Universal Tool UT8807B Specifications

Manufacturer/Supplier Product Type RPM
Cycles Per Min
Tel No Fax No(01494) 883300 (01494) 883237
Model No/Nos Serial No
Product Nett Weight Recommended Use Of
Balancer Or Support
Recommended Hose Bore
Size - Minimum
Recommended Max
Hose Length
Ins M/M Ft M
Foreseen Use Of Tool
This drill is designed for the purpose of drilling holes in all types of
materials, i.e. metals, wood, stone, plastics etc. using drilling bits
designed for this purpose. It may be used with other forms of cutting
tools, polishing devices or for sanding using coated abrasive products.
Before using any such products first check with the manufacturer their
suitability for use with this type of drill. Do not use bonded abrasive
products (i.e. grinding wheels) or saw blades or any device which has
a permitted safe working speed less than the free speed of the drill.
Do not use this drill for any other purpose than that specified without
consulting the manufacturer or the manufacturer's authorised supplier.
Putting Into Service
Air Supply
Use a clean lubricated air supply that will give a measured air pressure
at the tool of 90 p.s.i./6.3 bar when the tool is running with the trigger
fully depressed. Use recommended hose size and length. It is
recommended that the tool is connected to the air supply as shown
in figure 1. Do not connect the tool to the air line system without
incorporating an easy to reach and operate air shut off valve. The air
supply should be lubricated. It is strongly recommended that an air
filter, regulator, lubricator (FRL) is used as shown in Figure 1 as this will
supply clean, lubricated air at the correct pressure to the tool. Details
of such equipment can be obtained from your supplier. If such
equipment is not used then the tool should be lubricated by shutting
off the air supply to the tool, depressurising the line by pressing the
trigger on the tool. Disconnect the air line and pour into the intake
bushing a teaspoonful (5ml) of a suitable pneumatic motor lubricating
Work Stations
The tool should only be used as a handheld hand operated tool. It is
always recommended that the tool is used when standing on the solid
floor. It can be
used in other
positions but
before any such
use, the opera-
tor must be in a
secure position
having a firm
grip and footing
and be aware
that the drill can
develop a
torque reaction
see section
"Operating".
No
Air Pressure
Recommended Working 6.3 bar 90 PSI
Recommended Minimum n/a bar n/a PSI
Maximum 7.0 bar 100 PSI
Personal Safety Equipment
Use - Safety Glasses
Yes
Use - Safety Gloves
Use - Safety Boots
Use - Breathing Masks
Use - Ear Protectors
Page No 1
Right Angle Drills
UT8807B 3/8" Capacity
UT8807B-1/2
1/2" Capacity
3/8 10 30 10
800
Includes - Foreseen Use, Work Stations, Putting Into Service, Operating,
Dismantling, Assembly and Safety Rules
Operator Instructions Important
Read these instructions carefully before installing, operating,
servicing or repairing this tool. Keep these instructions in a safe
accessible place.
Universal Air Tool Company Limited
Unit 8
Lane End Industrial Park
High Wycombe
Bucks
HP14 3BY
lbs
Kg
2.64 (3/8) 2.97 (1/2)
1.20 (3/8) 1.35 (1/2)
Vibration Level
Test Method Tested in accordance with ISO
standard 8662/1
Less than 2.5
Noise Level Sound Pressure Level 83.9 dB(A)
Test Method Tested in accordance with Pneurop
test code PN8NTC1 and ISO Standard 3744
Metres / Sec²

Operating
Select suitable drill bit, insert the shank into the drill chuck as far as
possible and tighten chuck with key supplied making sure that the
shank of the device is securely clamped centrally between the three
chuck jaws. Remove chuck key.
When drilling holes of all sizes it is advised to use a pointed punch to
mark the centre at which the hole is to be drilled as this will provide
a starting point for the drill tip. This procedure will prevent the drill bit
from skidding, ensure that the hole is drilled where intended and help
to prevent drill breakage when using small drills. When drilling,
particularly with small diameter drills, always try to ensure that load
applied to the drill is such that the drill bit is always at right angles to
the hole being drilled. Do not force the drill but allow it to cut.
When drilling always adopt a firm posture to be able to counteract any
sudden movement of the drill due to torque reaction. Such torque
reaction can occur when the drill stalls due to a too heavy load being
applied or the material being too hard or tough. The torque reaction
can occur when the drill breaks through the material being drilled,
particularly on sheet metal. Always use eye protection and hand
protection is advised, particularly when drilling holes in metals where
the material being removed from the hole is in the form of long sharp
strips. Do not tie the drill chuck key to the drill as the attaching device
i.e. string or chain could become entangled with the rotating chuck
and bit etc.
