one as the central.
Then select the other one as the peripheral and link.
The central will link with the neighboring peripheral automatically. The blue LED will be
solid on. The central will link with the paired peripheral on next time when power on.
Please reset to the default and follow the above procedures if you want to link with
other BLE devices.
8. APP: The APP is used for the configuration and the data transmission test.
Device list
Select one

BLE V5.0 RS-232 adapter user manual V1.6 2020.08.14
8
Download: Please contact the supplier for the APP download or the sample code.
Android: iOS:
Send data
Receive data