UNIVIEW OET-213H-NB User manual

Face Recognition Access Control Terminal
User ManualⅡ
Document Version: V1.08

Thank you for purchasing our product. If there are any questions, or requests, please do not hesitate to contact
the dealer.
Disclaimer
No part of this manual may be copied, reproduced, translated, or distributed in any form or by any means without
prior written consent from us.
The manual may be updated from time to time due to version upgrade or other reasons.
The manual is for reference only. All the statements, information, and suggestions contained herein do not
constitute warranties of any kind, express or implied.
We shall not under any circumstances be liable for any special, consequential, incidental or indirect damages
arising from the use of this manual or our product, including but not limited to any loss of commercial profits,
losses caused by missing data or documents, and anomalies during product running or information leakage due
to cyber attacks, hacker attacks, or virus attacks.
Safety Precautions
CAUTION!
The default password is used for your first login. To ensure account security, please change the password after
your first login. You are recommended to set a strong password (no less than eight characters).
Before performing operations, be sure to carefully read through and observe safety specifications in this manual.
Screenshots provided in this document are used as examples only and the UI layout varies with versions.
This manual applies to multiple models but the models are not completely listed herein. Refer to actual
products while reading this manual.
We reserve the right to modify the content in this manual without prior notice or prompt, but we do
not ensure that this manual is completely error-free.
Subject to uncertain factors such as the physical environment, actual values of data may differ from the
reference values described here. In case of any question or dispute, the right of final interpretation
resides with us.
Follow operation instructions in this manual when using the product. We are not responsible for
problems caused by the violation of the instructions. Thank you for your cooperation.
Environmental Protection
This product has been designed to comply with the requirements on environmental protection. For the proper
storage, use and disposal of this product, national laws and regulations must be observed.
Conventions
The figures, charts or photos in this manual are used for illustration only, which may differ from the
actual product.
This manual applies to multiple models but the models are not completely listed herein. Refer to actual
products while reading this manual.

Subject to uncertain factors such as the physical environment, actual values of some data may differ
from the reference values described here. In case of any question or dispute, the right of final
interpretation resides with us.
Follow this manual when using the product. Professional guidance is recommended.
Notational conventions used in this document are described as follows:
Format
Description
Boldface
Indicates buttons, menus, tabs, window names, dialog names, and parameter names. For example, click
OK or select Device Management.
" "
Indicates messages. For example, "Hanging Up" is displayed on the interface.
>
Directs you to go to a multi-level menu. For example, go to Device Management > Add Device. In this
example, Add Device is a submenu under Device Management.
The symbols in the following table may be found in this manual. Carefully follow the instructions
indicated by the symbols to avoid hazardous situations and use the product properly.
Symbol
Description
WARNING!
Contains important safety instructions and indicates situations that could cause bodily injury.
CAUTION!
Means reader is careful and improper operations may cause damage or malfunction to product.
NOTE!
Means useful or supplemental information about the use of product.

i
Contents
1 Application Scope of the Manual··························································································1
2 Product Overview ···········································································································1
3 Product Appearance ········································································································1
4 Product Installation ·········································································································3
5 Local Operations·············································································································3
5.1 Initial Interface ··············································································································3
5.2 Main Interface···············································································································4
5.3 Ad Mode ·····················································································································5
5.4 Mask/Temperature Measurement Interface ············································································5
5.5 Activation Config ··········································································································10
5.5.1 Basic Info···········································································································11
5.5.2 Device Location ···································································································12
5.5.3 Network Setting···································································································12
5.5.4 User Management································································································12
5.5.5 Activation Password······························································································15
5.5.6 Admin Password ··································································································16
5.5.7 Authentication Scene ····························································································16
5.5.8 Volume·············································································································18
5.5.9 Device Maintenance······························································································18
5.5.10 Data Management ······························································································19
6 Personnel Management ·································································································· 20
6.1 Personnel Information Input·····························································································20
6.2 Personnel Deletion········································································································20
7 Web Operations ··········································································································· 20
7.1 Login ························································································································20
7.1.1 Preparation········································································································20
7.1.2 Logging In to the Web Interface ················································································22
7.2 Photo ·······················································································································24
7.2.1 Photo List Sorting ·································································································24
7.2.2 Total Capacity/Available Capacity ··············································································24
7.2.3 Photo Naming Rules······························································································24
7.2.4 Refreshing the Photo Library ····················································································25
7.2.5 Exporting Records ································································································25

ii
7.2.6 Exporting Photos··································································································25
7.2.7 Deleting a Photo ··································································································25
7.2.8 Exporting and Deleting Photos··················································································26
7.3 Parameter Configuration·································································································26
7.3.1 Common ···········································································································26
7.3.2 Network············································································································43
7.3.3 Image···············································································································44
7.3.4 Intelligent ··········································································································54
7.3.5 Events ··············································································································71
7.3.6 Storage·············································································································75
7.3.7 Security ············································································································77
7.3.8 System ·············································································································79
8 FAQs ························································································································ 82

