Uni-Com Firetide AO-024-MIMO-8 User manual
Version 4.0 October 2014
The contents of this manual are subject to change without
notice. Please refer to the Firetide website, www.firetide.com, for
current information.
© 2014 Firetide, Inc. - A Divion of UNICOM Global
HotPort, HotPoint, HotClient, HotView, HotView Pro,
MeshBridge, and AutoMesh are registered trademarks of Firetide,
Inc. - A Divion of UNICOM Global. All rights reserved.
Antenna & Accessory Guide
For HotPort Mesh Nodes and
HotPoint Access Points
Page 2.
Firetide Connector Chart
Firetide Model Number Antenna Connector Type Firetide Model Number Antenna Connector Type
HotPort 5020-LNK N-female
HotPoint 5100 Indoor AP RP-SMA HotPoint 5200 Outdoor AP N-female
HotPort 7010 Indoor Mesh Node RP-SMA HotPort 7020 Outdoor Mesh Node N-female
Antenna Selection Guide
Firetide offers the following tested and approved antennas. It is the user’s responsibility to insure compliance with all applicable
laws in the country of operation. Note that some high gain antennas may exceed EIRP limits in some countries. Indoor
antennas have RP-SMA connectors, compatible with Firetide HotPort indoor mesh nodes and HotPoint indoor access points.
The outdoor antennas have N connectors.
Band Omni Panel Sector
Model Gain Page Model Gain Page Model Gain Page
Staging ships w product 3 dBi 6
2.4 GHz
AO-024-MIMO-8 9 dBi 8
AOI-245-MIMO-25 2.5 dBi 10
AS-050-N 16 dBi 23
5 GHz
AOI-245-MIMO-25 4.5 dBi 10
AP20-050-MIMO-19 19 dBi
16
AS90-050-MIMO-16T 14 dBi 24
AP-050-N 23 dBi
18
AO-050-N 10 dBi 14
AP5-050-MIMO-28 28 dBi 21
AP10-050-MIMO-23 23 dBi 20
AO-050-MIMO-9 8 dBi 12
4000-1111 7.5 dBi 11
Firetide Antenna & Accessories Guide | Version 4.0 | October 2014
Page 3.
Cable Assembly
CB-015-N Antenna Cable Assembly, 1.5 meter LMR-400 w/ Integrated lightning suppressor N-type
con-nector
CB-015-N-MIMO MIMO Antenna Cable Assembly for 5200 & 7020. 3 in 1 bundled 1.5 meter LMR-400 cables
w/ Integrated lightning suppressor N-type connector
CB-025-N-MIMO MIMO Antenna Cable Assembly for 5200 & 7020. 3 in 1 bundled 2.5 meter LMR-400 cables
w/ Integrated lightning suppressor N-type connector
CB-050-N Antenna Cable Assembly, 5 meter LMR-400 w/ Integrated lightning suppressor N-type
connector
CB-C-015-N Antenna Cable Assembly, 1.5 meter LMR-400
CB-C-015-N-MIMO MIMO Antenna Cable Assembly for 5200 & 7020. 3 in 1 bundled 1.5 meter LMR-400 cables
CB-C-025-N-MIMO MIMO Antenna Cable Assembly for 5200 & 7020. 3 in 1 bundled 2.5 meter LMR-400 cables
CB-C-050-N Antenna Cable Assembly, 5 meter LMR-400
Power Source & Cables
PO-010-N 7000 series outdoor rated 10 meter North America AC power cable
PO-010-E 7000 series outdoor rated 10 meter EU and Korea AC power cable
PO-010-C
7000 series outdoor rated 10 meter UK, Singapore AC power cable
7020-1001 6 pin Female DC power connector for HotPort 7000 series
7020-1002 RF Terminator - 50 ohms - N male
Mounting Solutions
MT-7100 HotPort 7000 family indoor mounting kit for wall, upright, ceiling and office panel installation,
10 machine screws
Spare Parts (Replacement Parts)
SP-7200-03 7020 series Replacement outdoor clawtooth mounting kit
SP-7200-04 7020 series outdoor rated replacement 5 meter North America AC Power cable
SP-7200-02 7020 series Replacement weatherized field installable ethernet RJ45 connector
7000 series Replacement indoor Power Supply Desktop Brick 12VDC
Accessory Guide
Firetide Antenna & Accessories Guide | Version 4.0 | October 2014
PO-010-U
7000 series outdoor rated 10 meter China, Australia and New Zealand AC power cable
SP-POE-1 Indoor power injector for powering 5200/ 5020 series products
SP-7100-01
SP-MNT-01 Replacement part for new panel antenna mounting bracket
Page 4.
