UROVO SR5600 User manual

SR5600 Bluetooth Scanner
Simple Operation Guide
3.01.200.XXXXXX
Device Appearance and Commonly Used Buttons Unpacking Instructions
Ring installation instructions
Direct charger installation instructions
Battery installation instructions
Device x 1 Battery x1
Direct charger x 1
Charger x1 Data cable x 1
Simple Operation Guide&Warranty Instructions&
Certificate of Conformity x 1
Packing List
Product Instructions
Align one end of the SR5600 lock catch and push the other end down
until it clicks into place. The ring can be installed as required. The
following figure 1 is for the right finger, and figure 2 is for the left finger.
Press the sliding buckle to remove the ring.
Insert the bottom of the SR5600 into the direct charger until it clips into
place. Connect the Type-C interface at the end of the direct charger
with the data cable and charger. Normal charging starts when the
indicator light indicates that the red light is always on.
Align the battery with the top of the SR5600 and insert it into the battery
compartment. Slide the battery all the way into the SR5600 locking slot
to ensure that the battery matches with SR5600.
Battery buckle
Indicator light
Battery Scanning head
Ring code scanning button
Comfort
cushion
Cord buckle Tape buckle
Direct charger
Finger tape
POGO PIN I. Press and hold the power button and then release it. After booting,
SR5600 Bluetooth scanner (hereinafter referred to as SR5600)
automatically enters the Bluetooth Standby Pairing mode, and the
blue light keeps flashing;
III. Connect the SR5600 with the main device Bluetooth, there are
II. If the Bluetooth is not connected, an alarm is generated when the
SR5600 scans the code successfully. The SR5600 automatically
shuts down if the Bluetooth connection fails in 5 minutes.
three connection methods as follows:
1. Search for the corresponding Bluetooth name SR5600-XXXX
(representing the last four digits of the Bluetooth Mac address) from
the Bluetooth list of the main device.
2. Connect via SR5600 NFC touch (press the NFC switch of the main
device, contact the main device with the SR5600 NFC, and follow the
steps prompted by the main device to successfully set up);
3. Connect by scanning the setting code (as described in Product
Instructions IV).
IV. After successful connection, the blue light is always on,the buzzer
buzz twice, and the device starts working;
V. To change the code system and other settings, download the
setting code APK or WeChat setting code applet from the official
account of "UROVO". After installation, set according to actual
requirements and the QR code will be generated. Scan the QR code
with SR5600, and the buzzer buzz twice, which indicates successful
setting.
Instructions for Status Light
Host code
scanning button
NFC
Sliding buckle
Power button
Figure1 Figure2
Battery lock catch
POGO PIN Type-C
Type-C
Ring buckle
（Direct charger）
Status light Description
Red indicator light is always on Scanning code or charging
R
Red indicator blinking twice
ed indicator light flashes once Setup failure
Alarm during code scanning when Bluetooth is
not connected
Green indicator light flashes once Scan code successfully
Green indicator light is always on
Blue indicator solid on
Battery fully charged
Successful Bluetooth connection
Blue indicator light keeps flashing Bluetooth enters pairing mode

SR5600 Bluetooth Scanner
Simple Operation Guide
3.01.200.XXXXXX
Device Appearance and Commonly Used Buttons Unpacking Instructions
Ring installation instructions
Direct charger installation instructions
Battery installation instructions
Device x 1 Battery x1
Direct charger x 1
Charger x1 Data cable x 1
Simple Operation Guide&Warranty Instructions&
Certificate of Conformity x 1
Packing List
Product Instructions
Align one end of the SR5600 lock catch and push the other end down
until it clicks into place. The ring can be installed as required. The
following figure 1 is for the right finger, and figure 2 is for the left finger.
Press the sliding buckle to remove the ring.
Insert the bottom of the SR5600 into the direct charger until it clips into
place. Connect the Type-C interface at the end of the direct charger
with the data cable and charger. Normal charging starts when the
indicator light indicates that the red light is always on.
Align the battery with the top of the SR5600 and insert it into the battery
compartment. Slide the battery all the way into the SR5600 locking slot
to ensure that the battery matches with SR5600.
