UE Systems Ultraprobe 3000 User manual

1
UE SYSTEMS INC.
THE ULTRAPROBE 3000 MANUAL

2
TABLE OF CONTENTS
OVERVIEW
COMPONENTS
ACCESSORIES
OPERATION MODE
Introduction
Operation Mode
Setup Mode
Basic components of your kit
Plug-In Modules
Scanning Module
Stethoscope Contact Module
Pistol Grip Housing
Display Panel
Sensitivity Control Dial
Headphone Jack
USB Port
Trigger On/Off Switch
Battery Compartment/Battery
Wrist Strap
Standard Accessories
Headset
WTG-1 Warble Tone Generator
Rubber Focusing Probe
Stethoscope Extension Kit
Optional Accessories
LRM
Display Panel
Bar Graph Display
4
4
4
4
5
5
5
5
6
6
6
6
6
7
7
7
7
8
8
8
8
9
9
9
10
10

3
SETUP MODE
USER INSTRUCTIONS
Sensitivity Control Dial
Sensitivity Adjust
Frequency Adjust
Store a Reading
Overwrite Data or Enter Data in a New Location
To Download the Information
Send Records
Delete Records
Adjust Shut Down Time
User Sensitivity Defaults
Store Mode
Program Update
Exit
Scanning Module
Method of Airborne Detection
Headphones
Rubber Focusing Probe
Stethoscope Module
Stethoscope Extension Kit
Long Range Module
Charging the UP3000
Warble Tone Generator WTG-1
Charging the WTG-1
Case Lock Combination
Specifications
Support/Contact
10-11
11
11
11-12
12
12
13
13
14
14
15
16
16
17
17
17
17
17
18
18
18
19
19
19
20
21
21

4
Congratulations, your digital Ultraprobe 3000 is full of highly advanced technical
features that will provide you with the ability to locate leaks, detect faulty steam
traps, test bearings, store and download your test data.
OVERVIEW
INTRODUCTION
The Ultraprobe 3000 is a versatile instrument with many features that will make your inspections easy,
fast and accurate. As with any new instrument, it is important to review this manual before you begin
inspections.
THERE ARE TWO MODES THAT ARE IMPORTANT TO UNDERSTAND:
OPERATION MODE:
The operation mode will be described in detail under the operation mode section. In this mode, you will
perform all inspection actions such as scanning, probing, “Click and Spin” activities, and store data.
NOTE: “Click” operations require pressing the dial. “Spin” operations require turning a dial.
SET UP MODE:
The setup mode will be described in detail under the Set Up Mode section. There are seven menu
options that will be described in that section.

5
PLUG-IN MODULES
SCANNING MODULE. This module is utilized to receive air
borne ultrasound such as the ultrasounds emitted by
pressure/vacuum leaks and electrical discharges. There one male
plug at the rear of the module. For placement, align the plug with
the corresponding receptacle in the front end of the pistol housing and plug in. The Scanning
Module has a piezoelectric transducer to pick up the airborne ultrasound.
COMPONENTS
BASIC COMPONENTS OF YOUR KIT
0
Charger
s
Pistol Grip Housing
Warble Tone Generator
Long Range
Module (optional)
Rubber Focusing
Probe
Scanning Module
Headphones
Stethoscope Module

6
STETHOSCOPE (CONTACT) MODULE. This is the module with the metal rod.
This rod is utilized as a "waveguide" in that it is sensitive to ultrasound that is
generated internally such as within a pipe, bearing housing or steam trap. Once
stimulated by ultrasound, it transfers the signal to a piezoelectric transducer located
in the module housing directly behind the “wave guide”. For placement align the
plug with the corresponding receptacle in the front end of the pistol housing and
plug in.
PISTOL-GRIP HOUSING
DISPLAY PANEL. In the Operation Mode, the Display Panel will show intensity levels (as dB and
as a bar graph), Sensitivity Level, Storage location number, and Battery Level. Intensity levels are
shown simultaneously as a numeric dB value and on a sixteen-segmented bar graph (with each
segment representing 3 dB). This Ultraprobe receives ultrasound centered around 40 kHz and is
non-adjustable.
SENSITIVITY/STORAGE ENTRY CONTROL DIAL. This is the most important control in
the unit. It is used to adjust the sensitivity. When clicked, it changes functions such as store data
or change the storage location number. It is also used to get into the “SET UP” mode (described
later).
HEADPHONES JACK. This is where you plug in the headphones. Be sure to plug it in firmly
until it clicks.
Display Panel
Headphone Jack
Sensitivity Control/ Storage Entry Dial