4Firetide Accessory Guide Version 3.01 19 June 2009
Most antenna problems are caused by coaxial cable connections that
loosen due to vibration, allowing moisture to penetrate the
connector interface. Firetide recommends that all outdoor cable
connections be weatherproofed using butyl mastic, shown in Figure
1. Butyl mastic is a stretchy, slightly sticky material which bonds to
itself and remains flexible. A layer of electrical tape is used under-
neath to keep the connection clean and make disassembly easier.
Materials Needed:
tPliers
tUtility knife
tVinyl electric tape
tRubber splicing/mastic tape (a.k.a. self-amalgamating, self-
sealing, self-fusing, non-vulcanized)
Waterproofing the Antenna Connection
Step 1
Ensure the connector and cables are free of foreign substances such
as oil, water, grease, or dirt. Fasten connectors securely together.
Use pliers to tighten. Then verify that Firetide node is working, us-
ing HotView™ mesh management software.
Step 2
Tightly wrap a layer of electrical tape, STICKY SIDE OUT, over the
connector from base of unit to one inch over the cable. When
wrap-ping, the tape should overlap about 40% of the previous turn
on each turn. This layer of electrical tape will ease removal of the
mastic tape from the connector if required. Figure 2 shows the use
of a pencil as a wrapping aid if space is tight.
Step 3
Tightly wrap a layer of butyl rubber splicing (mastic) tape over the
electrical tape. Overlapping the tape about 40% on each turn, start
from base of unit and extend at least one inch on to the cable
sheath, as shown in Figure 3.
The key to a good watertight connection is to maintain a high level
of tension and stretch in the butyl rubber.
Step 4
Tightly wrap a layer of electrical tape over the butyl rubber mastic
layer. Then wrap a second layer of electrical tape.The result should
look like Figure 4. The outer layers of electrical tape prevent the
mastic from melting in very hot weather.
Your antenna connector is now weatherized. Next, weatherize the
connection from the cable to the Firetide node.
Waterproofing Instructions
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Firetide Antenna & Accessories Guide | Version 4.0 | October 2014
Page 5.
Firetide. Reliable Connectivity Anywhere. 5
Version 3.01 19 June 2009
Fig. 5a
Fig. 5b
Fig. 6
Fig. 7
Waterproofing the Cable to Node Connections
Waterproofing the connection of the cable to the lighning supressor
and the lightning suppressor to the Firetide node is essentially the
same process as the antenna connector.
Step 5
Wrap a layer of electrical tape, STICKY SIDE OUT, around the
supres-sor-to-node connection, as shown in Figure 5b and 5c. Repeat
for the cable-to-suppressor connection.
Step 6
Using plenty of tension, tightly wrap a layer of butyl rubber splicing
(mastic) tape over the electrical tape. Overlapping the tape about 40%
on each turn, start from base of unit and extend at least one (1) inch
on to the cable sheath, as shown in Figure 6.
The key to a good watertight connection is to maintain a high level
of tension and stretch in the butyl rubber.
Step 7
Tightly wrap two layers of electrical tape over the butyl mastic,
sticky side in, as shown in Figure 7.
Your system is weatherized. Don’t forget to leave a drip loop when
installing the Firetide node and antenna.
Fig. 5c
Firetide Antenna & Accessories Guide | Version 4.0 | October 2014
Page 6.
Firetide 2.4 and 5.X GHz Dipole Staging Antenna
The Firetide 2.4 and 5.X GHz Dipole staging antenna is shipped with
the Firetide HotPort and HotPoint product line. These 3dBi indoor
omnidirectional antennas assist in the network staging process and
their easy-on-eye appearance blends smoothly with the Firetide
hardware.
