Universal Remote ZR-1N Z User manual

Owner’s Manual
ZR-1N Z Repeater

ZR-1N Z Repeater Owner’s Manual ©2010 - 2014 Universal Remote
Control, Inc.
he information in this Owner’s Manual is copyright protected. No part of this
manual may be copied or reproduced in any form without prior written consent
from Universal Remote Control, Inc.
UNIVERSAL REMO E CON ROL, INC. SHALL NO BE LIABLE FOR OPER-
A IONAL, ECHNICAL OR EDI ORIAL ERRORS/OMISSIONS MADE IN
HIS MANUAL.
he information in this Owner’s Manual may be subject to change without prior
notice.
otal Control is a registered trademark of Universal Remote Control, Inc.
URC - Control the Experience is a registered trademark of Universal Remote
Control, Inc.
All other brand or product names are trademarks or registered trademarks
of their respective companies or organizations.
500 Mamaroneck Avenue, Harrison, NY 10528
Phone: [phone] Fax: [phone]

TABLE OFCONTENT
ntroduction 1
Features and Benefits 1
Parts Guide 1
ZR-1N Front and Side Panel Descriptions 2
Specifications 3
Limited Warranty Statement 4
End User Agreement 6
Federal Communication Commission
nterference Statement 7
Regulatory nformation to the user 8
Declaration of Conformity 9

Page 1
ZR-1N Z REPEATER
ntroduction
Congratulations on your purchase of the ZR-1N Z Repeater! The ZR-1N
is used to extend the operational range between Total Control products
such as the TRC-780 and the MRX-10. Once joined to the MRX-10 it
will wirelessly relay communication between an TRC-780 and another
ZR-1N repeater.
Features and Benefits
Wirelessly extends the range between Total Control products. Extend the
operational range between a TRC-780 remote and a MRX-10 Advanced
Network System Controller. Control lighting, music and more from through-
out the home.
Parts Guide
The ZR-1N Z Repeater includes:
1 - ZR-1N Z Repeater 1 - AC Power Adapter
1 - Wall Mount and 4 Screws 1 - Owner’s Manual

Page 2
ZR-1N Z REPEATER
ZR-1N Front and Side Panel Descriptions
The front panel consists of 3 indicator lights which will illuminate
when in use.
Power LED: ndicates that the ZR-1N is powered on when illuminated.
Status LED: The LED will show what the RF signal strength of the
ZR-1N to the MRX-10. By pressing the TEST button on the side of
the unit, it will indicate the signal strength. When the LED is:
. OFF: The ZR-1N is not testing for signal strength, and the TEST
button should be pressed.
. Orange: The signal strength is LOW, and the ZR-1N should be
move to a different location
. Green: The signal strength is GOOD, and the ZR-1N is in a
good location.
Data LED: The LED will flash RED when the unit is transmitting or
receiving data.
Antenna: Omnidirectional antenna. Adjust the antenna for best per-
formance. Usually vertical positioning works well.
DC9V Power: Attach the included 9V DC power supply here.
Mounting Plate: May be attached to a wall or other surface with the
included screws for easy slide on/off mounting.
POWER
LED STATUS LED
USB
DC9V
Power
TEST
Mounting
Plate
Antenna
DATA
LED

Page 3
Specifications
RF Frequency: 2.48GHz (Two-way RF)
Effective Range: Typically 50-75 ft, depending on environment
ize: L x D x H = 3.625" x 1.125" x 6.625" (with antenna vertical)
Weight: 3 oz.
Power upply: 9V DC 300mA
ZR-1N Z REPEATER