Battery buckle
Indicator light
Battery Scanning head
Ring code scanning button
Comfort
cushion
Cord buckle Tape buckle
Direct charger
Finger tape
POGO PIN I. Press and hold the power button and then release it. After booting,
SR5600 Bluetooth scanner (hereinafter referred to as SR5600)
automatically enters the Bluetooth Standby Pairing mode, and the
blue light keeps flashing;
III. Connect the SR5600 with the main device Bluetooth, there are
II. If the Bluetooth is not connected, an alarm is generated when the
SR5600 scans the code successfully. The SR5600 automatically
shuts down if the Bluetooth connection fails in 5 minutes.
three connection methods as follows:
1. Search for the corresponding Bluetooth name SR5600-XXXX
(representing the last four digits of the Bluetooth Mac address) from
the Bluetooth list of the main device.
2. Connect via SR5600 NFC touch (press the NFC switch of the main
device, contact the main device with the SR5600 NFC, and follow the
steps prompted by the main device to successfully set up);
3. Connect by scanning the setting code (as described in Product
Instructions IV).
IV. After successful connection, the blue light is always on,the buzzer
buzz twice, and the device starts working;
V. To change the code system and other settings, download the
setting code APK or WeChat setting code applet from the official
account of "UROVO". After installation, set according to actual
requirements and the QR code will be generated. Scan the QR code
with SR5600, and the buzzer buzz twice, which indicates successful
setting.
Instructions for Status Light
Host code
scanning button
NFC
Sliding buckle
Power button
Figure1 Figure2
Battery lock catch
POGO PIN Type-C
Type-C
Ring buckle
（Direct charger）
Status light Description
Red indicator light is always on Scanning code or charging
R
Red indicator blinking twice
ed indicator light flashes once Setup failure
Alarm during code scanning when Bluetooth is
not connected
Green indicator light flashes once Scan code successfully
Green indicator light is always on
Blue indicator solid on
Battery fully charged
Successful Bluetooth connection
Blue indicator light keeps flashing Bluetooth enters pairing mode

SR5600 Bluetooth Scanner
Simple Operation Guide
3.01.200.XXXXXX
Device Appearance and Commonly Used Buttons Unpacking Instructions
Ring installation instructions
Direct charger installation instructions
Battery installation instructions
Device x 1 Battery x1
Direct charger x 1
Charger x1 Data cable x 1
Simple Operation Guide&Warranty Instructions&
Certificate of Conformity x 1
Packing List
Product Instructions
Align one end of the SR5600 lock catch and push the other end down
until it clicks into place. The ring can be installed as required. The
following figure 1 is for the right finger, and figure 2 is for the left finger.
Press the sliding buckle to remove the ring.
Insert the bottom of the SR5600 into the direct charger until it clips into
place. Connect the Type-C interface at the end of the direct charger
with the data cable and charger. Normal charging starts when the
indicator light indicates that the red light is always on.
Align the battery with the top of the SR5600 and insert it into the battery
compartment. Slide the battery all the way into the SR5600 locking slot
to ensure that the battery matches with SR5600.
Battery buckle
Indicator light
Battery Scanning head
Ring code scanning button
Comfort
cushion
Cord buckle Tape buckle
Direct charger
Finger tape
POGO PIN I. Press and hold the power button and then release it. After booting,
SR5600 Bluetooth scanner (hereinafter referred to as SR5600)
automatically enters the Bluetooth Standby Pairing mode, and the
blue light keeps flashing;
III. Connect the SR5600 with the main device Bluetooth, there are
II. If the Bluetooth is not connected, an alarm is generated when the
SR5600 scans the code successfully. The SR5600 automatically
shuts down if the Bluetooth connection fails in 5 minutes.
three connection methods as follows:
1. Search for the corresponding Bluetooth name SR5600-XXXX
(representing the last four digits of the Bluetooth Mac address) from
the Bluetooth list of the main device.
2. Connect via SR5600 NFC touch (press the NFC switch of the main
device, contact the main device with the SR5600 NFC, and follow the
steps prompted by the main device to successfully set up);
3. Connect by scanning the setting code (as described in Product
Instructions IV).
IV. After successful connection, the blue light is always on,the buzzer
buzz twice, and the device starts working;
V. To change the code system and other settings, download the
setting code APK or WeChat setting code applet from the official
account of "UROVO". After installation, set according to actual
requirements and the QR code will be generated. Scan the QR code
with SR5600, and the buzzer buzz twice, which indicates successful
setting.