If using an abrasive device, drilling stone or performing any operation
where dust is created, it is recommended to use a breathing mask.
Always ensure that the material to be drilled is firmly fixed to prevent
its movement.
It is also recommended that when drilling holes of large diameter to
first pre drill a hole of smaller diameter as this will reduce effort
required to drill the hole and minimise torque reaction.
Dismantling & Assembly Instructions
Disconnect tool from air supply.
To remove the drive chuck (2) first open the chuck jaws with the key
provided and remove chuck screw(1) [left hand thread]. Place chuck
key securely into chuck and give the key a sharp tap so as to unscrew
a right hand thread. Grip motor housing (40) in a vice with soft jaws
on the flats at the rear end. Drive out pin (43) and take off throttle lever
(42). Unscrew inlet bushing (51) together with screen (52). With a
needle pointed tool, prise out deflector retainer (50), pull out deflector
(48) and remove O-Ring (49) from deflector (48). Unscrew 2 off
screws (47) and take off body cap (46), muffler (45) and gasket (44).
Unscrew valve screw (29) together with O-Ring (30) and reverse
retainer (31) and take out spring (32) and pull out valve pin (36), valve
(34), O-Ring retainer (33) and O-Ring (35).
Pull out reverse valve (37) and take out spring (38). Do not remove
either of the brass bushes in the motor housing (40) unless
replacements are required. If necessary reverse bush (39) can be
taken out of motor housing (40) by first removing pin (41). With circlip
pliers remove retaining ring (3) and pull out the output spindle
assembly. Unscrew nut (9), remove washer (8), bevel gear (7) and
key (5). Drive spindle (4) through bearing (6). Tap out needle bearing
(10) from angle head (11) but do not remove grease plug (12) unless
a replacement is required.
Slacken lock ring (15) and then unscrew angle head (11) [left hand
thread] from main assembly. Take out gear drive assembly and
dismantle by pressing pinion gear (13) through 2 off bearings (14).
Unscrew completely lock ring (15) and take out planet gear with pins
assembly (16), 3 off idler gears (17) and internal gear (18). Pull out the
motor assembly, complete with cylinder pin (25) from motor housing
(40).
Grip the front end plate (20) by hand and with a non metallic or soft
metal (lead or aluminium) hammer tap the splined end of the rotor
(21) to drive it through the front end plate (20) and bearing (19)
assembly. Tap out bearing (19) from front end plate (20). Remove
cylinder (23) and take out four off rotor blades (22) from rotor (21).
Take off retaining ring (28) from rotor (21) and support rear end plate
(24) in a piece of tube with a diameter as close as possible to the
maximum diameter of the rotor and tap the non splined end of the
rotor to drive it through the rear end plate (24) and bearing (27).
Take out motor gasket (26) from motor housing (40).
Reassembly
Clean all component parts and examine for wear before
reassembling. Use only manufacturer or distributor supplied parts.
Check in particular for wear on bevel gears, O-Rings and rotor blades.
Lightly coat all parts with a suitable pneumatic tool lubricating oil,
preferably one incorporating a rust inhibitor. Pack bearings and grease
gears and bevel gears with a lithium or molybdenum based general
purpose grease. Reassemble in the reverse order taking note of the
following:
1) When fitting gasket (26) make sure that it does not cover the ports
and is positioned correctly.
2) Make sure that the motor locating pin locates correctly in the holes
in the motor end plates and in the small hole between the two ports
at the bottom of the main bore of the motor housing.
3) Check the diameter of the pins in planet gear with pin assembly
(16). If the diameter of these pins falls below0.155" (3.93mm) replace
the assembly.
4) For the motor assembly, ensure that the motor end plates that abut
the cylinder are flat and free from burrs and sharp edges. If necessary
lap the faces on a very fine grade of abrasive paper laid on a flat
surface. Set the clearance between the rear end plate and the rotor
with the components pulled apart by hand to be between 0.0015"
(0.040mm) and 0.0025" (0.065mm).
oil preferably incorporating a rust inhibitor. Reconnect tool to air
supply and run tool slowly for a few seconds to allow air to circulate
the oil. If tool is used frequently lubricate on daily basis and if tool starts
to slow or lose power.
It is recommended that the air pressure at the tool whilst the tool is
running is 90 p.s.i./6.3 bar. The tool can run at lower and higher
pressures with the maximum permitted working air pressure of 100
p.s.i./7.0 bar.