1
1 Application Scope of the Manual
Table 1-1 Application Scope of the Manual
Model
Name
OET-213H-NB
Face Recognition Access Control Terminal
OET-523L-NB
Face Recognition Terminal
2 Product Overview
Face recognition access control terminal ("the face recognition terminal" for short) is a face recognition access
control product featuring high performance and high reliability. The face recognition technology is perfectly
integrated into the access control device, which relies on deep learning algorithm, to support face authentication
to open the door and achieve precise control of human. And it can be widely applied to the scenarios of building
systems, such as smart communities, public security, parks and other important areas.
3 Product Appearance
The figure below shows the structure of the device. The actual device shall prevail.
OET-213H-NB
Figure 3-1 Device Structure

2
1. Light supplement lamp 1
2. Camera 1
3. Infrared light supplement lamp
4. Camera 2
5. Light supplement lamp 2
6. Display screen
7. Pass-through indicator
8. Microphone
9. Card reading area
10. Loudspeaker
11. Reboot
12. USB2.0
13. Network interface
14. Power input (DC 12V±25%)
15. 20-pin interface
16. Tamper proof button
OET-523L-NB
Figure 3-2 Device Structure
1. Light supplement lampx2
2. Camera 1
3. Infrared light supplement lamp
4. Camera 2
5. Display screen
6. Pass-through indicator
7. Microphone
8. Loudspeaker
9. WIEGAND_OUT
10. WIEGAND_IN
11. RS232
12. RS485
13. Network interface
14. ALARM_IN
15. IO-1
16. IO-2

3
17. USB
18. Power output (DC 5V)
19. Power input (DC 12V±25%)
4 Product Installation
Installation of OET-213H-NB
For the wiring and installation of the device, refer to the Face Recognition Access Control Terminal Quick Guide.
Installation of OET-523L-NB
For the wiring and installation of the device, refer to the Face Recognition Terminal Quick Guide.
5 Local Operations
5.1 Initial Interface
When the face recognition terminal is used for the first time or the factory defaults are restored, users need to
set the activation password, which is used to log in to the Activation Config interface.
NOTE!
The password must contain at least eight characters (including at least two of the following types: upper
case letters, lower case letters, digits, underscores, and hyphens).
The activation password is consistent with the password for the admin to log in to the Web interface. If the
activation password is changed, use the new password to Logging In to the Web Interface
After the activation password is configured, the Figure 5-2 is displayed. If the activation password needs to be
changed later, refer to Activation Password to change the password.
Figure 5-1 Activation Password Configuration Interface

4
5.2 Main Interface
The main interface displayed on the face recognition terminal varies with the device type. See Device Info.
Figure 5-2 Main Interface
No.
Description
1
Displays the current date, time, and connection status of different services.
indicates the following items from left to right:
Whether to enable the face scan mode
Whether server 1 is online
NOTE!
An icon marked with indicates "No".
2
Total: total number of detected people.
Normal: Number of people with normal temperature
This interface is only displayed when the temperature measurement function is enabled. For detailed
operation description, see Advanced Setting.
3
Displays the photo and name of an identified person in the library. Refer to Recognition Result Display to
enable the face recognition terminal to display one or more registered face pictures.
When Multiple Faces is selected, information about the latest person identified successfully, is displayed
on the left of the screen. The interface can display information about five recent persons identified
successfully at most.

5
No.
Description
4
Title bar, which can be defined by users. For detailed operations, see Custom Logo and Prompt
5
Logo bar, which can be defined by users. For detailed operations, see Custom Logo and Prompt
6
Displays the identification result (such as identified successfully or unregistered person), authentication
mode (such as face scan or card swiping), and other information.
7
Displays the number of people in the employee library and that in the visitor library.
8
Status bar at the bottom
Displays the device IP address, temperature, temperature collection time, temperature measurement
module software and hardware version information and match time.
5.3 Ad Mode
The face recognition terminal supports ads (three pictures at most). For the ad configuration, see Ad Mode.
Figure 5-3 Ad Interface
In ad mode, the system does not exit the ad mode if a person passes the authentication (via face scan or card
swiping). If a person fails the face scan or taps the screen, the system exits the ad mode and the face recognition
terminal displays the Main Interface.
5.4 Mask/Temperature Measurement Interface
In response to the current epidemic, companies, parks, and communities take temperatures and check mask
wearing for people passing through the entrances and exits. The work is performed by people manually, which is
exhausting and increases the risk of cross-infection. The face recognition access control terminal is capable of
checking whether people are wearing masks and taking their temperatures (an intelligent digital detection module
is required, and either the forehead temperature or wrist temperature can be taken). For people with abnormal