Unitone 3000F User manual

User Manual For Video Intercom System 3000F rev.10. 03-28-16 Page 1
USER MANUAL
FOR
VIDEO INTERCOM SYSTEM 3000F

User Manual For Video Intercom System 3000F rev.10. 03-28-16 Page 2
TABLE OF CONTENTS
Title Page Number
Placing A Call From The Building Call Panel………………………………..3
Receiving Calls From The Building Call Panel……………………………..4
Additional Views From The Cameras…………………………………………..4
Messages From The Building Management…………………………………..4
Intrusion Alarm System………………………………………………………………..5
a) Setting or Changing The Security Code
b) Intrusion Alarm –Home Mode
c) Intrusion Alarm –Away Mode
d) Duress Emergency Mode
(Important Notes about Alarm Modes)
Enter The Building Using A Card Reader………………………………………7
Miscellaneous………………………………………………………………………………..7

User Manual For Video Intercom System 3000F rev.10. 03-28-16 Page 3
1. Placing A Call From The Building Call Panel
Scroll thru the tenant/apartment list, using the “A” or “Z” buttons.
Once, desired entry is found-press “Call” button.
If 4-digit apartment code is known, dial it in and press the call button.
Use “*” to stop the call or erase dialed number.
HOW TO USE YOUR UNITONE 3000F
APARTMENT VIDEO UNIT:

User Manual For Video Intercom System 3000F rev.10. 03-28-16 Page 4
2. Receiving Calls From The Building Call Panel
You will hear a chime, and see a view of the visitor on your monitor. You can either:
Ignore the call… the visitor will not know if you are home. or
Press the “talk” button once and talk to the visitor.
After speaking to the visitor, to release the lock and allow the door to be opened,
Press the “Door” button.
After the “Door” button has been pressed, the system will switch from the call panel
camera to the lobby camera so you can watch the visitor enter.
3. Additional Views From The Buildings Cameras (If Installed)
In addition to the Call Panel view, residents can obtain three additional views from
other cameras by pressing any one of the three “eye lid” view buttons.
NOTE: If the view is interrupted, a flashing yellow light will indicate that a
visitor has just called another apartment and therefore has priority with the
camera.
4. Messages From The Building Management
The building management can send messages to individual apartments or to a group
of apartments. If the green LED indicator next to the “Message” button is
blinking, press the “Message” button to see the first message.
Press the “Door”button to delete the message.

User Manual For Video Intercom System 3000F rev.10. 03-28-16 Page 5
5. Intrusion Alarm System
A) Setting or Changing the Security Code
To change the security code - call the concierge from the apartment unit and
remain on the line.
While on call, request concierge or superintendant to initiate procedure to
change the security code.
A single tone sounds from the apartment unit indicating the reset function is
activated.
Enter a new 4-digit security code on the apartment unit keypad.
A tone sounds each time a number on the keypad is pressed indicating it was
recognized by the system.
When finished keying the new code, then press Enter.
The resident and concierge may now end the call.
If concierge and/or super is not available call the Building Management
Office and ask to have your code changed.
The security code remains confidential: it is not displayed on the screen or
Written to the system log.
B) Intrusion Alarm - Away Mode*
To Activate:
Make sure the front door is closed.
Press "AWAY" button, the red light will illuminate.
Leave apartment within 30 seconds.
To Deactivate:
Upon your return when you open the door, the unit will beep to remind you to
enter your code. After 30 seconds the local alarm will sound.

User Manual For Video Intercom System 3000F rev.10. 03-28-16 Page 6
(Press your 4-digit code and press "ENTER" button).
The alarm will deactivate and the red light will be turned off.
If someone enters your apartment and does not punch in your code within 30
seconds, your apartment alarm will sound a loud alarm pattern and a signal
will be sent to the main control panel (see note below). The alarm
automatically turns off after a 30 second period. The LED next to the
“AWAY” button will flash, indicating that the alarm was set off.
C) Intrusion Alarm - Home Mode*
Press "HOME" button once and the red light will illuminate.
Should someone break in, your apartment alarm will sound immediately
(there is no 30 second delay) and a signal is sent to the main control cabinet.
(see note below)
To turn off the alarm, press your 4-digit code followed by
“ENTER
Note: Hit cancel if you enter the wrong code.
D) Duress Emergency Mode*
If you are ever forced by someone to enter your apartment, the system
will allow you to discreetly call for help.
When entering your code, add or subtract one digit from the last digit in
your code. For example, if your code is 1234, enter 1233 or 1235.
The Control Cabinet will get a duress signal from your apartment, while your
unit will remain silent as if it were deactivated. (see note below)
*Note: Unless the building management subscribes to a Central Station Monitoring
service, the “Away” and “Intrusion” alarms will ONLY SOUND LOCALLY in your
apartment. Though they provide a powerful deterrent, no one other than your neighbors
may hear the alarm. Without Central Station Monitoring the “Duress” alarm does not
ring anywhere. This function was developed for buildings with either monitoring or a
full time doorman.

User Manual For Video Intercom System 3000F rev.10. 03-28-16 Page 7
7. Enter Building Using Proximity Card Reader (Optional)
Swipe your proximity access card/key fob at the card reader
System will unlock the front door for preset period of time
8. Miscellaneous
The “Call” button is used to call a Super, Doorman or Concierge, if available and on
duty.
Please report problems to the Super or management office. They will contact Unitone
to dispatch a service technician.