UI NanoSwitch User manual

NanoSwitch SelfTappingScrew MetalStraps(Qty.2)
PackageContents
InstallationRequirements
Mountingaccessoriesanddrainwirearenotincluded.
PoleMounting
Drillwitha4.5mmDrillBit
7mmSocketWrenchorScrewdriver
WallMounting
(2)Screws(≤5mmScrewHead)
(1)DrainWire,Optional(≤12AWG,≤1m)
Cables
ShieldedCategory5(orabove)cablingwithdrainwireshouldbeusedforall
wiredEthernetconnectionsandshouldbegroundedthroughtheACgroundof
thePoE.
Werecommendthatyouprotectyournetworksfromharmfuloutdoor
environmentsanddestructiveESDeventswithindustrialgrade,shielded
EthernetcablefromUbiquiti.Formoredetails,visit:ui.com/toughcable
Surgeprotectionshouldbeusedforalloutdoorinstallations.Werecommend
thatyouusetwoEthernetSurgeProtectors,modelETHSPG2,onenearthe
NSWandtheotherattheentrypointtothebuilding.TheETHSPG2will
absorbpowersurgesandsafelydischargethemintotheground.
NSWQuickStartGuide

HardwareOverview

PowerLED
PoELED
LinkLED
PoEInPort
GroundBondingPoint
PoEOut(Ports13)
ThePowerLEDwilllightbluewhenthedeviceisconnectedtoapowersource.
Green Active24VPoE
Green
LinkEstablished
FlashingIndicatesActivity
RJ45portsupports10/100/1000Ethernetconnectionsandsupports24V,2pair
passivePoEtopowertheswitch.Formaximumpowerconsumptionof30W,
werecommendsupplyingpowerwiththePOE2430WGWHPoEadapter
(notincluded).
TheNanoSwitchmustbegroundedinoneofthefollowingways:
UsetheSelfTappingScrewtogroundtheNanoSwitchdirectlytoa
groundedmetalpoleorstructure.
UsetheMachineScrewandNuttoattachadrainwire(notincluded)thatis
connectedtoaremotegroundingblockorstructure.
RJ45portssupport10/100/1000Ethernetconnectionsandprovidepassive
24V,2pairPoEpassthroughforupto30WPoEoutput.
WARNING:PoEisalwaysactive.Beforeconnectingadevicetoa

WARNING:PoEisalwaysactive.Beforeconnectingadevicetoa
PoEOutport,ensurethatthedevicesupportspassivePoEandthe
suppliedvoltage.
WARNING:DoNOTprovidemorethanatotalof24WPoEoutput
(24V,1A)perportor30Wtotaloutput;otherwisethiswilldamagethe
NanoSwitch.
ConnectaDrainWire(Optional)
IfadrainwireisusedtogroundtheNanoSwitch,attachittotheGroundBonding
PointwiththeSelfTappingScrewandNut.
Attheinstallationsite,securetheotherendofthedrainwiretoagroundedmast,
pole,tower,orgroundingbar.
HardwareInstallation
Followtheappropriatestepsforyourinstallation:
“PoleMounting”
“WallMounting”
PoleMounting
1.IfyouareusingtheSelfTappingScrewforgrounding,removetheMachine
ScrewandNut:

2.
3.

4.
Note:Ifyouareusingadrainwireforgrounding,proceedto
“ConnectingPower”.
5.

6.
WallMounting
Note:Screwsnotincluded.
1.

1.
2.

3.
4.

5.