Urbaco Luxor CC6U200PR Specification sheet

Luxor
Luxor
Technical Centre
Technical Centre
Installation, Use & Maintenance
Installation, Use & Maintenance
English
EN

Italiano ITItaliano ITItaliano IT
Pag.
2
2- Manual code:
119G9141
119 G 9141 ver.
3
302/2015 © URBACO S.A. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on URBACO S.A. to notify users.
English EN
Contents
Contents
1- Legend of symbols..........................................................................................................................................Pag.3
2-Conditions of use..............................................................................................................................................Pag.3
2.1-Intended use......................................................................................................................................Pag.3
2.2-Limits to use.....................................................................................................................................Pag.3
3-Reference Standards.......................................................................................................................................Pag.3
4-Descriptions............................................................................................................................................Pag.3
4.1-Technicalcentre-technicalfeatures.....................................................................................................Pag.3
4.2-Technical centre: components and dimensions ...............................................................................Pag.4
4.3-(Technical centre) Pneumatic performances.................................................................................Pag.5
5-Control panel....................................................................................................................................................Pag.6
5.1-Summary table of accessories’ power demands.............................................................................Pag.7
5.2-Electrical connections......................................................................................................................Pag.8
5.3-Release/discharge the system from/inside the centre..................................................................Pag.8
6-Technical centre installation...........................................................................................................................Pag.10
6.1-Preliminary checks..........................................................................................................................Pag.10
6.2-Fastening to the floor with reinforcement (optional)...................................................................Pag.11
7-Connecting additional devices.....................................................................................................................Pag.12
7.1-Cooling fans (optional)...................................................................................................................Pag.12
7.2-Heating unit (optional) ...................................................................................................................Pag.12
7.3-Mounting instructions for automatic purge with timer (optional)...................................................Pag.13
8-Safety instructions ........................................................................................................................................Pag.14
9-Maintenance.........................................................................................................................................Pag.14
9.1- Periodic maintenance....................................................................................................................Pag.14
9.2-Trouble shooting.............................................................................................................................Pag.14
9.3-Registro interventi..........................................................................................................................Pag.15
10-Phasing out and disposal...........................................................................................................................Pag.17
11-Declaration of conformity.............................................................................................................................Pag.17

Italiano ITItaliano ITItaliano IT
Pag.
3
3- Manual code:
119G9141
119 G 9141 ver.
3
302/2015 © URBACO S.A. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on URBACO S.A. to notify users.
English EN
“IMPORTANT INSTALLATION, SAFETY INSTRUCTIONS”
“CAUTION: IMPROPER INSTALLATION MAY CAUSE SERIOUS DAMAGE, FOLLOW ALL INSTALLATION INSTRUCTIONS CAREFULLY”
“THIS MANUAL IS ONLY FOR PROFESSIONAL OR QUALIFIED INSTALLERS”
1 Legend of symbols
1 Legend of symbols
This symbol tells you to read the section with particular care.
This symbol tells you that the sections concern safety issues.
This symbol tells you what to say to the end-users.
2 Intended use and limits to use
2 Intended use and limits to use
This product can be used only for purposes indicated in this manual
The use of this product for purposes other than those described above and installation executed in a manner other than as in-
structed in this technical manual are prohibited.
Urbaco has no responsibility for any improper use of the system
2.1 Intended use
Do not allow children to play or loiter within the movement area of the bollard.
Keep transmitters and any other command device out the reach of children, to prevent operator from being activated by acci-
dent.
2.2 Limits to use
3 Reference Standards
3 Reference Standards
This product complies with the following standards: see chapter 11 - Conformity declaration - pag. 17.
4 Descriptions
4 Descriptions
4.1 Technical centre - technical features
(Electric) power supply 230 V - 50/60Hz
Weight 1500 W
Draw when idle 100 mA
Protection rating IP 44-54
Acoustic pression 69-70 Db
Weight 60 kg
Cabinet material Laquered 15/10 sheet metal
Operating temperature -10° +55°
Duty cycle 50%

Italiano ITItaliano ITItaliano IT
2
11
11
10
10
9
5
345
6
1
7
8
a
b
c
da300
b806
c606
d100
e270
e
Pag.
4
4- Manual code:
119G9141
119 G 9141 ver.
3
302/2015 © URBACO S.A. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on URBACO S.A. to notify users.
English EN
1Compressorgroup/unit
2Controlpanel
3 Magnetic loops (optional)
4 Hot/Cold thermostats (optional)
5Coolingfans(optional)
6 Heating unit (optional)
7 Automatic purge (optional with timer)
8 Floor mounting basement (optional)
9 Air joints for bollards (Ø 10)
10 Air circuit discharge
11 Pressure regulator (manometer)
4.2 (Technical centre) Description: Components and dimensions

