Ultra Start 42xx User manual

-The system must be placed into Service Mode before any service work is started on the vehicle. It is
the sole responsibility of the vehicle owner to ensure that this is done. The manufacturer accepts no
liability or responsibility for accidental starting of the vehicle.
- CARBON MONOXIDE - Never Start in an Enclosed Building (Garage, Carport etc...)
- The Hood Pin Safety Switch Must Always be Installed!
- Never Install Automatic Transmission Remote Starters into a Manual Transmission Vehicle!
Covers All 42xx and 43xx Series Remote Starter/Alarms

OWNER’S GUIDE 2WAY REMOTE STARTER/ ALARM
Page 2
This device complies with Part 15 of the FCC rules. Operation of this device is subject to
the following conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the part responsible for
compliance voids the users authority to operate this device.
Congratulations on your purchase of an Ultra Start 2way remote vehicle starter with alarm
Ultra Start remote vehicle starters will provide years of comfort and convenience. To utilize
and understand this system to the fullest, please read this manual in detail.
FCC Notice
Welcome
It is our continuing objective to design and manufacture the absolute best Remote Car
Starters, Vehicle Security Systems, Keyless Entry Systems and Security Bypass units
available in today’s competitive market. This objective is met by utilizing installation
professionals with decades of industry experience to assist in each step of the design
process. This has allowed us to build products that are very installer and user friendly yet
offer advanced and innovative features. Our systems utilize intelligent programming and
auto learning systems and are designed to work properly in every vehicle. Our systems are
also designed wherever possible to be easily enhanced, allowing the consumer and the retailer
to enjoy easy and cost effective upgrades and additions to their system down the road. Our
limited lifetime warranty provides one of the best protection plans in the industry, giving
both the consumer and the retailer confidence when they invest in an Ultra Start product.
About Ultra Start
Feature List
- Remote Keyless Entry. - Panic Mode. (Personal Protection)
- Engine Idle Mode. - Turbo Timer Mode.
- Starter Disable. - Anti-Grind Protection.
- Dual Car Operation. - User Extendable Runtime.
- Safety Start Mode. - System Override Protection.
- Remote Service Mode. - Dual Stage Shock Sensor.
- Park Light Diagnostics. - Up to 4 Different Transmitter Codes.
- Ignition Auto Locks. - Cold Start Mode With 4 Start intervals.

2WAY REMOTE STARTER/ ALARM OWNER’S GUIDE
Page 3
Remote Start - Automatic Transmission Only
1.Press and release button #3.
2.The park lights will flash and the siren will chirp one time.
3.The vehicle will then remote start. The park lights will flash four times then
remain on while the vehicle is running.
4. The vehicle will run for the programmed runtime, (normally 15 minutes.)
Note: If the remote starter fails to start, the park lights will flash a Trouble Shooting
Code. Count the number of flashes and refer to the Diagnostics Chart.
Never remote start if the vehicle is parked in a Garage or attached
carport! Operate in a well ventilated area only.
Remote Stop
1.Press and hold button #3 for three seconds. The remote starter will shut down.
The park lights will flash and the siren will chirp two times to confirm shutdown.
Note: Pressing the brake pedal or opening the hood will also shut down the remote
starter.
Idle Mode
1.While the vehicle is running with key, press button #3.
2.The park lights will turn on and the siren will chirp once.
3.Turn the ignition key off and the vehicle will continue to run.
4. Exit the vehicle and leave it running safely without leaving the keys in the Ignition.
Lock the door while the vehicle is left running.
Extended Run Time
Turbo Timer Mode
1.While the vehicle is running with key, press button #4.
2.The park lights will turn on and the siren will chirp once.
3.Turn the ignition key off and the vehicle will run for approximately 2 minutes.
1.Press and release Button #3 while the vehicle is running under the remote starter.
The park lights will flash and the horn (optional) will honk to confirm the runtime has
been extended. The system will reset the runtime (normally 15 minutes).
Note: The Run timer is not updated with this feature.
1234
1234
1234
1234
123
4