Instructions for Status Light
Host code
scanning button
NFC
Sliding buckle
Power button
Figure1 Figure2
Battery lock catch
POGO PIN Type-C
Type-C
Ring buckle
（Direct charger）
Status light Description
Red indicator light is always on Scanning code or charging
R
Red indicator blinking twice
ed indicator light flashes once Setup failure
Alarm during code scanning when Bluetooth is
not connected
Green indicator light flashes once Scan code successfully
Green indicator light is always on
Blue indicator solid on
Battery fully charged
Successful Bluetooth connection
Blue indicator light keeps flashing Bluetooth enters pairing mode

SR5600 Bluetooth Scanner
Simple Operation Guide
3.01.200.XXXXXX
Device Appearance and Commonly Used Buttons Unpacking Instructions
Ring installation instructions
Direct charger installation instructions
Battery installation instructions
Device x 1 Battery x1
Direct charger x 1
Charger x1 Data cable x 1
Simple Operation Guide&Warranty Instructions&
Certificate of Conformity x 1
Packing List
Product Instructions
Align one end of the SR5600 lock catch and push the other end down
until it clicks into place. The ring can be installed as required. The
following figure 1 is for the right finger, and figure 2 is for the left finger.
Press the sliding buckle to remove the ring.
Insert the bottom of the SR5600 into the direct charger until it clips into
place. Connect the Type-C interface at the end of the direct charger
with the data cable and charger. Normal charging starts when the
indicator light indicates that the red light is always on.
Align the battery with the top of the SR5600 and insert it into the battery
compartment. Slide the battery all the way into the SR5600 locking slot
to ensure that the battery matches with SR5600.
Battery buckle
Indicator light
Battery Scanning head
Ring code scanning button
Comfort
cushion
Cord buckle Tape buckle
Direct charger
Finger tape
POGO PIN I. Press and hold the power button and then release it. After booting,
SR5600 Bluetooth scanner (hereinafter referred to as SR5600)
automatically enters the Bluetooth Standby Pairing mode, and the
blue light keeps flashing;
III. Connect the SR5600 with the main device Bluetooth, there are
II. If the Bluetooth is not connected, an alarm is generated when the
SR5600 scans the code successfully. The SR5600 automatically
shuts down if the Bluetooth connection fails in 5 minutes.
three connection methods as follows:
1. Search for the corresponding Bluetooth name SR5600-XXXX
(representing the last four digits of the Bluetooth Mac address) from
the Bluetooth list of the main device.
2. Connect via SR5600 NFC touch (press the NFC switch of the main
device, contact the main device with the SR5600 NFC, and follow the
steps prompted by the main device to successfully set up);
3. Connect by scanning the setting code (as described in Product
Instructions IV).
IV. After successful connection, the blue light is always on,the buzzer
buzz twice, and the device starts working;
V. To change the code system and other settings, download the
setting code APK or WeChat setting code applet from the official
account of "UROVO". After installation, set according to actual
requirements and the QR code will be generated. Scan the QR code
with SR5600, and the buzzer buzz twice, which indicates successful
setting.
