ULNA CPE629D User manual

WIRELESS BRIDGE
USER MANUAL
Model: CPE629D
Tips:
Thank you for ordering and using ULNA CPE629D Wireless Bridge, please
read the manual carefully before use. If there are any problems during
the use, please contact us in time.
(Reference connection setup video: You can search for ULNA wireless
bridge on Hardy Brothers Product Reviews channel on YouTube.)
The installation of this device requires some network knowledge. If you
can't install it, please let us know or contact a professional.
Customer Service Email: [email protected]

Contents
1. Overview
1.1 introduce
1.2 Highlights
1.3 specifications
2. PackageIncluded
3. Interface Details
3.1. Button Operation
4. LED Indicator Details
4.1 Details
4.2 Successfully Pairing
5. Quick Start
5.1 PoE Power Supply
5.2 Point to Point Pairing Step
5.3 Point to Multipoint Pairing Step
6. Installation
6.1 Pole mount
6.2 Wall-mounted
6.3 Connect to the device
7. WiFi Function
8. Application Case
9. Advanced Settings
10. Troubleshooting
11. Technical Support and Service
1
1
1
2
3
3
4
4
4
4
5
5
6
7
8
8
8
8
10
11
12
31
32

1、Overview
1.1 Introduce
[email protected] 01
ULNA CPE629D is a dual band long-distance 5.8G&2.4G wireless
transmission device. It uses wireless communication technology to transmit
network data using air as a medium to perform long-distance point-to-
point or point to multi-point interconnection. The working data link layer
realizes the interconnection of local area networks. The transmission
distance can reach up to 5km.
CPE629D Video Bridge Transmission usually consists of two devices in AP
and Client mode respectively. On the Client-side (Receiver) CPE connects
with IP Camera, at the AP side (Transmitter) CPE connects with a video
recorder. The AP can be receiving wireless data transmitted from multiple
Clients, and it is easy and convenient for centralized management of the
remote equipment.
CPE is widely used in highways, reservoir river monitoring, elevator
monitoring systems, site crane monitoring systems, port terminal
monitoring systems, marine aquaculture monitoring systems, and so on.
Point to point extend network WiFi range, extend the network in the house to
your barn, garage, church, warehouse, and even neighbor's house through
wireless bridge signal transmission. No need to install a new modem and
pay for it every month, saving you money.
1.2 Highlights
1. Transmission using dual band 5.8Ghz&2.4Ghz wireless technology；
2. High Speed 1000Mbps RJ45 LAN port, support Gigabit；
3. Built-in 4 x 15dbi high gain WiFi antenna；
4. IEEE802.11ac,IEEE802.11a ,IEEE802.3u,IEEE802.11b/g/n,；
5. Transmission distance up to 5km (Barrier-Free)；
6. Supports WiFi hotspot access；
7. Easy to dial to set the transmitter (Master bridge) and receiver
(Slave bridge) ；

1.3 Specifications
[email protected]
02
8. WDS networking mode, video network dual compatible；
9. Support point-to-point, point to multi-point mode；
10. Support 24V POE power supply, easy to install and deploy；
11. Support WEB GUI access management device.
ULNABrand
CPE629DModel
MT7620A+7612E+JL2101DCPU
8MByteFlash
64MByteDRAM
1000Mbps LAN x 1 & 10/100Mbps LAN x 1
Interface
11b：1/2/5.5/11Mbps
11g：6/9/12/18/24/36/48/54Mbps
11n：Up to 300Mbps
11ac+: Up to 900Mbps
Data rate
IEEE802.11ac, IEEE802.11a, IEEE802.3u, IEEE802.11b/g/nTransfer method
2.4G:2412-2184 MHz 5.8G:5180-5825 MHzFrequency Range
≤3W, POE 24V~1APower
15dBi x 4, Horizontal 60°/Vertical 30°Antenna
SupportWEP GUI
SupportTelnet
SupportSerial
WPA-PSK/WPA2-PSK, WPA/WPA2Safety
-40～75℃Temperature

2. Package Included
3. Interface Details
[email protected] 03
2 x CPE629D Wireless Bridge
2 x Gigabit PoE injector (24V)
2 x Cat 5e Network Cable
2 x Metal Hoop
1 x Mounting Screw Set
1 x User Manual
Power
indicator
Reset Button
LAN1/LAN2
WLAN
Signal
Light
1000Mbps LAN
DC(Unavailable)
Fixed Bracket
Universal Ball
Head
Digital Tube
A-B Button
100Mbps LAN
WIRELESS BRIDGE
USER MANUAL
Model: CPE629D
Tips:
Thank you for ordering and using ULNA CPE629D Wireless Bridge, please
read the manual carefully before use. If there are any problems during
the use, please contact us in time.
(Reference connection setup video: You can search for ULNA wireless
bridge on Hardy Brothers Product Reviews channel on YouTube.)
The installation of this device requires some network knowledge. If you
can't install it, please let us know or contact a professional.
Customer Service Email: [email protected]
PWR LAN1 LAN2 WLAN
Horizontal Ruler

