Unical 16,5 Operation instructions

.it
USER OPERATING INSTRUCTIONS
16,5 - 16,5 C

3
Dear Customer,
ank you for having chosen one of our products, the result of many years of experience and of an ongoing
quest for higher quality in terms of safety, reliability and performance.
In this manual, you will nd all the information and useful advice to be able to use your product in the utmost
safety and eciency.
We remind you that the appliance must be commissioned by our Author-
ised Service Centre (Law 37/2008) which will check the installation and ll
out the warranty.
!
• Incorrect installation, maintenance that is not performed properly, and improper use of the product relieves
the manufacturer from any possible damage resulting from use of the stove.
• e appliance must not be used as an incinerator nor must fuel other than pellets be used.
• is manual has been draed by the manufacturer and is an integral part of the product. It must remain with
it during its entire lifetime. Should the product be sold or transferred, always make sure that the booklet is
present as the information it contains is addressed to the purchaser and to all those involved in its installa-
tion, use and maintenance.
• Read the instructions and technical information in this manual carefully before proceeding with installation,
use or any intervention on the product.
• Abiding by the indications provided in this manual guarantees your own safety and that of the product, as well
as working economy and a longer operational life.
• e careful designing and risk analysis performed by our company have produced a safe product. Nonethe-
less, before performing any type of operation, it is recommended to scrupulously comply with the instruc-
tions provided in this document and to always have it on hand.
• Pay the utmost attention when handling ceramic parts, where present.
• Check that the oor where the product is installed is perfectly level.
• e wall where the product is placed must not be made of wood or ammable material. e safety distances
must be maintained.
• While operating, some parts of the stove (door, handle, sides) can reach high temperatures. erefore pay
close attention and use the due precautions especially in the presence of children, elderly, disabled and ani-
mals.
• e stove must be installed by authorised personnel (Authorised Service Centre).
• Diagrams and drawings are supplied as examples; in an eort to pursue a policy of constant development and
renewal of the product, the manufacturer may perform the modications considered appropriate without
any prior notice.
• It is recommended to wear gloves when the stove is at its maximum power output to touch the pellet loading
door and the handle to open door.
• Do not install the stove in bedrooms.
Never cover the body of the stove in any way or obstruct the slits at the top
when the appliance is running. All of our stoves have been tested with in-
line ignition.
In case of a re, disconnect electric power, use an approved re extinguisher and, if needed, call the Fire Bri-
gade. en contact the Authorised Service Centre.
!

4
1.0 Standards and declaration of conformity
Our company declares that the stove complies with the following standards for the European Directive CE
marking.
• 89/336/EEC and 2004/108/EC (EMC directive) and subsequent amendments;
• 2006/95/EC (low voltage directive) and subsequent amendments.;
• 2006/42/EC (machinery directive);
• 89/106/EC (construction products);
• For installation in Italy, refer to UNI 10683/98 or subsequent amendments. e installer of the heating system
must issue the declaration of conformity according to L. 37/2008. All local and national laws and European
standards must be met when installing the appliance;
• EN 60335-1; EN 50165; EN 50366; EN 55014-1; EN 61000-3-2; EN 61000-3-3; EN 14785.
1.1 Information regarding safety
Please read this use and maintenance manual carefully before installing and activating the stove!
If you need explanations, contact your dealer or the Authorised Service Centre.
• e pellet stove must only be operated in domestic environments. is stove is controlled by a circuit board
making combustion fully automatic and controlled; the control unit regulates the ignition phase, 5 output
levels and the extinction phase, guaranteeing safe operation of the stove;
• e basket used for combustion allows most of the ashes produced by burnt pellets to drop into the ash pan.
Nonetheless, check the basket daily as not all pellets have high quality standards (use only quality pellets rec-
ommended by the manufacturer);
• e glass is equipped with a special air pass for self-cleaning. However, it is not possible to avoid a light grey
coating on the glass aer a few hours of work. is also depends on the type of pellet used. Some pellets soil
more than others.
1.2 Liability
With the delivery of this manual, we decline any civil or penal liability for accidents resulting from partial or
total failure to comply with the instructions contained herein.
We decline all liability resulting from improper use of the stove, from incorrect use by the user, from unauthor-
ised changes and/or repairs, from the use of non-original spare parts for this model.
e manufacturer declines any direct or indirect civil or penal liability due to:
• Lack of maintenance;
• Failure to comply with the instructions in the manual;
• Use which does not comply with safety directives;
• Installation which does not comply with the standards in force in the country;
• Installation by unqualied and untrained personnel;
• Changes and repairs not authorised by the manufacturer;
• Use of non-original spare parts;
• Events out of the ordinary.
!
• e stove must only be supplied with quality pellets with a 6 mm diameter, the
type recommended by the manufacturer;
• Before connecting the stove electrically, installation of the exhaust pipes with
the ue must be completed;
• e protective grate inside the pellet tank must never be removed;
• e environment where the stove is installed must have sucient air exchange;
• Never open the oven door while it is operating;