Page 4
OWNER’S GUIDE 2WAY REMOTE STARTER/ ALARM
Reservation Mode - Manual Transmission Vehicles
Manual transmission remote starters must be set into Reservation Mode before
the remote starter will activate. There are two different ways to place the system
into Reservation Mode. The activation type of Reservation Mode is determined
when the system is installed. The default setting is Auto Reservation Mode.
Auto Reservation Mode
Step 1 - While the vehicle is running with the key, place the transmission into neutral
and apply the park brake.
Step 2 - Press and release the brake pedal twice. The park lights will flash twice,
the siren will chirp twice and the doors will unlock (optional).
Step 3 - Turn the ignition key off and the vehicle will continue running.
Step 4 - Exit the vehicle and close all the doors. The vehicle will then shut off *.
Manual Reservation Mode (Dealer Programmable Feature)
Step 1 - While the vehicle is running with the key, place the transmission into neutral
and apply the park brake.
Step 2 - Press and release button #4. The park lights will flash twice, the siren
will chirp twice and the doors will unlock (optional).
Step 3 - Turn the ignition key off and the vehicle will continue running.
Step 4 - Exit the vehicle and close all the doors.
Step 5 - Press and hold button #3 for 3 seconds, the vehicle will then shut off.
*****THE VEHICLE MAY NOW BE SAFELY REMOTE STARTED.*****
(See page 4 for Remote Starter Functions.)
If Reservation Mode is not set, the remote starter will not activate. When button #3
is pressed the park lights will flash 4 times. 4 flashes is the diagnostic
code for “Not in Reservation Mode”
Note: Reservation Mode will reset if the doors of the vehicle are opened. To re-enter
the vehicle without canceling the Reservation Mode (forgot something..) The
vehicle must first be remote started. While the vehicle is running the door may
be opened, when done in the vehicle, close the door and hold button #3
until the remote starter shuts off.
* If the vehicle has dome light delay, the vehicle may stay running until the dome
light turns off. This is normally no longer than 30 seconds.

ACTIVATE PANIC MODE
1. Press and hold Button #1 for three seconds.
2. The park light will begin to flash and the siren will activate.
PANIC MODE DISABLE
- Press and release Button #1 to disable Panic Mode and lock the doors.
- Press and release Button #2 to disable Panic Mode and unlock the doors.
Note :Panic Mode will stay activated until disable by the remote
Transmitter.
Page 5
2WAY REMOTE STARTER/ ALARM OWNER’S GUIDE
1. Press and hold button #2 and the doors will unlock,
continue holding the unlock button, the trunk release will activate. The
trunk release will be confirmed by one park light flash and one siren chirp.
Note: The trunk release output will not activate when the ignition key is in the
On position.
(Optional to button #4*)
*The trunk release output may be programmed to operate on button #4.
1.Press and release button #1 on the remote transmitter.
2.The park lights will flash and the siren will chirp one time.
3.The doors will lock.
4.The LEDs on the antenna will start flashing within five seconds.
Note: If installed, the starter disable will activate.
* To Lock without siren chirps, press buttons #1 and #2 at the same time.
1.Press and release button #1 on the remote transmitter.
2.The park lights will flash and the siren will chirp two times.
3.The doors will unlock.
4.The LEDs on the antenna will stop flashing.
Note: If installed, the starter disable will deactivate.
* To Lock without siren chirps, press buttons #1 and #2 at the same time.
Lock Doors and Arm Alarm
Alarm Features
Unlock Doors and Disarm Alarm
Trunk Release
1. Press and hold button #2 and #3 for 3 seconds.
2. The park lights will flash and the siren will chirp five times.
3. The remote will beep and display the systems current status.
Car Finder Mode
Panic Mode
1234
1234
1234
1234
1234