Page 4
Limited Warranty Statement
1. Limited Warranty and Disclaimers
Universal Remote Control, nc. (“URC”) warrants that the URC equipment shall
be free from defects in material and workmanship under normal usage for two
(2) years from purchase when such is purchased from URC. This limited
warranty is valid only in the United tates of America. URC warrants that the
software will substantially conform in any material respect to its functional
specifications at the time of delivery. URC SHALL NOT BE L ABLE FOR
OPERAT ONAL, TECHN CAL OR ED TOR AL ERRORS AND/OR
OM SS ONS MADE N THE URC DOCUMENTAT ON. URC DOES NOT
WARRANT THAT THE URC SOFTWARE S BUG-FREE OR ERROR FREE OR
THAT THERE ARE NO ERRORS/BUGS N THE URC SOFTWARE.
URC warrants that at the time of purchase the URC equipment and the URC
software complied with all applicable regulations and policies of the Federal
Communications Commissions (“FCC”) regarding electromagnetic interference
caused by electronic/computing devices and to the extent that the URC
equipment and/or the URC software fails to so comply, URC shall, at its own
expense, take all reasonable measures to promptly cause such to comply.
URC equipment purchases from other than an authorized URC dealer or
distributor are without warranty.
TH S L M TED WARRANTY DOES NOT COVER TECHN CAL ASS STANCE
FOR HARDWARE OR SOFTWARE USAGE EXCEPT AS EXPRESSLY
PROV DED FOR HERE N, THE EQU PMENT, SOFTWARE AND
DOCUMENTAT ON OF URC ARE SUPPL ED “AS S” W THOUT ANY
WARRANTY, EXPRESS, STATUTORY OR MPL ED, OF ANY K ND. TO
THE MAX MUM EXTENT PERM TTED BY APPL CABLE LAW, URC
EXPRESSLY DSCLA MS ALL WARRANT ES, EXPRESS, STATUTORY OR
MPL ED, NCLUD NG BUT NOT LMTED TO THE WARRANT ES OF
MERCHANTAB L TY AND F TNESS FOR A PART CULAR PURPOSE. URC
DOES NOT WARRANT, GUARANTEE, OR MAKE ANY
REPRESENTAT ONS REGARD NG THE USE OF, OR THE RESULTS OF THE
USE OF, THE EQU PMENT, SOFTWARE OR DOCUMENTAT ON N
TERMS OF CORRECTNESS, ACCURACY, REL AB L TY OR OTHERW SE.
EXCEPT AS EXPRESSLY PROV DED FOR HERE N, TECHN CAL SERV CES
ARE SUPPL ED “AS S”, W THOUT ANY WARRANTY, EXPRESS,
STATUTORY OR MPL ED, OF ANY K ND. TO THE MAX MUM EXTENT
PERM TTED BY APPL CABLE LAW, URC EXPRESSLY D SCLA MS ALL
WARRANT ES, EXPRESS, STATUTORY OR MPL ED, NCLUD NG BUT
ZR-1N Z REPEATER