4. LED Indicator Details
[email protected]
04
Press and hold for 5S to reset the wireless bridge; in setup mode, short
press once to toggle a different character to pairing.
Pushing the button to "A" indicates that the bridge acts as the master
bridge (transmitter), and pushing the button to "B" indicates that the bridge
acts as the slave bridge (receiver).
3.1. Button Operation
4.1 Details
4.2 Successfully Pairing
Reset Button :
A-B Button :
Master bridge
Slave bridge
PWR LAN1 LAN2 WLAN
Power indicator
LAN1/LAN2
WLAN Signal Light
Transmitter A Mode Receiver B Mode
0 1 2 F
PWR LAN1 LAN2 WLAN PWR LAN1 LAN2 WLAN

5. Quick Start
[email protected] 05
The CPE629D wireless bridge adopts a PoE power supply, which is easy to
install and manage while saving costs.
5.1 PoE Power Supply
DescriptionLED Light
Power indicator, the LED is on after the power is
connected.
PWR
Digital display LED display "H" indicates manual
configuration status.
Digital Tube
Digital display LED display "L" and flashing
indicates settings status.
Digital Tube
Digital display LED flashing indicates edit the
config or connecting
Digital Tube
Display that a fixed number is solid, it means that
the two bridges are paired successfully and are
working.
Digital Tube
When the bridge is connected successfully, the
WLAN light will be on, Otherwise, the WLAN light
will not bright.
Signal Lights
The data connection is successful, the LED light is
on. Otherwise, it is not bright.
LAN1/LAN2

[email protected]
06
1.2 You can also connect the PoE port of the PoE injector to the 1000Mbps
LAN Port of wireless bridge, LAN port of PoE to the the PC, router, and switch.....
1.1.1. According to the requirements, prepare a long enough network cable
(Recommended within 20 meters, must Cat 5e or up）to connect the
wireless bridge and the PoE injector. The PoE port of the PoE injector is
connected to the 100Mbps LAN port of the wireless bridge.
1.1.2. The 1000Mbps LAN port of the Wireless bridge is connected to the PC,
router, and switch...
5.2 Point to Point Pairing Step:
1. Switch one unit to A(Master Bridge) and one unit to B(Slave Bridge)
2. Connect the POE to each unit by the Ethernet cable and plug the POE in;
3. Wait for them to power up, about 2 min;
4. Use the tiny reset button to click through until you get a channel with a
letter. 1,2,3,..., A,B,C,...,F
5. Then on the other unit do the same. Both units need to be on the same
channel;
6. Wait for 2-5 minutes to complete the pairing. When the number of the
digital tube is solid and the signal light on the side turns on, it means the
pairing is successful;
7. Finally connect other devices(Router, PC, Switch) and install them to the
target location.
（TIPS: Steps 1, 4 and 5 are already pre-set）

[email protected] 07
5.3 Point to Multi-point Pairing Step:
e.g. 1 Master bridge with 3 slave bridges
1. Switch one unit to A(Master Bridge) and 3 units to B(Slave Bridge);
2. Connect the POE to each unit by the Ethernet cable and plug the POE in;
3. Wait for them to power up, about 2 min;
4. Use the tiny reset button to click through until you get a channel with a
letter. 1,2,3,..., A,B,C,...,F
5. Then on the other 3 unit do the same. 4 units need to be on the same
channel;
6. Wait for 2-5 minutes to complete the pairing. When the number of the
digital tube is solid and the signal light on the side turns on, it means they
pairing is successful;
7. Finally connect other devices (Router, PC, Switch) and install them to the
target location.
★Note:
For point-to-point installation, the line of sight of the 2 wireless bridge
must be clear and cannot pass through the wall. The signal transmission
angle of the bridge is 60 degrees. For point to multi-point installation, the
angle of the slave bridge needs to be adjusted to ensure that it is within
the 60-degree signal range of the main bridge. The antenna polarization
direction is horizontal 60°/vertical 30°.