Page No 2
Safety Rules When Using A Drill
1) Read all the instructions before using this tool. All operators must be
fully trained in its use and aware of these safety rules. All service and
repair must be carried out by trained personnel.
2) Always select a suitable cutting, abrasive device suitable for use
with this drill.
3) Always shut off the air supply to the drill and depress the trigger to
exhaust air from the feed hose before fitting, adjusting or removing the
device. Remove drill chuck.
4) Always adopt a firm footing and/or position and be aware of
torque reaction developed by the drill.
5) Use only correct spare parts.
6) Check hose and fittings regularly for wear. Do not carry the tool by
its hose and ensure that the hand is remote from the on/off valve
(trigger) when carrying the tool with air supply connected.
7) Do not exceed maximum recommended air pressure. Avoid low
air pressures as this will allow the drill to stall more easily and develop
torque reaction.
8) Use safety equipment as recommended.
9) The tool is not electrically insulated. Do not use where there is a
possibility of coming into contact with live electricity, gas pipes, water
pipes, etc. Check the area of operation before performing the
operation.
10) Take care against entanglement of moving parts of the tool with
clothing, ties, hair, cleaning rags, etc. This will cause the body to be
moved towards the work process and can be very dangerous.
11) Do not attempt to hold or guide the drill chuck when the tool is
running. Keep hands clear of the drilling process.
12) Use only compressed air at recommended conditions.
13) Do not attempt to fit attachments, i.e. for sawing, hedge cutting,
grinding, chain sawing, etc.
14) If the tool appears to malfunction remove from use immediately

UT8807B
UT8807B-1/2
3/8" Capacity Angle Drill
1/2" Capacity Angle Drill
Page No 3
Apr 1999 Ver 1.2
Ref No Part No Description
1900418 Chuck Screw
2H0019 Chuck 3/8" Capacity
H0020 Chuck 1/2" Capacity
3722001 Retaining Ring
4900419 Spindle
5900420 Key
6732229 Ball Bearing
7900421 Bevel Gear
8900422 Washer
9900423 Nut
10 731956 Needle Bearing
11 900424 Angle Head
12 900390 Grease Plug
13 900425 Pinion Gear
14 732191 Ball Bearing (2)
15 900426 Lock Ring
16 732446 Planet Gear w/Pin
17 731038 Idler Gear (3)
18 900427 Internal Gear
19 729188 Ball Bearing
20 900428 Front Plate
21 900429 Rotor
22 729709 Rotor Blade (4)
23 900104 Cylinder
24 900102 Rear End Plate
25 900105 Cylinder Pin
26 900113 Motor Gasket
Ref No Part No Description
27 729012 Ball Bearing
28 729180 Retaining Ring
29 900208 Valve Screw
30 729088 O-Ring
31 900200 Reverse Retainer
32 729063 Valve Spring
33 729043 O-Ring Retainer
34 731998 Valve
35 1008173 O-Ring
36 900193 Valve Pin
37 900194 Reverse Valve
38 900199 Reverse Spring
39 900195 Reverse Bush
40 900430 Motor Housing
41 731930 Roll Pin
42 900192 Throttle Lever
43 729167 Lever Pin
44 900198 Gasket
45 900209 Muffler
46 900197 Body Cap
47 900206 Screw (2)
48 729702 Deflector
49 1012371 O-Ring
50 729703 Deflector Retainer
51 900196 Inlet Bushing
52 1005726 Screen

Distributor
Notes
Page No 4
Accessories
and arrange for service and repair.
15) If an additional side handle is fitted to the tool ensure that it is
correctly positioned and fixed securely.
16) If the drill is used with a balancer or other suspension device
ensure that it is fixed securely.
Declaration of Conformity
Universal Air Tool Company Limited
Unit 8, Lane End Industrial Park, High Wycombe, Bucks, HP14 3BY, England
declare under our sole responsibility that the product
Model UT8807B Right Angle Drills, Serial Number
to which this declaration relates is in conformity with the following standard(s) or other normative document(s)
EN792 (Draft), EN292 Parts 1 & 2, ISO 8662 Part 1, Pneurop PN8NTC1
following the provisions of 89/392/EEC as amended by 91/368/EEC & 93/44/EEC Directives
Place and date of issue Name and signature or equivalent marking of authorised person
Lane End D.H.Moppett (Man Director)
This document may not be copied wholly or in part by anyone without the consent of the Directors of Universal Air Tool Company Limited
© Copyright of Universal Air Tool Company Limited, established in the United Kingdom, 1994
Designed & Written in the U.K.