UniPOS FS5200R User manual

UniPOS Repeater FS5200R
Instruction Manual Page1
Revision 3/01.17 of 48
REPEATER FS5200R
OPERATION MANUAL

UniPOS Repeater FS5200R
Instruction Manual Page 2
Revision 3/01.17 of 48
CONTENTS
1. Introduction........................................................................................................................3
2. Function.............................................................................................................................3
3. Technical data....................................................................................................................3
4. Contents of delivery ...........................................................................................................4
5. General information ...........................................................................................................5
6. Duty Mode .........................................................................................................................9
7. Fire condition...................................................................................................................10
8. Fault Condition.................................................................................................................13
9. Disabled Component........................................................................................................17
10. Information and Control Mode........................................................................................19
11. Labour protection requirements......................................................................................35
12. Installation......................................................................................................................36
13. Repeater start up...........................................................................................................41
14. Conditions of operation, storage and transportation.......................................................42
15. Warranty........................................................................................................................42
16. Appendix 1.....................................................................................................................43

UniPOS Repeater FS5200R
Instruction Manual Page 3
Revision 3/01.17 of 48
1. Introduction
Repeater FS5200R is a unit supplementing the range of 5000 series products expanding the
possibilities of the fire detecting and fire extinguishing systems built on the basis of fire control
panels FS5100, FS5200, FS5200E and FS4000.
Some of its main features and possibilities are:
Indicates Fire condition and/or Fault condition occurred in each of the fire control panels
connected to it;
control effect on the connected fire control panels that have sent a signal for Fire
condition;
user oriented menu dialogue for easy and convenient operation;
four-line LCD for visualization the different modes of the repeater;
LEDs and sound indication of the operation modes;
user oriented test modes allowing for a total control of the site protected;
energy independent archive memory saving the event type, date and time,;
2. Function
Repeater FS5200R:
- receives data for Fire condition from the remote fire control panels:
- receives data for Fault condition from the remote fire control panels:
- displays information for the condition of remote fire control panels;
- executes control commands to lines of remote fire control panels for their forced exit of Fire
condition;
Repeater FS5200R could be used:
- when the persons whom are expected to detect and react initially to the fire condition
and/or fault condition signals are at a different place from the location of the fire control
panel/s;
- when fire control panels located at different sites have to be monitored and controlled
from one place;
- when the fire control panel/s are monitored from several locations.
It is compatible with FS4000, FS 5100, FS 5200, FS 5200E and FS5200R.
3. Technical data
3.1. Functional characteristics
-Connection of maximum 15 remote fire control panels (repeaters) to one
repeater;
Built-in sounder for fire condition –one tonal, discontinuous, can be switched
off
Built-in sounder for fault condition –one tonal, discontinuous, can be switched
off

UniPOS Repeater FS5200R
Instruction Manual Page 4
Revision 3/01.17 of 48
Built-in real time clock
-Interfaces for communication with the fire control panels RS485 connected to it;
-Option to prolong the time period for Fire condition stage I with programmable
inspection period
-Possibility for delay when switching the outputs for Fire alarm;
-Energy independent archive –up to 100 events;
-Operation with a wide range of output devices;
3.2. Indications of registered events
-Light indication –LED
-Text messages –LCD display, 4 lines 20 characters per line, Cyrillic letters
-Sound signaling –built-in sounder
3.3. Monitored outputs
type –potential
electrical characteristics - (245)V DC / 1A
3.4. Relay output for general function
type –potential free, switching
electrical characteristics –3A/125ADC; 3A/30VDC
3.5. Relay output for fault condition
type –potential free, switching
electrical characteristics –3A/125ADC; 3A/30VDC
3.6. Power supply
3.6.1. Mains
voltage –220/230 VAC
frequency –50 Hz
3.6.2. Back up batteries
battery type –lead, gel electrolyte
number of batteries –2 pcs
connection –consecutive
nominal voltage of the connected back up batteries –24 V DC
nominal capacity С20 –(1,2 –4,5) Ah
extreme discharge voltage –17,6V
charge voltage –28V
3.6.3. Fuses
mains 220/230 V –4,0 А
back up batteries –2,0 А
3.7. Dimensions and weight of the unit
dimensions –313 х 218 х 85 mm
weight (batteries not included) –1,6 kg
4. Contents of delivery
Repeater FS5200R - 1 pc
Resistor 5,6 k- 2 pcs
Jumper for backup batteries - 1 pc

