Ultra Start 2600 User manual

WWW.ULTRASTARTERS.COM
OWNER’S GUIDE
AUTOMATIC AND MANUAL
TRANSMISSION MODELS
Advanced Remote Vehicle
Starter With Security
System
26002600
2600M2600M
FCC/ID Notice
ATTENTION This device complies with Part 15 of the FCC rules. Operation is
subject to the following conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by
the part responsible for compliance void the user’s authority to
operate this devise.
!
-The system must be placed into Service Mode before any service work is started on the
vehicle. It is the sole responsibility of the vehicle owner to ensure that this is done. The
manufacturer accepts no liability or responsibility for accidental starting of the vehicle.
- CARBON MONOXIDE - Never Start In AEnclosed Building (Garage, Carport etc...)
- The Hood Pin Safety Switch MustAlways Be Installed!
- Never Install Automatic Transmission Remote Starters On Manual Transmission Vehicles!

Owners Guide
Owner’s Guide
1.Press and release the #button, then press and hold the button for six seconds. The parking lights turn “On” to
confirm entering Low Temperature Mode.
2. Whilethe parklightsare“on”thestartcycle canbeselected.
1 hour cycle or 0c Press the LOCK button 1 park light flash
2 hour cycle or -5c Press the UNLOCK button 2 park light flashes
3 hour cycle or -15c Press the button 3 park light flashes
4 hour cycle or -25c Press the button 4 park light flashes
3. The system will start the vehicle at the selected start cycle. The vehicle will run for it’s runtime then shut off.The
system will repeat this for a maximum 24 hour period.
1. Press and release the #button, then press and hold the button for four seconds.
2. The System will respond with two flashes and two horn honks (optional).
Note: Remote starting or starting with the key will also cancel Timer/ Temp Mode.
4. The temperature sensor must be installed for temperature activation. The system will only
trigger 1 time each 2 hours. If the sensor is not installed the unit will activate the timer mode.
1. Press and release the button.
2. The Park lights will flash and the horn(optional) will honk one time.
3. When the vehicle has started, the park lights four times then remain “On” while the vehicle is running.
4. The vehicle will continue to run for the programmed runtime. (normally 15 minutes).
1. Press and release the button while the vehicle is remote started.
2. The system will respond with one park light flash and one horn honk (optional) to
confirm Extended Runtime. The system will reset the run time, (normally 15 minutes).
1. Press and hold the #button for two seconds.
2. Thesystemwillflashtheparklightsandhonkthehorn(optional)fivetimes.
3.Thisfeaturecanhelpfindyourvehicleinacrowdedparkinglot.
1. Press and hold the UNLOCK button for three seconds.
2. Thedoorswillunlock,continueholdingtheunlockbuttonforthreemoreseconds,thetrunkreleasewill thenactivate.
Thetrunkreleasewillbeconfirmedbyoneparklightflash.
Note:Thetrunkreleaseoutputwillnotactivatewhentheignitionkeyisinthe“On”position.
1. Press and release the LOCK button on the remote transmitter.
2. The park lights will flash and the horn (optional) will honk one time.
3. The doors will lock. (With Keyless Entry option)
4. The LED’s on the antenna will start flashing within five seconds.
1. Press and release the UNLOCK button on the remote transmitter.
2. Theparklightswillflashandthehorn(optional)willhonktwotimes.
3. Thedoorswillunlock.(WithKeylessEntryoption)
4. TheLED’sontheantennawillstopflashing.
OptionalDriver’sDoorUnlockFeature
Thedriver’sdoorunlockfeature willunlockthedriver’sdoorseparatelyfromtheotherdoors.
1. Pressandrelease theUNLOCKbuttononcetounlockdriver’sdoor.
2. Pressandrelease asecondtimewithintwosecondstounlockallotherdoors.
1. Press and hold the LOCK button for three seconds.
2. The park lights will flash and horn will honk (optional)
PANIC MODE DISABLE
- Press the LOCK button to disable the panic mode and to lock the doors.
- Press the UNLOCK button to disable the panic mode and unlock the doors.