NOTE: Staging antenna designed for indoor use only and
recommend-ed application is to use in network staging process.
continued on next page
Electrical Specifications Value
Frequency Range 2.4 – 5.X GHz
Gain 3 dBi
Radiation Pattern Omnidirectional
VSWR (Voltage Standing Wave Ratio) ≤ 2.0
Impedance 50 Ω
Polarization Vertical
Operating Temperature -20°C – 65°C
Mechanical Specifications
Connector Type RP-SMA
Order Number
2.4 and 5.X GHz Dipole*
*staging antenna ships with products
2300–2500 MHz: VPol.
H Plane
2500–2700 MHz: VPol.
E Plane
Firetide Antenna & Accessories Guide | Version 4.0 | October 2014
Page 7.
Firetide 2.4 and 5.X GHz Dipole Staging Antenna
continued from previous page
Firetide Antenna & Accessories Guide | Version 4.0 | October 2014
Page 8.
Firetide A0-024-MIMO-8 Omnidirectional Antenna
The Firetide A0-024-MIMO-8 8dBi omnidirectional antenna is
designed to provide maximum performance and reliability under
the toughest weather conditions. The antenna features a UV-stable,
vented radome that provides ultimate protection against weather
elements. This antenna can be mast or ceiling mounted.
Benefits
•Vented system design. Provides reliable performance by
protecting the electrical design against extreme moisture
and/or temperatures.
Thread relief on connector. Improved accessibility for•
taping reduces installation time and improves overall
effectiveness.
Internal o-ring seal in the base of the antenna with•
integrated connector at the base. Assures a watertight
seal to prevent water from migrating into the antenna
connector.
Features
High gain, low VSWR•
Small size, light-weight•
Sealed with fiberglass•
Suitable for 2.4 GHz WLAN, Wi-Fi system•
Wireless interface supported: IEEE802.11b,g,n•
Three 2.4 GHz ports•
continued on next page
Electrical Specifications Value
Frequency Range 2400—2500 MHz
Bandwidth 100 MHz
Gain 9 dBi
BeamwidthE-Plane 10°
H-Plane 360°
Electrical Downtilt 10°
Isolation ≤ 25 dB
VSWR (Voltage Standing Wave Ratio) ≥ 1.5
Impedance 50 Ω
Polarization Vertical
Max. Power 20 W
Mechanical Specifications
Connector Type N-Female
Dimensions Ø145 mm x 600 mm
Weight 2 Kg
Pole Diameter Ø40 mm – Ø79 mm H-Plane
E-Plane
Order Number
AO-024-MIMO-8
Firetide Antenna & Accessories Guide | Version 4.0 | October 2014
Page 9.
Firetide A0-024-MIMO-8 Omnidirectional Antenna
Antenna
"L" type bracket
Mast
(supplied
by customer)
600 mm
145 mm
145 mm
600 mm
continued from previous page
Firetide Antenna & Accessories Guide | Version 4.0 | October 2014
Page 10.
Firetide AOI-245-MIMO-25 antenna is a dual-band, MIMO,
ceiling mount antenna designed to provide maximum vertical
polarization. This high performance antenna reduces overhead
clearance requirements and comes in an attractive enclosure. At
an affordable price , this antenna is an ideal choice for building
public safety, retail establishments, enterprise networks, public
“hot spots” and facilities anagement. It comes with a steel
mounting kit.
Applications
2.4G/5G WLAN system•
Support IEEE802.11a/b/g/n•
Indoor hotspot coverage•
Features
Suitable for indoor use•
Ceiling mount•
Space diversity, MIMO technique•
continued on next page
Firetide AOI-245-MIMO-25 Antenna
Order Number
AOI-245-MIMO-25
Electrical Specifications Value
Frequency Range 2400–2500/5150–5850 MHz
Bandwidth 100/700 MHz
Gain 2.5/4.5 dBi
VSWR (Voltage Standing Wave Ratio)≤ 1.8/2.0
Impedance 50 Ω
Polarization Vertical
Max. Power 50 W
Mechanical Specifications
Connector Type RP-TNC Male/Custom
Dimensions 145 mm x 42 mm
Weight 300 g
Mounting Ceiling Mount
2.4 GHz E Plane
5 GHz E Plane
2.4 H Plane
5 GHz H Plane
Firetide Antenna & Accessories Guide | Version 4.0 | October 2014
Page 10b.
continued from previous page
Firetide AOI-245-MIMO-25 Antenna
Firetide Antenna & Accessories Guide | Version 4.0 | October 2014
Firetide 4000-1111 2.4 GHz Omnidirectional Antenna
This 7 dBi omnidirectional antenna is designed to provide
maximum performance and reliability under the toughest
weather conditions. The antenna features a UV-stable
radome that provides protection against weather.