Page 6
OWNER’S GUIDE 2WAY REMOTE STARTER/ ALARM
Press and release button #1 to arm the alarm then press and release button #3
within three seconds. The system will chirp once when the lock button is
pressed and once when the start button is pressed. The shock sensor
will be disabled until the system is disarmed and the rearmed again
Press and release buttons #1 and #2 at the same time. If the doors were
locked this will unlock the doors without chirping the siren.
Note: The park lights will flash as confirmation of lock/ unlocking.
To Enter Shock Sensor Programming
Press and hold buttons #1 and #2 for three seconds. The park lights will flash
and the siren will chirp three times.
While the park lights are on strike the vehicle with the amount of force
wanted to trigger the alarm*. Hit the vehicle with the same amount of
force three time, the siren will chirp each time the system detects the
Impact
.
*Strike the vehicle with the palm of the hand, be careful not to impact
the vehicle in a area that may cause damage. The most common
location for testing and setting the shock sensor is the A-pillar. The A-
Pillar is the metal support that runs from the roof of the vehicle to the
hood area. Avoid hitting the windshield when programming the shock
Sensor.
Temporary Shock Sensor Bypass
Silent Arm and Disarm
Shock Sensor Programming/ Adjustment
Alarm Features
1
1
1
2
2
2
3
3
3
4
4
4

Page 7
2WAY REMOTE STARTER/ ALARM OWNER’S GUIDE
Cold Start Mode will start the vehicle at a user selectable start interval or
temperature setting. The vehicle can be set to start once every 1, 2, 3 or
4 hours in Timer Mode or to start at 0,-5,-15 or -25 Celsius in Temperature
Mode (LT Models Only) for a maximum 12 starts. The vehicle will start at
the selected start interval/ temperature and run for the programmed runtime
(Normally 15min). Cold Start Mode must be set each time the user wishes to
Use this feature.
Example- Timer Mode. If the 4 hour start cycle was selected, the
vehicle will start once every 4 hours and run for the programmed runtime
then turn off. This setting will keep the vehicle in Cold Start Mode for up
to 2 days before deactivating.
Example- Temp Mode (LT models only). If the -15 Celsius start cycle
was selected, the system will monitor the temperature until it falls below
-15, at this time the remote starter will activate for the programmed runtime.
The system will then wait 2 hours before checking the temperature again.
To Enter Cold Start Mode.
Method 1- Press and release button #4, then press and hold button #3
for 6 seconds or until park lights turn on.
Method 2 - Press and hold buttons #1 and #3 at the same time for 3
seconds. The park lights will turn on.
While the park lights are on the start cycle can be selected.
1 hour or 0C Press Button #1 1 Park light flash
2 hour or -5C Press Button #2 2 Park light flashes
3 hour or -15C Press Button #3 3 Park light flashes
4 hour or -25C Press Button #4 4 Park light flashes
Note: The optional Low Temp sensor must be installed for the temperature
settings to be available. (LT Models only)
To Cancel Cold Start Mode
Method 1- Press and release button #4, then press and hold button #3 for
six seconds.
Method 2- Press and hold buttons #1 and #3 at the same time for 3
seconds.
Note: Stepping on the brake or turning on the ignition will cancel Cold Start.
cancellation of Cold Start Mode will be confirmed with two park light flashes
and two siren chirps.
*****Never remote start or set the Cold Start Mode if the vehicle is
parked in a Garage or Attached Carport!
Cold Start Mode
123
4
123
4