- Panic Mode will stay activated until disabled by the remote transmitter.
1. Press and release the LOCK & UNLOCK buttons at the same time.
2. If locked this will unlock the doors without honks, the park lights will flash two times to confirm the doors unlocked.
3. If unlocked this will lock the doors without honks, the park lights will flash one time to confirm the doors locked.
Lock Doors Reservation Mode - Manual Transmission Models Only
Remote Start
Extended Run Time
Remote Stop
Idle Mode
Timer/ Optional Temperature Start Mode.
To Cancel Timer/ Temperature Start Mode.
Unlock Doors
Silent Lock And Unlock
Trunk Release
Car Finder Mode
Panic Mode
1. Press and hold the button for three seconds. The remote starter will shut down.
2. The park lights will flash two times and the horn(optional) will honk two times.
Note: Pressing the brake pedal or opening hood will also deactivate the remote starter.
1. While the vehicle is running with key, press the button.
2. The park lights will turn on and the horn(optional) will honk once.
3. Turn the ignition key “Off” and the vehicle will continue to run.
4. Exit the vehicle and leave it running without the keys.Always lock the doors if the vehicle is left running.
BASIC OPERATIONS REMOTE STARTER FEATURES
2nd Car Operation
23
#
Press the # button at the same time as the command for the second car. This feature requires Special programming
Diagnostics
TO INSURE SAFE STARTING OF MANUAL TRANSMISSION VEHICLES
1. With the vehicle running, apply the park brake then press and release the brake pedal.
2. The park lights will flash and the horn will honk (optional) to confirm that reservation mode has been activated.
3. Remove the key from the ignition, and exit the vehicle. (The vehicle will remain running until the door is closed)
4. The vehicle will shut off. (If the vehicle has a delay dome-light, the vehicle may run until the dome-light turns off)
THE VEHICLE IS NOW IN RESERVATION MODE AND MAY BE REMOTE STARTED.
Note: To enter the vehicle without canceling the Reservation Mode, the remote starter must be On while the door is opened
then closed. For safety reasons, Reservation Mode must be reset each time a door is opened while the engine is off.
Auxiliary 1 - Channel 3/ Button 5
Auxiliary 2 - Channel 4/ Button 6
Press and hold button #5. The doors will unlock and the siren will chirp twice, continue to hold the button and the
output will activate followed by one chirp. This output can be used for addition accessories such as sliding door
control and window roll up. See dealer for details.
Press and hold button 6. The doors will unlock and the siren will chirp twice, continue to hold the button and the
output will activate followed by one chirp. This output can be used for addition accessories such as sliding door
control and window roll up. See dealer for details.
PARK LIGHTS STATUS LED DIAGNOSTIC CODE
3 Flashes Series of 3 Flashes Door Opened “M” Models
3 Slow Flashes LED’s On Solid System Is In Service Mode
4 Flashes Series of 4 Flashes Hood or Brake before start
4 Slow Flashes Series of 4 Flashes Not in Reservation Mode “M” units
5 Flashes Series of 5 Flashes Brake Pedal Shutdown
6 Flashes Series of 6 Flashes Hood Pin Grounded
7 Flashes Series of 7 Flashes Tach Lock-Out
8 Flashes Series of 8 Flashes 3 Start Attempts with no start
If the system fails to start, a diagnostic will be displayed by the vehicles park lights. Count the number of flashes then compare to the
chart below. The system will not function until the problem causing the code is corrected.
Lock doors. (Hold For Panic Mode)
Press again and hold for constant Lock.
Press Once to Unlock the doors.
Press & Hold for Trunk / Channel 3
Remote Start -(2 Times for Safety Start)
For 3 seconds to shut down the starter.
EnterTimer/ Temperature Mode
To activate Aux 1(Sliding Door etc..)
To activate Aux 2(Sliding Door etc..)
Hold 6 seconds to enter/ exit Service Mode
For 2 seconds for Car Finder
=
=
==
==
=
=
&
&
&
&
&
&
Then
Then

Owners Guide
Owner’s Guide
1.Press and release the #button, then press and hold the button for six seconds. The parking lights turn “On” to
confirm entering Low Temperature Mode.