Instructions for Status Light
Host code
scanning button
NFC
Sliding buckle
Power button
Figure1 Figure2
Battery lock catch
POGO PIN Type-C
Type-C
Ring buckle
（Direct charger）
Status light Description
Red indicator light is always on Scanning code or charging
R
Red indicator blinking twice
ed indicator light flashes once Setup failure
Alarm during code scanning when Bluetooth is
not connected
Green indicator light flashes once Scan code successfully
Green indicator light is always on
Blue indicator solid on
Battery fully charged
Successful Bluetooth connection
Blue indicator light keeps flashing Bluetooth enters pairing mode

Performance parameters
Instructions for Buzz and Vibration
Buzzer, vibration status Description
Start-up sound + no vibration Device successful startup
One long buzz + vibration Successful shutdown
One short buzz + vibration Successful decoding
Two short buzz + no vibration
The battery is set successfully, the Bluetooth is
connected successfully, and the Bluetooth is
disconnected
On
Four short beeps + vibration
e long buzz + no vibration Setup failure
Alarm during code scanning when Bluetooth is
not connected
Image sensor 1280 (horizontal) × 800 (vertical) CMOS, 60fps
Viewing angle 41°(H)×26°(V)
Reading angle rotation 360°, tilt ±60°, deflection ±60°
Reading depth of
field
Code39: 60~200mm (5mil) Code39: 80~550mm (20mil)
UPC-A: 50~400mm (13mil) PDF417: 50~300mm (6.7mil)
DM: 80~200mm (10mil) QRCode: 60~400mm (20mil)
Decoding tips
Input voltage and
current
Buzzer, LED tri-color light, vibration motor
USB 5V @500mA (max)
Communication
interface
Pogo pin contact
Sealing IP65
External dimension 62.9mm*33mm*18.7mm (length×width×height)
Weight 72 g (excluding direct charger)
Environmental
parameters
Working temperature: -20
℃~50℃
Storage temperature: -30℃~70℃
Working humidity: 5%RH~95%RH (non-condensing)
Drop height: 1.5 meters
Supported code
system
Linear: UPC/EAN/JAN, GS1 DataBar, Code 39, Code 128, Code 32, Code93,
Codabar/NW7, Interleaved 2 of 5, Code 2 of 5, Matrix 2 of 5, MSI, Telepen,
Trioptic, China Post
2D Stacked: PDF417, MicroPDF417, GS1 Composite
2D Matrix: Aztec Code, Data Matrix, QR Code, Micro QR Code, MaxiCode, Han
Xin
Postal: Intelligent Mail Barcode, Postal-4i, Australian Post, British Post,Canadian
Post, Japanese Post, Netherlands (KIX) Post, Postnet, Planet Code
OCR Option: OCR-A, OCR-B, E13B (MICR)
Precautions
1. Read all information in this guide before using the device to
ensure safe and proper operation.
2. Please use the accessories that have been approved by this
manufacturer and corresponds to this model. Use of any power
source, charger, battery, etc. that has not been approved by this
manufacturer may cause a fire, explosion, or other hazards.
3. Please use device and accessories within the specified
temperature range. Equipment failure may occur when the
ambient temperature is too high or too low.
4. Do not disassemble the product and its accessories. If the
equipment or any of its components are not working properly,
consult the after-sales service of the company promptly, or send
the equipment to the after-sales service outlet for testing and
maintenance.
5. The battery is made from a flammable and explosive material.
Do not disassemble, squeeze, drop and make any other
destructive operations on the battery. Do not place the battery in
high temperatures.
6. Disposal of used batteries is subject to local relevant
documents or policies regarding disposal of used batteries.
Warranty Policy
Thank you for using intelligent terminal series products. In the situation
of quality problems, which arise from raw materials or production
processes, during normal use of purchased products, the seller will be
responsible for free maintenance within one year from the date of
purchase.
The company may provide repairs due to the user's failure to use the
product according to the provided instructions of the product. However,
corresponding service fee and component fee will be charged.
Warranty regulations:
1. Under normal circumstances, the warranty period of the device is 12
months (3 months for accessories), subject to the sales agreement.
2. During the product warranty period, under the normal use conditions
(determined by our technical staff), the user will be entitled to a free
warranty for damaged or faulty warranty parts.
3. During the warranty period, faults caused by repair, disassembly or
modification of the product by a personnel other than our company,
improper installation, improper use by the user (failure to follow
instructions), serial number damage, accident or natural disaster, will
not be covered under the warranty.
4. The warranty will expire immediately if any alterations are made to
the warranty card.
5. Please show the equipment SN and purchase certificate for repair.
The company reserves the right to interpret the above contents.
Note: The contents of the manual are subject to change without prior notice.
This logo refers to the period ( 10 years ) during which the toxic or
hazardous substances or elements contained in electronic information
products will not leak or mutate so that the use of these [substances
or elements] will not result in any severe environmental pollution, any
bodily injury or damage to any assets.
：This symbol indicates that the content of this toxic or hazardous
substance in all homogeneous material is under the limit specified in the
SJ/T11363-2006
X ：This symbol indicates that the content of this toxic or hazardous
substance in at least one homogeneous material exceeds the limit
specifed in the SJ/T11363-2006; however, the exceeding toxic or
hazardous substance in the part with a "x" cannot be solved for there
is no mature technology can be used.