Typical Value
Frequency Range 2.4-2.5 GHz
Gain 7.4 dBi
Nominal Impedance 50 ohms
VSWR 1.5 Max
Radiation Pattern Omnidirectional
Vertical Beam Width 20°
Polarization Vertical
Connector N, female
Operating Temp Range -20°C to 65°C
Wind Survival 150 MPH
Equivalent Flat Plate Area 7.1 sq. in.
Lateral Thrust @ 125 MPH NA
Bending Moment @ 125
MPH
NA
Height 17.5 inches (440 mm)
Mounting Base Diameter 1 inch (25 mm)
Weight 0.3 lbs (0.12 kg)
Side View Beam Pattern
Firetide Antenna & Accessories Guide | Version 4.0 | October 2014 Page 11.
Order Number
4000-1111
Page 12.
Firetide A0-050-MIMO-9 Omnidirectional Antenna
The Firetide A0-050-MIMO-9 omnidirectional antenna is
designed to provide maximum performance and reliability
under the toughest weather conditions. The antenna features
a UV-stable, vented radome that provides ultimate protection
against weather elements. This antenna can be can be mast or
ceiling mounted.
Benefits:
•Vented system design. Provides reliable performance by
protecting the electrical design against extreme moisture
and/or temperatures.
Thread relief on connector. Improved accessibility for•
taping reduces installation time and improves overall
effectiveness.
Internal o-ring seal in the base of the antenna with•
integrated connector at the base. Assures a watertight seal to
prevent water from migrating into the antenna connector.
Applications:
5 GHz Wlan, Wi-Fi system•
IEEE 802.11a,n•
Three 5 GHz ports•
continued on next page
Electrical Specifications Value
Frequency range 4900 – 6100 MHz
Bandwidth 700 MHz
Gain 8 dBi
BeamwidthE-Plane 17°
H-Plane 360°
Electrical Downtilt 10°
Isolation ≤ 25 dB
VSWR (Voltage Standing Wave Ratio) ≥ 1.8
Impedance 50 Ω
Polarization Vertical
Max. Power 20 W
Mechanical Specifications
Connector Type N-Female
Dimensions Ø145 mm x 200 mm
Weight 2 Kg
Pole Diameter Ø40 mm – Ø70 mm
5 GHz E-Plane
5 GHz H-Plane
Order Number
AO-050-MIMO-9
Firetide Antenna & Accessories Guide | Version 4.0 | October 2014
Page 13.
Firetide A0-050-MIMO-9 Omnidirectional Antenna
Antenna
"L" type bracket
Mast
(supplied
by customer)
600 mm
145 mm
145 mm
600 mm
continued from previous page
Firetide Antenna & Accessories Guide | Version 4.0 | October 2014
Page 14.
Firetide AO-050-N Antenna
The Firetide AO-050-N antenna is a 12 dBi omnidirectional
antenna designed to provide maximum performance and
reliability under the toughest weather conditions. This antenna
features a UV-stable that provides ultimate protection against
weather elements. They can be mast or ceiling mounted.
Features and Benefits:
Vented system design. Provides reliable performance by•
protecting the electrical design against extreme moisture
and/or temperatures.
Down-tilt Mast mount kit reduces installation time and•
improves overall effectiveness.
Internal o-ring seal in the base of the antenna with•
integrated connector at the base. Assures a watertight
seal to prevent water from migrating into the antenna
connector.