Page 5
ZR-1N Z REPEATER
NOT L M TED TO THE WARRANT ES OF QUAL TY OR REASONABLE
SK LL AND CARE, OR OUTCOME OR RESULTS. WTHOUT N ANY WAY
L M T NG THE GENERAL TY OF THE OTHER PROV S ONS HERE N,
WARRANTY DOES NOT COVER: ( ) DAMAGE FROM M SUSE, NEGLECT
OR ACTS OF NATURE, ( ) MOD F CAT ONS, ( ) NTEGRAT ON W TH
TH RD PARTY CONTENT ( V) BEYOND THE WARRANTY PER OD AND/
OR FA LURE TO FOLLOW URC WARRANTY CLA M PROCEDURE.
The warranty limitations and warranty disclaimers may not apply to end user in
whole or in part, where such are restricted or excluded by applicable law and
such shall apply to the maximum extent permitted by applicable law.
n the event of any warranty claim, URC will, at its sole option, repair the URC
equipment using new or comparable rebuilt parts, or exchange the URC
equipment for new or rebuilt equipment. In the event of a defect, these are the
end user’s exclusive remedies.
All the URC equipment returned for service, exchange or repair require an RGA
number. To obtain an RGA number, you must complete a Return Request
Form which you may obtain by calling [phone] or contacting URC at
[e-mail]. To obtain warranty service, end user must
deliver the URC equipment, freight prepaid, in its original packaging or
packaging affording adequate protection to URC at 420 Columbus Avenue,
Valhalla, NY 10595. t is the end user’s responsibility to backup any macro
programming, artwork, software or other materials that may have been
programmed into the unit. t is likely that such data, software, or other materials
will be lost during service and URC will not be responsible for any such
damage or loss. A dated purchase receipt, bill of sale, installation contract or
other verifiable proof of purchase is required. For the URC equipment support
and other important information, please visit URC's website available at
www.universalremote.com or call the Customer Service Center at (914) 835-
4484.
This limited warranty only covers the URC equipment issues caused by defects
in material or workmanship during ordinary consumer use. t does not cover
product issues caused by any other reason, including but not limited to product
issues due to commercial use, acts of God, third-party installation, misuse,
limitations of technology, or modification of or to any part of the URC
equipment. This limited warranty does not cover the URC equipment sold as
used, as is, refurbished, so called "B stock" or consumables (such as batteries).
This limited warranty is invalid if the factory applied serial number has been
altered or removed from the URC equipment. This limited warranty specifically
excludes the URC equipment sold by unauthorized resellers.
With the exception of URC’s R-only, broad-based consumer remotes, none of

Page 6
ZR-1N Z REPEATER
URC’s PC programmable remotes or any of our Total Control® whole-house
equipment are authorized for online internet sales. Buying URC’s PC
programmable remotes or any of our Total Control® whole-house equipment
online means buying equipment that does not have a URC’s limited warranty.
Such equipment is not eligible for URC tech support or software support, either.
2. URC’ Limitations of Liability
N NO EVENT SHALL URC BE L ABLE FOR ND RECT, SPEC AL,
NC DENTAL, EXEMPLARY, PUN T VE OR CONSEQUENT AL DAMAGES
OF ANY K ND OR LOSS OF PROF TS OR BUS NESS OPPORTUN TY, EVEN
F URC S ADV SED OF THE POSS B L TY OF SUCH DAMAGES.
N NO EVENT SHALL URC BE L ABLE FOR LOSS OF OR DAMAGE TO
DATA, COMPUTER SYSTEMS OR COMPUTER PROGRAMS. URC’S
L AB L TY, F ANY, FOR D RECT DAMAGES OF ANY FORM SHALL BE
L M TED TO ACTUAL DAMAGES, NOT N EXCESS OF AMOUNTS PA D
BY END USER FOR THE URC EQU PMENT.
N NO EVENT SHALL URC BE L ABLE FOR ANY EVENTS BEYOND TS
CONTROL, NCLUD NG ANY NSTANCE OF FORCE MAJEURE.
N NO EVENT SHALL URC BE L ABLE FOR THE ACTS OR OM SS ONS OF
END USER OR ANY TH RD PARTY.
THE L M TAT ONS OF L AB L TY MAY NOT APPLY TO END USER N
WHOLE OR N PART, WHERE SUCH ARE RESTR CTED L M TED OR
EXCLUDED BY APPL CABLE LAW AND SUCH SHALL APPLY TO THE
MAX MUM EXTENT PERM TTED BY APPL CABLE LAW. URC SHALL NOT
BE HELD RESPONS BLE FOR THE STATEMENTS MADE BY OTHERS.
SOME STATES OR JUR SD CT ONS DO NOT ALLOW THE EXCLUS ON OR
L M TAT ON OF NC DENTAL OR CONSEQUENT AL DAMAGES, OR
ALLOW L M TAT ONS ON HOW LONG AN MPL ED WARRANTY LASTS,
SO THE ABOVE LMTAT ONS OR EXCLUS ONS MAY NOT APPLY TO
END USER. TH S L M TED WARRANTY G VES END USER SPEC F C LEGAL
R GHTS AND END USER MAY HAVE OTHER R GHTS WH CH VARY
FROM STATE TO STATE OR JUR SD CT ON TO JUR SD CT ON.
End User Agreement
The terms and conditions of the End User Agreement available at www.uni-
versalremote.com/eua.php shall apply.