2. Whilethe parklightsare“on”thestartcycle canbeselected.
1 hour cycle or 0c Press the LOCK button 1 park light flash
2 hour cycle or -5c Press the UNLOCK button 2 park light flashes
3 hour cycle or -15c Press the button 3 park light flashes
4 hour cycle or -25c Press the button 4 park light flashes
3. The system will start the vehicle at the selected start cycle. The vehicle will run for it’s runtime then shut off.The
system will repeat this for a maximum 24 hour period.
1. Press and release the #button, then press and hold the button for four seconds.
2. The System will respond with two flashes and two horn honks (optional).
Note: Remote starting or starting with the key will also cancel Timer/ Temp Mode.
4. The temperature sensor must be installed for temperature activation. The system will only
trigger 1 time each 2 hours. If the sensor is not installed the unit will activate the timer mode.
1. Press and release the button.
2. The Park lights will flash and the horn(optional) will honk one time.
3. When the vehicle has started, the park lights four times then remain “On” while the vehicle is running.
4. The vehicle will continue to run for the programmed runtime. (normally 15 minutes).
1. Press and release the button while the vehicle is remote started.
2. The system will respond with one park light flash and one horn honk (optional) to
confirm Extended Runtime. The system will reset the run time, (normally 15 minutes).
1. Press and hold the #button for two seconds.
2. Thesystemwillflashtheparklightsandhonkthehorn(optional)fivetimes.
3.Thisfeaturecanhelpfindyourvehicleinacrowdedparkinglot.
1. Press and hold the UNLOCK button for three seconds.
2. Thedoorswillunlock,continueholdingtheunlockbuttonforthreemoreseconds,thetrunkreleasewill thenactivate.
Thetrunkreleasewillbeconfirmedbyoneparklightflash.
Note:Thetrunkreleaseoutputwillnotactivatewhentheignitionkeyisinthe“On”position.
1. Press and release the LOCK button on the remote transmitter.
2. The park lights will flash and the horn (optional) will honk one time.
3. The doors will lock. (With Keyless Entry option)
4. The LED’s on the antenna will start flashing within five seconds.
1. Press and release the UNLOCK button on the remote transmitter.
2. Theparklightswillflashandthehorn(optional)willhonktwotimes.
3. Thedoorswillunlock.(WithKeylessEntryoption)
4. TheLED’sontheantennawillstopflashing.
OptionalDriver’sDoorUnlockFeature
Thedriver’sdoorunlockfeature willunlockthedriver’sdoorseparatelyfromtheotherdoors.
1. Pressandrelease theUNLOCKbuttononcetounlockdriver’sdoor.
2. Pressandrelease asecondtimewithintwosecondstounlockallotherdoors.
1. Press and hold the LOCK button for three seconds.
2. The park lights will flash and horn will honk (optional)
PANIC MODE DISABLE
- Press the LOCK button to disable the panic mode and to lock the doors.
- Press the UNLOCK button to disable the panic mode and unlock the doors.
- Panic Mode will stay activated until disabled by the remote transmitter.
1. Press and release the LOCK & UNLOCK buttons at the same time.
2. If locked this will unlock the doors without honks, the park lights will flash two times to confirm the doors unlocked.
3. If unlocked this will lock the doors without honks, the park lights will flash one time to confirm the doors locked.
Lock Doors Reservation Mode - Manual Transmission Models Only
Remote Start
Extended Run Time
Remote Stop
Idle Mode
Timer/ Optional Temperature Start Mode.
To Cancel Timer/ Temperature Start Mode.
Unlock Doors
Silent Lock And Unlock
Trunk Release
Car Finder Mode
Panic Mode
1. Press and hold the button for three seconds. The remote starter will shut down.
2. The park lights will flash two times and the horn(optional) will honk two times.
Note: Pressing the brake pedal or opening hood will also deactivate the remote starter.