7
USB PORT. This port is used to download/transfer information from the Ultraprobe 3000 into the
computer. It is also used to charge the instrument. Before downloading data be sure the cable is
connected to both the USB port and to the computer. When charging, plug the recharger cable
into the USB and then into the electric
receptacle.
TRIGGER ON/OFF SWITCH. The
Ultraprobe is always "off' until the trigger
switch is pressed. To operate, pull in and
hold the trigger. To turn the instrument
off, release the trigger.
BATTERY COMPARTMENT.
The Handle contains the rechargeable
battery. Remove the battery only
when it cannot hold a charge and
needs to be replaced. If the battery is
to be changed, remove the cover and
replace.
The battery is a rechargeable battery and
is charged using the USB port.
WARNING: ONLY USE UE SYSTEMS
BATTERY RECHARGER #BCH-3L.
DO NOT use Unauthorized Batteries or Battery Rechargers! Doing so may be
hazardous and may damage the instrument and will void the warranty.
Recharging the battery takes about 1 hour; continuous run time is about 2 hours. With
normal operation (on-off between tests) the charge will last 4-6 hours. On the BCH-3L
BATTERY RECHARGER, when the light is red the battery is charging and when it is green
it is fully charged.
WRIST STRAP.
To protect the instrument, against unexpected droppage use the wrist strap.

8
ACCESSORIES
STANDARD ACCESSORIES
DHC 2HH. Headphone headset is for use with a hard hat.
This heavy-duty headset is designed to block out intense
sounds often found in industrial environments so that the
user may easily hear the sounds received by the
ULTRAPROBE. In fact, the headphones provide over 23 dB
of noise attenuation.
WTG-1 WARBLE TONE GENERATOR. The WTG 1 Tone Generator is an ultrasonic
transmitter designed to flood an area with
ultrasound. This Tone Generator is a WARBLE
TONE GENERATOR. This internationally patented
transmitter sweeps through a number of ultrasonic
frequencies in a fraction of a second to produce a
strong, recognizable "Warble" signal. The warble
tone prevents a standing wave condition, which
can produce false readings. This is typically used
for Sensitivity Validation.
RUBBER FOCUSING PROBE. The Rubber Focusing
Probe is a narrow rubber shield. It is used to block out
stray ultrasound and to assist in focusing on the field of
reception of the Scanning Module.

9
STETHOSCOPE EXTENSION KIT. This consists of three metal rods that will enable a user to
reach up to 31 additional inches (78.7 cm) with the Stethoscope Probe.
OPTIONAL ACCESSORIES
LONG RANGE MODULE LRM. This uniquely
designed module doubles the detection distance of a
standard scanning module and provides a narrow
(10°) sensing area making it ideally suited for locating
ultrasonic emissions (such as a leak or electrical
emission) at a distance.

10
OPERATION MODE
DISPLAY PANEL
When the trigger is pressed to turn the instrument on, the Display Panel will display the decibel and bar
graph intensity levels. The sensitivity level will be displayed in the upper left corner. The storage
location number will be shown in the upper right corner. The Battery Charge level is shown in the mid-
right side of the display.
BAR GRAPH DISPLAY
The bar graph has 16 segments. At the end of the bar graph is a vertical line, which indicates
the maximum intensity. This is a maximum level hold function. When in operation, the bar
graph will move up and down the scale as an indication of the amplitude of a sensed
ultrasound. The maximum level indicator will remain at the highest sensed intensity during an
inspection until: 1. A new maximum reading is detected, or 2. The trigger is released, and the
instrument is turned off. At which time it will reset.
SENSITIVITY CONTROL/STORAGE ENTRY DIAL
TO ADJUST THE SENSITIVITY
Look at the display and note the “S =” value. If the instrument is within
range, a dB (decibel) value will be displayed.
The maximum sensitivity value is 70; the minimum is 0.
To reduce the sensitivity/volume, rotate the dial counter clockwise. To increase the sensitivity,
rotate the dial clockwise. The Sensitivity control dial increases/decreases the sensitivity of the
instrument simultaneously with the sound level in the headphones.
Storage Location
Battery Level
Sensitivity Level
Bar graph & Maximum
Level Indicator