Italiano ITItaliano ITItaliano IT
Pag.
5
5- Manual code:
119G9141
119 G 9141 ver.
3
302/2015 © URBACO S.A. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on URBACO S.A. to notify users.
English EN
4.3 (Technical centre) Pneumatic performances
Max no. of manoeuvres per hour
No. of
bollards
Ø 200 Ø 270 Ø 320
h600h800h600h800h600h800
1 100 70 100 70 100 70
2 453545354535
3 302430243024
4 2418241824
518 18
616
Reliable values if T=25°C and compressor duty cycle of up to 40%
The no. of manoeuvres should be evenly distributed over time
The conduit length has influence on the max no. of manoeuvres per hour
For intensive use manoeuvres the use the aeration kit is required
Minimal interval between two subsequent manoeuvres (s)
No. of
bollards
Ø 200 Ø 270 Ø 320
h600h800h600h800h600h800
1 355035503550
2 801048010480104
3 120 150 120 150 120 150
4 150 190 150 190 150
5190 190
6225
Max no. of Luxor bollards operated simultaneously by a single technical centre
Max no.
of bollards
Ø 200 Ø 270 Ø 320
h 600 6 5 4
h 800 4 4 3
The following performances have been recorded with a 50 m long conduit of 10 mm diameter

Italiano ITItaliano ITItaliano IT
Compressor
LN
015
24
L2TL1T
1234
ON
5
1234
ON
5
1234
ON
5
8
Pag.
6
6- Manual code:
119G9141
119 G 9141 ver.
3
302/2015 © URBACO S.A. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on URBACO S.A. to notify users.
English EN
5 Card
5 Card
Trimmer for the automatic
closing time adjustment
Fuses
Buttons for radio
programming
Connector for radio
cards
Additional control boards for
managing up to 3 access ways
ON OFF
DIP n° 1 Automatic closing – enabled Automatic closing - disabled
DIP n° 2 Only-opening enabled Only-opening disabled
DIP n° 3 3” Pre-flashing enabled Pre-flashing disabled
DIP n° 4 Programming (see table below)
DIP n° 5
Table of fuses
Fuse for accessories 5A
Fuse for main line 630 mA
Fuse for control board 1A
Fuse for compressor 8A -T
Switch Button Led Option
N°4 N°5 CH1 CH2 After 5”
ON ON ON It enables the bistable solenoid valve
ON ON OFF It enables the monostable solenoid valve
ON ON ON It enables the acoustic signaller and the flashing of the red traffic light
ON ON OFF It disables the acoustic signaller
ON ON ON Green traffic light enabled
ON ON OFF Yellow traffic light enabled
ON ON ON “Presence” function is enabled (it is possible to retract the bollard only
when the loop detects the mass)
ON ON OFF “Presence” function is disabled
Put the n°4 and n° 5 dip switch into ON position, then press the CH1 or CH2 buttons. The led starts flashing. After 5”, if the led is
still flashing, it means that the option is enabled; if it is not, then the option is disabled.

Italiano ITItaliano ITItaliano IT
Pag.
7
7- Manual code:
119G9141
119 G 9141 ver.
3
302/2015 © URBACO S.A. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on URBACO S.A. to notify users.
English EN
U200 control panel to control 1 access way
Type of accessory
Single
accessory
power (W)
Max no. of
connectable
accessories and
bollards
Total power (W), if
with monostable
solenoid valve
Total power (W), if with
bistable solenoid valve
Monostable solenoid valve 86 48
Bistable solenoid valve * 38 24
Duty cycle 3618
824
Flashing light 25 1 25 25
Traffic light 11 2 22 22
Magnetic loop 2.5 3 7.5 7.5
Total (W) 120.5 102.5
U200 control panel + U201 board to control 2 separated access ways
Type of accessory
Single
accessory
power (W)
Max no. of
connectable
accessories and
bollards
Total power (W), if
with monostable
solenoid valve
Total power (W), if with
bistable solenoid valve
Monostable solenoid valve 86 48
Bistable solenoid valve * 38 24
Duty cycle 3618
824
Flashing light** 25 2 50 50
Traffic light ** 11 4 44 44
Magnetic loop 2.5 6 15 15
Total (W) 131 125 113 117
U200 control panel + two U201 boards to control 3 separated access ways
Type of accessory
Single
accessory
power (W)
Max no. of
connectable
accessories and
bollards
Total power (W), if
with monostable
solenoid valve
Total power (W), if with
bistable solenoid valve
Monostable solenoid valve 86 48
Bistable solenoid valve * 38 24
Duty cycle 3618
824
Flashing light *** 25 3 75 75
Traffic light *** 11 6 66 66
Magnetic loop 2.5 9 22.5 22.5 22.5 22.5
Total (W) 163.5 154.5 145.5 136.5
* The bistable solenoid valves are used in such systems, where the bollard should remain in the higher
position even when voltage is cut off
** If you use the flashing light you cannot use the traffic light
*** According to this configuration, the flashing lights or the traffic lights should be externally supplied.
5.1 Summary table of 24 V accessories’ power demand, expressed in W