5
• When the stove is running, the surfaces, glass, handle and pipes become
very hot: they must only be touched with adequate protection;
• Keep/preserve the pellets in dry and moisture free rooms;
• Keep both the fuel and any ammable material at an adequate safety dis-
tance from the stove.
2.0 Function keys and display
Function keys
1. Increase temperature
e button allows you to increase the temperature from a minimum of 7°C to a maximum of 40°C.
2. Decrease temperature
e button allows you to decrease the temperature from a maximum of 40°C to a minimum of 7°C.
3. Setting button
Press the button to access the stove programming menu.
4. ON/OFF
Press the key for 2 seconds: the stove switches on or o.
5. Decrease output
e button allows you to decrease the output from a maximum of 5 to a minimum of 1.
6. Increase output
e button allows you to increase the output from a minimum of 1 to a maximum of 5.
SET
!
2.1 Display indications
7. Chronothermostat LED
Indicates that the weekly and/or daily programming is active.
8. “Smoke discharge” stove functioning LED
is is on when the stove is running.
9-10. Upper/lower display
Dierent stove operating modes are viewed on the display, as well as the temperature and work output set by
the user.
Should the stove malfunction, the display shows the relative error message (see paragraph “Particular cases”).
11. Remote control receiver
Reception sensor of commands given by remote control.
12. “Menu” setting LED
e LED ashes when the desired temperature is set.

6
13. Temperature LED
It switches on when the set temperature is reached. ECO appears on the display.
14. Remote control reception LED
e LED ashes when the remote control is used to change the temperature and/or output.
15. “Pellet” LED
e LED ashes whenever pellets are being loaded into the stove.
Function keys
1. Increase temperature
2. Decrease temperature
3. Menu setting
4. ON/OFF
5. Decrease output
6. Increase output
Display indications
7. Chronothermostat LED
8. Stove operating LED
9. Upper display
10. Lower display
11. Remote control receiver
12. “Menu” setting LED
13. Temperature LED
14. Remote control reception LED
15. Pellet LED
1
2
3
7
8
9
10
11
15
14
13
12 45
6
Remote control
1. Increase temperature
2. Decrease temperature
3. Increase output
4. Decrease output
2.2 Description of remote control (optional)
e remote control allows you to control the following
functions:
1. Increase temperature:
Pressing the button increases the temperature
from a minimum of 7°C to a maximum of 40°C.
2. Decrease temperature:
Pressing the button decreases the temperature
from a maximum of 40°C to a minimum of 7°C.
3. Increase output:
Pressing the button increases the output from a
minimum of 1 to a maximum of 5.
+
+
�
�
1
2
3
2
4
Fig. 1
Fig. 2

7
We remind you that the appliance must be commissioned by our qualied
Authorised Service Centre (Law 37/2008), which will check installation and
ll out the warranty.
When commissioning the stove, the room must be well-ventilated as un-
pleasant smells could develop coming from paint and grease in the tube and
shell.
!
4. Decrease output:
Pressing the button decreases the output from a maximum of 5 to a minimum of 1.
5. Switching stove on and o
Press the keys and simultaneously to switch the stove on or o.
�+
2.3 Recommendations
• Do not light the stove intermittently: this could cause sparks which shorten the lifetime of the electric com-
ponents;
• Do not touch the stove with wet hands: the electric components of the stove could cause discharges if handled
improperly. Only authorised technicians can deal with possible problems;
• Do not remove any screw from the rebox without rst having lubricated it;
• Never open the door when the pellet stove is operating;
• Make sure that the brazier basket is positioned correctly.
• All sections of the ue gas pipe must be able to be inspected. If xed, it must have inspection openings for
cleaning.
2.4 Loading pellets into tank
Pellets are loaded into the tank through the specic door at the back of the stove.
To load pellets, act as follows:
• Open the door at the top;
• Pour the desired amount of pellets into the tank, with due care (pour enough pellets to guarantee sucient
stove autonomy);
• Close the door.
3.0 Commissioning the stove
3.1 Stove ignition
• Fill the tank up 3/4 with the type of pellets recommended by the manufacturer;
• Connect the stove to a socket using the supplied cable;
• Press the switch at the back of the stove;
• e upper display will read “OFF” and the lower one, the current time;
• Press the key for 2 seconds. Aer a few seconds, the ue gas extractor fan and the ignition resistance
switch on and the text “FAN ACC” appears;
• Aer about 1 minute, the text “LOAD WOOD” appears, the stove loads the pellets and continues lighting the
resistance;
• When the proper temperature is reached, the display will read “FIRE ON”: this means that the stove has
moved to the last ignition phase at the end of which it will be fully operational;