1. While the vehicle is running with key, press the button.
2. The park lights will turn on and the horn(optional) will honk once.
3. Turn the ignition key “Off” and the vehicle will continue to run.
4. Exit the vehicle and leave it running without the keys.Always lock the doors if the vehicle is left running.
BASIC OPERATIONS REMOTE STARTER FEATURES
2nd Car Operation
23
#
Press the # button at the same time as the command for the second car. This feature requires Special programming
Diagnostics
TO INSURE SAFE STARTING OF MANUAL TRANSMISSION VEHICLES
1. With the vehicle running, apply the park brake then press and release the brake pedal.
2. The park lights will flash and the horn will honk (optional) to confirm that reservation mode has been activated.
3. Remove the key from the ignition, and exit the vehicle. (The vehicle will remain running until the door is closed)
4. The vehicle will shut off. (If the vehicle has a delay dome-light, the vehicle may run until the dome-light turns off)
THE VEHICLE IS NOW IN RESERVATION MODE AND MAY BE REMOTE STARTED.
Note: To enter the vehicle without canceling the Reservation Mode, the remote starter must be On while the door is opened
then closed. For safety reasons, Reservation Mode must be reset each time a door is opened while the engine is off.
Auxiliary 1 - Channel 3/ Button 5
Auxiliary 2 - Channel 4/ Button 6
Press and hold button #5. The doors will unlock and the siren will chirp twice, continue to hold the button and the
output will activate followed by one chirp. This output can be used for addition accessories such as sliding door
control and window roll up. See dealer for details.
Press and hold button 6. The doors will unlock and the siren will chirp twice, continue to hold the button and the
output will activate followed by one chirp. This output can be used for addition accessories such as sliding door
control and window roll up. See dealer for details.
PARK LIGHTS STATUS LED DIAGNOSTIC CODE
3 Flashes Series of 3 Flashes Door Opened “M” Models
3 Slow Flashes LED’s On Solid System Is In Service Mode
4 Flashes Series of 4 Flashes Hood or Brake before start
4 Slow Flashes Series of 4 Flashes Not in Reservation Mode “M” units
5 Flashes Series of 5 Flashes Brake Pedal Shutdown
6 Flashes Series of 6 Flashes Hood Pin Grounded
7 Flashes Series of 7 Flashes Tach Lock-Out
8 Flashes Series of 8 Flashes 3 Start Attempts with no start
If the system fails to start, a diagnostic will be displayed by the vehicles park lights. Count the number of flashes then compare to the
chart below. The system will not function until the problem causing the code is corrected.
Lock doors. (Hold For Panic Mode)
Press again and hold for constant Lock.
Press Once to Unlock the doors.
Press & Hold for Trunk / Channel 3
Remote Start -(2 Times for Safety Start)
For 3 seconds to shut down the starter.
EnterTimer/ Temperature Mode
To activate Aux 1(Sliding Door etc..)
To activate Aux 2(Sliding Door etc..)
Hold 6 seconds to enter/ exit Service Mode
For 2 seconds for Car Finder
=
=
==
==
=
=
&
&
&
&
&
&
Then
Then

Remote Service Mode (Valet Mode)
Emergency Service Mode (Valet Mode)
Optional Lifetime or 3 Year Warranty Available on Certain Products
Service Mode disables the remote starter from operating. It will be necessary to activate
Service Mode when having the vehicle serviced.
ENTERINGSERVICEMODE
1. Pressandreleasethe#button,thenwithintwoseconds pressandholdthesame#button
forfivesecondsoruntilthe horn(optional)honksfive times.TheLED’sonthe antennawill
comeonandthenstayonsolidtoconfirmthatthesystemisinServiceMode.
EXITINGSERVICE MODE
1. Pressandreleasethe#button,thenwithintwoseconds pressandholdthesame#button
forfivesecondsoruntilhorn(optional)honks two times.
Note:IftheremotestartbuttonispressedwhenthesystemisinServiceModetheparklights
willflash3times.RemotestartandAlarmfunctionswillbedisabledandtheLED‘swillbe“on”
Solid.Thedoorlocksandthetrunkreleasewillstillbeoperational.