Applications:
5.1/5.5/5.8 GHz WLAN System•
5.8GHz UNII/ISM System•
WiFi Systems•
Multipoint Applications•
Features:
5.1/5.5/5.8GHz Tri-band•
High Gain, Low VSWR•
Supplied With a Down-tilt Mast Mount Kit•
continued on next page
Electrical Specifications Value
Frequency Range 5150—5850 MHz
Bandwidth 700 MHz
Gain 12 dBi
Beamwidth E-Plane 10°
H-Plane 360°
VSWR (Voltage Standing Wave Ratio) ≥ 2.0
Impedance 50 Ω
Polarization Vertical
Max. Power 100 W
Mechanical Specifications
Connector Type N-Female or N-Male
Dimensions Ø25 mm x 600 mm
Weight 550 g
Pole Diameter ≤ Ø60 mm
E-Plane
H-Plane
Order Number
AO-050-N
Firetide Antenna & Accessories Guide | Version 4.0 | October 2014
Page 15.
Firetide AO-050-N Antenna
continued from previous page
Antenna
Connector
Mast
≤60 mm diameter
(supplied by customer)
Splint & Hose Clamp
20 mm
570 mm
Firetide Antenna & Accessories Guide | Version 4.0 | October 2014
Page 16.
The Firetide AP-050-N is a directional panel antenna with
wide spectrum coverage that provides a cost effective
solution for high volume deployments. With an aluminum
frame and ploycarbonate radome, it is rugged and highly sun
and weather resistant, with an expected service life in excess
of ten years.
It is aesthetic; its small and unobstrusive profile blends
easily with any environment. DC grounding for lightning
protection helps to meet local building codes.
Applications
5.1/5.5/5.8GHz WLAN
•
Wireless Access systems•
5.8 GHz ISM applications•
IEEE802.11a,g
•
WiFi•
Wireless Bridges•
Client Antenna•
Features
5.1/5.5/5.8 GHz Tri-band•
High gain•
Low profile•
Light weight•
All weather operation•
DC Ground for lightning protection•
Supplied with a tilt and swivel mast mount kit•
continued on next page
Firetide AP-050-N Antenna
Electrical Specifications Value
Frequency Range 4900–5875 MHz
Gain ≥ 23 dBi
Beamwidth E: 11°
V: 11°
VSWR (Voltage Standing Wave Ratio) ≤ 1.5
Impedance 50 Ω
Polarization Vertical or Horizontal
Max. Power 50 W
Mechanical Specifications
Connector Type N-Female
Dimensions 306x306x25 mm
Weight 1.4 Kg (with brackets)
Color White
Mounting Pole
Order Number
AP-050-N
E-Plane
H-Plane
Firetide Antenna & Accessories Guide | Version 4.0 | October 2014
Page 17.
continued from previous page
Firetide AP-050-N Antenna
Firetide Antenna & Accessories Guide | Version 4.0 | October 2014
Page 18.
Firetide AP20-050-MIMO-19 Antenna
AP20-050-MIMO-19 is a 19 dBi panel antenna that is best
suited to 5 GHz deployments making it an ideal candidate for
the large city-wide and other video surveillance applications.
This low-profile antenna features rugged design with UV-
coated Aluminum alloy and withstands the challenging
outdoor conditions easily.
Applications
5.8 GHz WLAN system•
5.8 GHz UNII/ISM system•
Point to point, or point to multipoint•
Features
Broad band. 5.1/5.5/5.8/6.1 GHz•
Triple polarization•
MIMO application•
High gain, Low VSWR•
Strong corrosion resistance ability•
continued on next page
Electrical Specifications Value
Frequency Range 4900—6100 MHz
Bandwidth 975 MHz
Gain Vertical 19 dBi
Dual Slant 16 dBi
Horizontal Beamwidth Vertical 22°
Dual Slant 20°
Vertical Beamwidth Vertical 14°
Dual Slant 19°
F/B Ratio ≥ 25 dB
Isolation ≥ 25 dB
VSWR (Voltage Standing Wave Ratio) ≤ 1.8
Impedance 50 Ω
Polarization ±45° and Vertical
Max. Power 10 W
Mechanical Specifications
Connector Type 3XN-type Female
Dimensions 305x305x12 mm
Weight 0.8 Kg (w/o clamps)
Mounting Pole
Order Number
AP20-050-MIMO-19
E-Plane
H-Plane
Firetide Antenna & Accessories Guide | Version 4.0 | October 2014
Page 19.
Firetide AP20-050-MIMO-19 Antenna
continued from previous page
Firetide Antenna & Accessories Guide | Version 4.0 | October 2014
This manual suits for next models
4
Table of contents