Page 8
OWNER’S GUIDE 2WAY REMOTE STARTER/ ALARM
LCD DISPLAY
TELEPHONE ICON- When the vehicle starts in Timer Mode, this icon will appear
in conjunction with the usual icons that indicate that the vehicle is running by the
remote starter.
KEY ICON- This icon will begin to flash when the remote starter button is first
pressed. After the vehicle has started this icon will stay on solid. The wheels on the
car will begin to rotate.
HORN ICON- This icon indicates that the alarm has been triggered. The remote
will start to beep and the siren icon will come on solid at the same time as the icon
for the violated zone. The remote will stop beeping after one minute. Both icons will
continue to flash until the system is disarmed.
ANTENNA ICON- This icon will be visible on the LCD whenever the remote
is within transmitting range of the vehicle. The icon will disappear when the remote
leaves that transmitting range.
STATUS ICONS These icons are located at the top of the LCD screen.
STATUS CHECK MODE This feature is used to check the status of the alarm system or
the remote starter.
1. To check the status press and release Button #4 on the remote transmitter.
2. The remote will display the icons of the active features on the LCD screen.
TRUNK ICON- This icon will be displayed on the LCD screen when the trunk
release output is activated by the remote transmitter. This icon will be displayed on
the screen until the system is armed or if the status button is pressed
BATTERY ICON- This icon is always present when the LCD screen. This icon will
indicate the current battery level for the remote transmitter. The black area of the
icon will disappear as the battery level decreases.
RUN TIMER- This icon activates during remote starting. The bar graph will count
down in 2 minute increments, indicating how much time is left on the remote starter’s
runtime.

Page 9
2WAY REMOTE STARTER/ ALARM OWNER’S GUIDE
To Enter Clock Adjust Mode
Press and hold buttons #1 and #4 until the minute portion of the clock located on
the LCD begins to flash
.
To Adjust The Time of day
To set the minute, press and release button #3 to increase the minute or press
button #2 to decrease the minute. To set the hour, press and release button #1
and the hour portion of the clock will begin to flash. To set the hour, press and
release button #3 to increase the hour and button #2 to decrease the hour. To set
the AM/ PM icon, continue changing the hour until the appropriate icon is
displayed.
Note: The remote will exit clock adjust if there is no activity for 20 seconds.
Setting The Digital Clock
1234
When the Battery Icon on the remote transmitter indicates that the
battery is low the battery should be changed promptly. Replace with a
quality 1.5volt “AAA” battery.
Battery Replacement
1234
aB tt rey
Slide
Bttraey
Lift
Slide
trBtey
a
Positive
Negative
Note- Avoid reinstalling the battery in the wrong direction

Page 10
OWNER’S GUIDE 2WAY REMOTE STARTER/ ALARM
ATTENTION: TO AVOID SERIOUS INJURY, this remote start system must be set into
Service Mode before any under hood servicing is started. Service Mode will prevent
the vehicle from starting while the vehicle is being serviced. It is the sole
responsibility of the vehicle’s owner to place the system into Service Mode. The
manufacture accepts no responsibility for accidental starting of the vehicle while the
vehicle is being serviced.
Emergency Service Mode - (Valet)
This feature will disable the system except for locking and unlock functions.
This mode can also used if a remote is lost, damaged or if the system malfunctions.
ENTERING SERVICE MODE
1.Turn the ignition key to the “On” position then press and hold the Program Button on
the antenna for 5 seconds or until siren chirps 5 times.
EXITING SERVICE MODE
1.Turn the ignition key to the “On” position then press and hold the Program Button for 5
seconds or until the siren chirps 2 times.
Note: Remote starter functions will be disabled and the LED will be “on” steady.
The door locks and the trunk release will still be operational.
System Service Mode(Valet) - By Remote
This feature will disable the system from the remote transmitter. This feature must be
used when having the vehicle serviced. ( Oil change, Tune-up etc.)
ACTIVATE Service Mode
Press and release then press and hold button #4 for 5 seconds.
The park lights will flash and the siren will chip 5 times to confirm that the system
has entered Service Mode.
Note: Remote starter functions will be disabled and the LEDs will be “on” steady. The
door locks and the trunk release will still be operational.
DEACTIVATE Service Mode
Press and release then press and hold button #4 for 5 seconds.
The park lights will flash and the siren will chip 2 times to confirm that the system
has exited Service Mode.
Note: Remote starter functions will be disabled and the LEDs will be “on” steady. The
door locks and the trunk release will still be operational.
Service Mode