Italiano ITItaliano ITItaliano IT
LN
LN
LN
LN
LN
LN
LN
Compressor
Pag.
8
8- Manual code:
119G9141
119 G 9141 ver.
3
302/2015 © URBACO S.A. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on URBACO S.A. to notify users.
English EN
5.2 Electrical connections
Line voltage 230V - 50/60Hz
Magnetic sensor/photocells max power supply (see tab. in chap. 5.1)
Flashing light output voltage 24V 25W
Red traffic light and illuminated ring (see tab. in chap. 5.1)
Yellow traffic light (see tab. in chap. 5.1)
Solenoid valve for the upward movement max voltage 24V AC (see tab. in chap. 5.1)
Solenoid valve for the downward movement 24V AC (optional) or downward
command for the bistable valve
Compressor

Italiano ITItaliano ITItaliano IT
LN
LN
LN
LN
1 2
Pag.
9
9- Manual code:
119G9141
119 G 9141 ver.
3
302/2015 © URBACO S.A. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on URBACO S.A. to notify users.
English EN
Compressor surveillance
N.C. STOP button
Step by step
Endstop - closing
Endstop - opening
SMA N.C. contact
Closing button
5.3 Release/discharge the system from/inside the centre
To discharge air from the system and consequently move down the bollards, you can open the tap nearby the pressure switch (we
recommend you to do it when the compressor is shut down, in order to avoid that it starts automatically to compensate the pres-
sure fall).To put the system into operation again, close the air discharge as shown in fig. 2 (and turn on the compressor, if you had
shut it down).
Purge opening Purge closing
Air supply tap to the bollards

Italiano ITItaliano ITItaliano IT
Pag.
10
10 - Manual code:
119G9141
119 G 9141 ver.
3
302/2015 © URBACO S.A. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on URBACO S.A. to notify users.
English EN
6 Technical centre installation
6 Technical centre installation
6.1 Preliminary checks
-Check that no conduits or other obstacles shall prevent from excavating and installating operations.
-Check the soil consistence and its loading capacity.
-On the power supply line provide an omnipolar disconnecting device with an opening distance between contacts equal to or
larger than 3 mm. We recommend you to use a 10 A omnipolar disconnecting device.
-Remove any obstacle that can prevent the bollard form a normal operating mode.
-The magnetic loops positioning has influence on the access correct functioning.
In fact, we recommend you to chose first the loops position, then the bollards one and then that for the technical centre.
-Position the technical centre in a way to protect it from accidental hurting.
-Provide for a conduit to pass connections through it.
-When necessary, you need to install optical and sound signalization to minimize dangerous situations.
-Air flexibles max length must not exceed 100 m
-Max distance of the cable connecting the feeder and the magnetic loop shall not exceed 50 m.
Table of connections
Air piping Rilsan PA11 - DIN 74324 Ø 10x8
Electrical connections between technical
centre and bollards
FG7(O) R0.6/1kW 10x1.5
Links between SMA and loop Min. 20 windings per meter Ø 1x1.5
Connection to the traffic light FG7(O) R0.6/1kW 3x1.5
Max depth for
magnetic loops: 150 mm
LOOPS
IN EXIT SAFETY
LOOP
PRESENCE
AND
SAFETY
LOOP
Min. distance between
conductors
ENTRANCE
EXIT
Control unit
Pit Sheath
Bollards
Sheaths