ZR-1N Z REPEATER
Federal Communication Commission
nterference Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. f this equipment does cause harmful interference to radio or tele-
vision reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one more of the
following measures:
uReorient or relocate the receiving antenna.
uncrease the separation between the equipment and receiver.
uConnect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
uConsult the dealer or an experienced radio/TV technician for help.
Warning!
Changes or modifications not expressly approved by the manufacturer could
void the user's authority to operate the equipment.
Note : The manufacturer is not responsible for any Radio or TV interference
caused by unauthorized modifications to this equipment. Such modifications
could void the user's authority to operate the equipment.
FCC Caution
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the authority to operate equipment.
The antenna(s) used for this transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Federal Communication Commission (FCC) Radiation Exposure tatement
The device and the antenna for this device must be installed to ensure a
minimum separation distance of 20 cm more from a person's body. Other
operating configurations should be avoided.
Page 7

Page 8
ZR-1N Z REPEATER
Regulatory nformation to the user
nCE conformity Notice
Products with “CE” marking comply with the R&TTE Directive
1995/5/EC, EMC Directive 2004/108/EC and Low Voltage
Directive 2006/95/EEC issued by the commission of the European
Community.
1) R&TTE Directive
lLVD : EN 60950-1
lEMC : ETS EN 301 489-1,3
lRF : ETS EN 300 220-1,2
: ETS EN 300
2) EMC Directive
lEmission : EN 55022
lmmunity : EN 55024
lPower : EN-61000-3-2, 3
Use only with EN60950-1 approved as Limited power source and
double insulation( ) marked power adaptor & same ratings
described on the product label (9DVdc, 300mA).
nDeclaration of Conformity
“Hereby, Universal Remote Control nc. declares that this ZR-1N is in
compliance with the Essential requirements and other relevant provi-
sions of Directive 1999/5/EC.”
Certification
Type No.(Model No.) ZR-1N
Batch/Serial No. -
Power Rating 9.0V , 300mA
Frequency band 2.48GHz

Page 9
Declaration of Conformity
Company Name : Universal Remote Control Inc.
Company Address : 500Mamaroneck Avenue, Harrison, NY 10528, U.S.A
Contact Information : www.universalremote.com
hone: [phone] Fax: [phone]
Brand Name : UNIVERSAL remote control
roduct Name : ZR-1N Z Repeater
Model Name : ZR-1N
This product herewith complies with the requirements of EMC Directive (2004/108/EC)
and R&TTE Directive(1995/5/EC) issued by the Commission of the European Community
Compliance with these directives implies compliance with the standards above
n EMC Directive
l EN 55022
l EN 55024
l EN 61000-3-2
l EN 61000-3-3
n R&TTE Directive
l EN 60950-1
l ETSI EN 301-489-1,3
l ETSI EN 300 220-1,2
l ETSI EN 300
List of test reports and/or certificate verified compliance with the standards above
Date of issue : November 30, 2010
Name and signature of authorized person :
n EMC Directive
l Report No.
l Testing Laboratory : Gumi College EMC Center
n R&TTE Directive
l Certificate No.
l Certificate Body : TUV Rheinland (No. 0197)
James Novak
Senior roduct Manager
Universal Remote Control Inc.
ZR-1N Z REPEATER

Page 10
NOTE

Page 11
NOTE

Page 12
NOTE

OCE-0097B Rev 01
500 Mamaroneck Avenue, Harrison, NY 10528
Phone: [phone] Fax: [phone]
www.universalremote.com