UniPOS Repeater FS5200R
Instruction Manual Page 5
Revision 3/01.17 of 48
Fuse 4А - 1 pc
Fuse 2А - 1 pc
Instruction manual - 1 pc
Instructions for authorized staff - 1 pc
Packing - 1 pc
5. General information
5.1. Access levels
Four access levels are available in the repeater:
5.1.1. Access Levels 1 and 2
All persons who would presumably find out and react to alarm upon fault condition or fire
condition have access to level 1 and 2. They shall be trained and authorized to operate the
repeater in the following conditions: Duty Mode, Fault condition; Disabled component and
System functions (except SetUp).
The following actions are accessible:
Displaying suppressed messages for Fire condition, Fault condition, Disabled
components and Zone in test
Forced proceeding from phase Fire condition stage I to phase Fire condition stage II
Suppressing the local sounder
Displaying the status of the connected fire control panels and repeaters;
Switching off the outputs, activated upon fire condition;
Exit of Fire condition; SetUp Mode
System functions of the fire control panel, except
5.1.2. Access Level 3
To access this level:
-unlock and open the front cover of the repeater;
-enter a password.
For the personnel authorized to have Access Level 3, it is available
-all features accessible at Level 1 and 2;
-reconfiguration of specific data of the repeater;
-replacing a burnt fuse;
-connecting executive devices;
-connecting slave fire control panels and repeaters;
-maintenance of the repeater.
5.1.3. Access Level 4
Accessible for personnel trained and authorized by the Producer to repair the repeater and to
modify the software
5.2. Conditions and indication
The repeater FS5200R operates in six basic modes: Duty Mode, Fire Condition, Fault
Condition, Disabled Component Mode, Information and Control Mode and SetUp Mode:

UniPOS Repeater FS5200R
Instruction Manual Page 6
Revision 3/01.17 of 48
Duty Mode - the repeater is in Duty Mode, when the fire control panels connected to it are
not in any of the rest five possible conditions and they have a connection with ;
Fire condition –The repeater enters Fire condition when a fire detector is activated in a
line/lines of the fire control panel connected to it;
Fault condition –the repeater enters this condition when a fault in any of the fire control
panels connected to it is registered or its connection with any of the fire control panels has
been interrupted;
Disabled component - the repeater enters Disabled component after a manual operation,
disabling a certain component has been performed –monitored output;
Information and Control;
SetUp Mode –the repeater enters SetUp Mode after activation of submenu Set up, in
Information and Control Mode;
In any moment the repeater can be in any of the above conditions/modes, or in a random
combination of Fire condition, Fault condition, Disabled component and Information and Control
mode. Duty Mode and SetUp Mode can not be combined with another mode:
the repeater enters Duty Mode after all other conditions are exited;
when the repeater enters SetUp Mode it exits all other conditions.
The conditions of the repeater and their corresponding indication are shown in Table 1.
Conditions of the repeater
Indication
All conditions -
The repeater is power supplied
- indicator Power supply –
continuous green light [12]
- indicator for inspection time (if
programmed) [13]
Fire condition
- common indicator Fire condition -
red light; [19]
- individual LED indicator for the
slave fire control panel (repeater)
[21]
- indicator for inspection time (if
programmed) [13]
- indicator Power supply –
continuous green light [12
Fault condition -
All faults except for Battery Low
- Common indicator Fault condition
–continuous yellow light [1]
- Fault condition in a remote fire
control panel [4]
Fault condition –System error
Indicator System error –
continuous yellow light [2]
Fault condition
Indicator Fault in mains supply of
the remote fire control panel -
continuous yellow light [5]
Fault condition
Common indicator Fault in fire
detecting line of a remote fire
control panel - continuous yellow
light [6]

UniPOS Repeater FS5200R
Instruction Manual Page 7
Revision 3/01.17 of 48
Conditions of the repeater
Indication
Fault condition
Indicator Fault in monitored output
of a remote fire control panel
- continuous yellow light [7]
Fire condition
Local sounder –discontinuous signal: 0.5 s
sound, followed by 0.5s break
Fault condition –
All faults except for Battery Low
Local sounder –discontinuous signal: 1 s
sound, followed by 1 s break
Fault condition -
Low battery
Local sounder –discontinuous signal: 1 s
sound, followed by 3 s break
5.3. Means of control and indication
Means of control
Condition of the repeater
operation
Button Reset
Fire condition
Control operation, to force a line of the
remote fire control panel to exit Fire
condition (reset line) [14]
Button Menu
Duty mode, Fault condition
Information and Control
mode, SetUp mode and Fault
condition
To enter the menu for review, setting up
the repeater [8]
Button Down
Duty mode, Fault condition
Information and Control
mode, SetUp mode and Fault
condition
To display in the text screens the next
message or element of the menu [9]
Button Up
Duty mode, Fault condition
Information and Control
mode, SetUp mode and Fault
condition
To display in the text screens the next
message or element of the menu [10]
Button Exit
Duty mode, Fault condition
Information and Control
mode, SetUp mode and Fault
condition
To exit the menus or to exit SetUp mode
with saving the changes [11]
Button Alarm
Fault condition, Fire condition
To suppress the local sounder [15]
Button Outputs
Fire condition
- Upon activated outputs for fire condition
–to suppress the outputs;
- If no outputs for fire condition are
activated –to activate the suppressed
outputs, if any [17]