8
ATTENTION!
Before ignition, a bit of smoke could ll the combustion chamber.
!
3.2 Stove extinction
To switch o the stove, press the key until the display reads “OFF”. Even aer extinction of the stove, the
ue gas extractor fan will continue running for a preset amount of time to guarantee quick exhaust of the ue
gas from the combustion chamber.
4.1 Programming stove - chronothermostat (optional)
is function allows you to program two ignitions and two extinctions of the stove during the day or to pro-
gram it weekly.
To enter programming:
• Press the key SET twice;
• Select the submenus (UT) using the keys and .
UT01: Setting current day and switching chronothermostat o.
If the parameter UT01 is set with the current day, for example Sunday (Day 7), select the day of the week to
which to associate PROGRAM 1 and/or PROGRAM 2 ignition.
Change output
It can be changed while the stove is working from a minimum of 1 and a maximum of 5. Press the button
to increase the value and the button to decrease it. e display indicates the output value.
Change temperature
e user can change the temperature at any time. To change the temperature, rst press SET and then press
or and select the desired value, which will appear on the lower display.
• Aer a few minutes, the upper display will read “ON 1-2-3-4-5” according to the output set, while the lower
display will show the room temperature;
• When the set temperature is reached, the upper display will read: “ECO” while the detected room temperature
will appear on the lower display;
• e temperature LED switches on when the set temperature is reached;
• Before lighting the stove, make sure that the brazier is clear of pellets and clean from residues of previous
combustion. Otherwise empty and clean it;
ATTENTION:
the brazier must be cleaned daily and the ash pan periodically. Reduced
or lack of cleaning can cause the stove to fail to ignite, damaging the stove
and the environment (possible emissions of non-combusted material and
soot).
Do not put pellets back into the brazier when they did not light.
!
4.0 Adjusting the stove

9
4.2 Programming the stove
Pressing the keys and allows you to select the desired value.
ATTENTION!
Switching on the chronothermostat while the stove is running stops the
digital clock inside the stove during the whole time operations in the
menu are carried out. It is recommended to act on the chronothermostat
menu while the stove is in standby (OFF).
!
UT02: Setting time.
Pressing the key again displays the text UT02 and the lower display views the current hour with ashing
dots. Adjust the hour by acting on the keys and .
UT03: Pressing the key again displays the text UT03 and the lower display views the minutes with ash-
ing dots. Adjust the minutes by acting on the keys and .
UT04: Reserved for Authorised Service Centre.
Pressing the key SET again displays the text UT04 reserved for the technician.
Do not modify the set parameters. Modications aer an improper access require the intervention of an au-
thorised technician NOT COVERED BY WARRANTY.
UT05: Indicates the time PROGRAM “1” starts. e time can be changed at 10 minute intervals by acting on
the keys and .
N.B.: is parameter is only enabled if UT01 was previously set other than “OFF”.
UT06: Indicates the time PROGRAM “1” nishes. e time can be changed at 10 minute intervals by acting on
the keys and .
N.B.: is parameter is only enabled if UT01 was previously set other than “OFF”.
UT07:
Allows you to select the day of the week to which to combine PROGRAM “1”.
Press the button to select the day of the week. Press the button to activate/deactivate stove igni-
tion. In the example, the stove is lit on Saturday and Sunday.
SET
SET
Text Meaning
Day 1 Monday
Day 2 Tuesday
Day 3 Wednesday
Day 4 ursday
Day 5 Friday
Day 6 Saturday
Day 7 Sunday
OFF Chronothermostat o
Day 1 Day 2 Day 3 Day 4 Day 5 Day 6 Day 7
Monday Tuesday Wednesday ursday Friday Saturday Sunday
O 1 O 2 O 3 O 4 O 5 On On

10
EXAMPLE
Today is Monday. I want to switch the stove on automatically Monday, Tuesday, ursday and Sunday at 8:00
in the morning and switch it o at 16:00. Wednesday, Friday and Saturday I want to switch it on at 9:00 and
switch it o at 23:00.
ATTENTION!
When programs 1 and 2 have been set, the Timer LED is on. e Timer
LED remains o if programs 1 and 2 have not been set. If electric power
fails, a buer battery switches on, leaving the programmed time settings
unchanged.
!
e program will be as follows:
UT 01: day 1
UT 02: current hour
UT 03: current minutes
UT 04: reserved for technicians and installers
UT 05: 8:00
UT 06: 16:00
UT 07: On1-On2-O3-On4-O5-O6-On7
UT 08: 9:00
UT 09: 23:00
UT 10: O1-O2-0n3-O4-On5-On6-O 7
ATTENTION!
e temperature and output at which the stove operates during the time
periods with programming ON will be those of the last extinction.
!
5.0 Information on display
“OFF”
“OFF” the stove is o or in the extinction phase. E.g: current time 14:30.
UT08:
Indicates the time PROGRAM “2” starts. e time can be changed at 10 minute intervals by acting on the
keys and .
N.B.: is parameter is only enabled if UT01 was previously set other than “OFF”.
UT09: Indicates the time PROGRAM “2” nishes. e time can be changed at 10 minute intervals by acting on
the keys and .
N.B.: is parameter is only enabled if UT01 was previously set other than “OFF”.
UT10: Allows you to select the day of the week to which to combine PROGRAM “2”.
Press the button to select the day of the week. Press the button to activate/deactivate stove igni-
tion.