6. Installation
[email protected]
08
6.1 Pole mount
6.2 Wall-mounted
6.3 Connect to the device
POE

[email protected] 09
1. Choose to pole mount or wall-mounted, adjust the CPE orientation, the
bracket is not included in the package. Recommended ULNA Universal
Bracket (ASIN: B0BCNZFNTD).
2. Prepare a long enough network cable to connect the PoE port of the PoE
adapter and LAN port of the CPE. Recommend to use a cat 5 (or above)
shielded network cable with a ground wire.
3. Connect the PoE port of PoE adapter to CPE, and the LAN port of PoE
adapter to Camera, PC, Router or Switch based on the network topology.
The role of PoE is to provide power and data transmission for CPE.
4. When the WiFi Bridge is used to extend network, please connect the
1000Mbps LAN port of Master Bridge/ LAN port of PoE adapter to the
Ethernet, and connect the 1000Mbps LAN port of Slave Bridge/LAN port of
PoE adapter to routers or other devices.
5. When the WiFi Bridge is used to extend surveillance 'cameras range,
please connect the 1000Mbps LAN port of Master Bridge/LAN port of PoE
adapter to the monitor, and connect the 1000Mbps LAN port of Slave
Bridge/LAN port of PoE adapter to cameras.
★Note:
For point to point installation, the line of sight of the 2 wireless bridge must
be clear and cannot pass through the wall. The signal transmission angle
of the bridge is 60 degrees.
For point to multi-point installation, the angle of the slave bridge needs
to be adjusted to ensure that it is within the 60-degree signal range of
the main bridge. The antenna polarization direction is horizontal 60°/
vertical 30°.

7. WiFi Function
[email protected]
10
2.4G WiFi
CPE5G_2G1
cpe1234567890
5.8G WiFi
WiFi SSID: CPE5G-5GXX
WiFi PWD: cpe12345678XX
XX represents different channels, please refer to the comparison table in
the user manual.
★Note:
You can access the wireless bridge through your computer to set the SSID
and new WiFi password. Please refer to the advanced settings section.
Digit on/off
Digit on/off is enable
General 5.8Ghz WiFi of
master bridge works
General 5.8Ghz WiFi of
slave bridge doesn’t work
Guest 5.8Ghz WiFi of
master bridge works
Guest 5.8Ghz WiFi of slave
bridge works
General 5.8Ghz WiFi of
master bridge works
General 5.8Ghz WiFi of
slave bridge works
Guest 5.8Ghz WiFi of
master bridge doesn’t work
Guest 5.8Ghz WiFi of
master bridge doesn’t work
Digit on/off is disable

8. Application Case
[email protected] 11
8.1 Case 1: Point to point extend network WiFi range
8.2 Case 2: Point to point extend surveillance cameras range
8.3 Case 3: Point to multi-point extend surveillance cameras range
Extending the network to second buildings, such as garages, shops, barns,
etc.
Internet ADSL
LAN WAN
Computer

[email protected]
12
8.4 Case 4: Point-to-point extend surveillance cameras range
9. Advanced Settings
Note:
The wireless bridge can work without advanced settings
POE injector
100M port
AP
1000M port
1. Computer access Wireless Bridge, connect the CPE to the computer
Refer to the figure to connect the CPE to the computer through a PoE
injector and an Ethernet cable.

2. Modify your computer's IP address, make your computer's IP and the
bridge's IP address be on the same network segment(LAN) so that you
can access them.
3. Change your computer's IP address to 192.168.255.xxx (192.168.255.xxx
cannot be the same as the IP of the CPE), then entry IP address is
192.168.255.xxx, the subnet mask is 255.255.255.0(Auto fill), the Default
gateway is 192.168.255.xxx, Preferred DDS server 192.168.255.xxx. You can
use 192.168.255.105(xxx=5) in the reference picture to set.
Step 1: Find and open "Open Network and Sharing Center" on your
computer. Tips：click the network icon in the lower right corner of the
computer.
Step 2：Find and open the "Change adapter settings", select "Local Area
Connection" to right-click to open the network properties. Refer to the
picture above to open.
Step 3: Find and double-click open the "Internet Protocol Version 4
(TCP/IPv4)", choose the " Use the following IP address" and enter IP
address, Subnet mask, Default gateway, Preferred DDS server.
[email protected] 13

[email protected]
14
4. On the login screen, the default user name and login password of the
wireless bridge is "admin", just entry password login.
5. Login successful, go to setting.
5.1 Language - ULNA Wireless Bridge CPE629D support English&Chinese,
you can choose the language on this page
★Note:
“admin” is not the password of the WiFi SSID, it is just the password for WEB
access.
Login
User Name
admin
Password
admin

[email protected]
15
5.2 Digit on/off
Digit on/off” Enable - the bridges are pairing by switching the A-B button
and short click the reset button to select a channel;
Digit on/off” disable - the bridges are pairing by manually selecting a
channel and A/B bridge on the Web page. Digital tube showing the letter”H”.
5.2.1 Disable Digit on/off” - Selecting Master/Slave Bridge
5.2.2 Disable Digit on/off” - Selecting a channel

[email protected]
16
5.4 Wireless 2.4Ghz Setting
5.4.1 SSID & Password
SSID: CPE5G_2G1
Password：cpe1234567890
5.3 Watchdog - You can enable or disable watchdog function on this
page
★Note:
You can change the SSID and password on this page. Please remember
the new SSID and password. If you forget it, you have to reset the device.

[email protected] 17

[email protected]
18
5.4.2 Radio Channel - The 2.4G band is subject to high levels of
interference, you can be change other channels when interference causes
poor signal. We recommend you to select the Autoselect.