This feature will disable the system except for locking and unlock functions.
Thismodecanalsoused ifaremoteislost,damagedorifthesystemmalfunctions.
ENTERINGSERVICEMODE
1. Whilethe ignitionis“on” pressandholdtheProgram buttonfor5secondsoruntilthehorn
(optional) honksfive times.
EXITINGSERVICE MODE
1. Whilethe ignition is“on” pressand holdtheProgram buttonfor 5 secondsor untilthe horn
(optional)honks twotimes.
Note:RemotestarterfunctionswillbedisabledandtheLEDwillbe“on”steady.
Thedoorlocksandthe trunkreleasewill stillbeoperational.
Ignition
“On”
5 sec.
The manufacturer warrants to the original purchaser of their remote starters and alarms, that the product shall be free from
defectsinmaterialand workmanship.However,shouldthisproduct be proventobedefective,within atwoyearperiodfrom the
original date of purchase, the manufacturer will, without charge to the purchaser (excluding any charges incurred to have the
product delivered to the manufacturer) , repair or replace any part of the remote starter and/or alarm which the manufacturer
agrees to be defective. All warranties apply on to the original purchaser and the vehicle in which it is originally installed.
Repairs or replacement of defective modules shall remain at the discretion of the manufacturer.All other parts, components,
accessories and/or optional equipment pertaining to the remote starter and alarm are not included in the manufacturer’s
warranty. This warranty is non-transferable. Request for warranty service from any Factory Authorized Dealer must be
accompanied with the original purchase receipt or have product registered by authorized dealer on manufacturer’s
website. Failuretocomplywithanyoftheseconditionsmayresultinwarrantybeingvoided.
This warranty does not cover the following: removal and reinstall labour charges, shipping charges, abuse, misuse, or
accidentaldamagestothe remote starterandalarm,automobile, and/or partsthereof. Thiswarrantyisvoiduponmodification,
repairs,oralterationsofany partoftheSystem.Themanufacturerdoesnotguaranteeorinsureagainsttheftofthevehicleorits
contents.Alarmmodels aredesignedonlyto actasadeterrent againstpossibletheft.Thisalarmmayqualify forautoinsurance
discounts,contactyourInsuranceAgentforfurtherinformation.Themanufacturershallnotbeheldliable foranyconsequential
damagesdueto breach of this or any otherwarranty,expressed,orimplied. Thiswarrantygivesyouspecific legal rights.Your
specificlegalrightsmayvaryforeachregion.
CERTAIN DAMAGES EXCLUDED - The manufacturer expressly disclaims any liability or responsibility for incidental
damages caused by the product, including economic loss, loss of use of the product, car rentals, or any other costs relating to
the care and custody of the product. The manufacturer disclaims liability or responsibility for any consequential damages
caused by the product or resulting from its use, including the cost of repairing or replacing other property damaged by the
productorcaused by itsuse, whether or not the product is workingproperly.The product is intendedtodeterunauthorizeduse
of the vehicles in which it is installed. The manufacturer does not warrant that the product is fool-safe against theft and/or
vandalism and/or human error or misuse. The manufacturer accepts no liability or responsibility for any damage of any kind
whatsoever caused to any vehicle in which the product is installed or any resulting damage from its use. The manufacturer
accepts no responsibility or liability for any damage resulting to or theft of the vehicle or its contents, caused or alleged to be
caused,directlyorindirectly,byfailureoftheproduct.
4
WARRANTY
ATTENTION: THE SYSTEM MUST BE PLACED INTO SERVICE MODE BEFORE ANY UNDER HOOD SERVICING IS DONE
TO THE VEHICLE. IT IS THE RESPONSIBILITY OF THE VEHICLE’S OWNER TO INSURE THAT THIS IS DONE. THE
MANUFACTURERACCEPTSNO RESPONSIBILITYFORACCIDENTALSTARTINGWHILEVEHICLEISBEINGSERVICED.
Owner’s Guide
OTHER FEATURES
1st - ½ sec
2nd - 5 sec