UniPOS Repeater FS5200R
Instruction Manual Page 8
Revision 3/01.17 of 48
5.4. Panel for control and indication
LED indicators and buttons are positioned in functional groups, as follows:
Indicators for common fault conditions - [1], [2] and [3];
Indicators for fault conditions in the remote fire control panels (repeaters) –[4], [5], [6]
and [7];
Buttons for control on the LCD display and for entering of parameters –[8], [9], [10]
and [11];
Individual indicators for Fire condition and Fault condition of remote fire control
panels –[21];
Buttons and indicators showing each status of the repeater –[12], [13], [14], [15],
[16], [17], [18] and [19].
1 2 345 6 78 9 10 11 12 13 14 15
1
2
3
4
5
6
7
8 9 10 11 21
13
14
15
16
17
18
19
20
12
Front panel of repeater FS5200R
1 Common indicator for Fault condition
2 Indicator for System error
3 Indicator for Fault in power supply
4 Common indicator for Fault condition in a remote fire control panel
5 Common indicator for Fault in power supply in a remote fire control panel
6 Common indicator for Fault condition in fire detecting line of a remote fire control panel
7 Common indicator for Fault condition in monitored output of a remote fire control panel
8 Buttons Menu
9 Button Down

UniPOS Repeater FS5200R
Instruction Manual Page 9
Revision 3/01.17 of 48
10 Button Up
11 Button Cancel
12 Indicator Power supply
13 Indicator Delay of the outputs for Fire condition of the repeater
14 Button Reset
15 Button Alarm with indicator Suppressed alarm
16 Indicator Suppressed alarm
17 Button Outputs with indicator Suppressed outputs
18 Indicator Suppressed outputs
19 Indicator for Fire stage
20 LCD display (4х20)
21 Individual indicators for Fire condition and Fault condition in the remote fire control
panels.
6. Duty Mode
6.1. Description
The repeater is in Duty Mode when:
-it is not in Fault condition;
-the connected to it remote fire control panels (repeaters) are not in Fire
condition or Fault condition.
6.2. Indication
6.2.1. LED and sound indication
In Duty Mode the green LED indicator (Power supply) and the indicator upon
programmed inspection time of the outputs are activated.
6.2.2. Text message
The display shows:
a message “Fire protect”,
i.e. the fire control panel
is in Duty Mode;
the current local time;
the day of the week;
the current date.
12345678910 11 12 13 14 15
6.2.3. Using the keypad
For all access levels the only active button in Duty Mode is (Menu). Press it and the
repeater enters System Functions status.

UniPOS Repeater FS5200R
Instruction Manual Page 10
Revision 3/01.17 of 48
7. Fire condition
7.1. Description
The repeater enters Fire condition after a fire condition has been activated in any of the
fire control panels or repeaters connected to it.
To exit this condition press button and the line in fire condition shown in the upper field of
the display is reset (section.7.3.3).
7.2. Indication
7.2.1. LED and sound indication
In this condition the following indicators
illuminate:
indicator (Fire) in red light;
the individual indicator for Fire
condition of a remote fire control
panel illuminates in red light;
if the outputs of the repeater for
phase Fire condition are
suppressed by button
(Outputs), the LED indicator of
the button illuminates in
continuous red light;
12345678910 11 12 13 14 15
if the sound signaling is suppressed by button (Alarm), “Аларма”), the LED
indicator of the button illuminates in continuous red light.
7.2.2. Text messages
For this condition the display is
divided into two text field:
the first field displays
information about the first
fire control panel and line
in fire condition;
the second field is used
to show information if
more than one fire control
panel (line) is in fire
condition.
If more than 2 lines are in fire
condition, use the buttons
(down) and (up) to view all lines
01 Fire s1/RP01/Ln02
Remote panel 01
03 Fire s2/RM01/Ln05
Remote panel 02
Serial
number of
the fire
Fire stage:
- Fire stage 1
- Fire stage 2
Remote panel
Line in Fire
(subject of reset)
Name remote
panel
First text field
Second text field
Line in Fire
Upon registration of more than 2 fire conditions,
the display visualizes continuous information about