Battery Information
Caution:
1. Risk of explosion if battery is replaced by an incorrect type. Dispose
of batteries according to instructions.
2. However, there are limitations as to how long a battery can operate or
be stored before needing replacement. Many factors affect the actual life
cycle of a battery pack such as heat, cold,harsh environmental conditions,
and severe drops.
3. When batteries are stored over six months, some irreversible
deterioration in overall battery quality may occur. Store batteries at half of
full charge in a dry, cool place, removed from the equipment to prevent loss
of capacity, rusting of metallic parts, and electrolyte leakage. When storing
batteries for one year or longer, the charge level should be verified at least
once a year and charged to half of full charge.
4. Replace the battery when a significant loss of run time is detected.
Battery Safety Guidelines
1.The area in which the units are charged should be clear of debris and
combustible material or chemicals. Particular care should be taken where
the device is charged in non-commercial environment.
2. Follow battery usage, storage, and charging guidelines found in the
user’s guide.
3. Improper battery use may result in a fire, explosion, or other hazard.
4. To charge the mobile device battery, the battery and charger
temperatures must be between 0℃and +40℃.
5. Do not use incompatible batteries and chargers. Use of an incompatible
battery or charger may present a risk of fire, explosion, leakage, or other
hazard.
6. For devices that utilize a USB port as a charging source, the devise
shall only be connected to products that bear the USB-IF logo or have
completed the USB-IF compliance program.
7. Do not disassemble or open, crush, bend or deform, puncture, or shred.
8. Severe impact from dropping any battery-operated device on a hard
surface could cause the battery to overheat.
9. Do not short circuit a battery or allow metallic or conductive objects to
contact the battery terminals.
10. Do not modify or remanufacture, attempt to insert foreign objects into
the battery, immerse or expose to water or other liquids, or expose to fire,
explosion, or other hazard.
11. Do not leave or store the equipment in or near areas that might get
very hot, such as in a parked vehicle or near a radiator or other heat
source. Do not place battery into a microwave oven or dryer.
12. Battery usage by children should be supervised.
13. Please follow local regulations to promptly dispose of used
re-chargeable batteries.
14. Do not dispose of batteries in fire.
15. Seek medical advice immediately if a battery has been swallowed.
16. In the event of a battery leak, do not allow the liquid to come in
contact with the skin or eyes. If contact has been made, wash the
affected area with large amounts of water and seek medical advice.
Place of Origin: Shenzhen Quality Inspector: 02
UROVO TECHNOLOGY LTD.
Website: en.urovo.com
Table of Toxic and Hazardous Substances
and Content in this product
Part
Host
adapter
USB cable
Toxic and hazardous substances or elements
（Pb） （Hg） （Cd） （PBB）
（Cr(VI)） （PBDE）
X
X
X

Performance parameters
Instructions for Buzz and Vibration
Buzzer, vibration status Description
Start-up sound + no vibration Device successful startup
One long buzz + vibration Successful shutdown
One short buzz + vibration Successful decoding
Two short buzz + no vibration
The battery is set successfully, the Bluetooth is
connected successfully, and the Bluetooth is
disconnected
On
Four short beeps + vibration
e long buzz + no vibration Setup failure
Alarm during code scanning when Bluetooth is
not connected
Image sensor 1280 (horizontal) × 800 (vertical) CMOS, 60fps
Viewing angle 41°(H)×26°(V)
Reading angle rotation 360°, tilt ±60°, deflection ±60°
Reading depth of
field
Code39: 60~200mm (5mil) Code39: 80~550mm (20mil)
UPC-A: 50~400mm (13mil) PDF417: 50~300mm (6.7mil)
DM: 80~200mm (10mil) QRCode: 60~400mm (20mil)
Decoding tips
Input voltage and
current
Buzzer, LED tri-color light, vibration motor
USB 5V @500mA (max)
Communication
interface
Pogo pin contact
Sealing IP65
External dimension 62.9mm*33mm*18.7mm (length×width×height)
Weight 72 g (excluding direct charger)
Environmental
parameters
Working temperature: -20
℃~50℃
Storage temperature: -30℃~70℃
Working humidity: 5%RH~95%RH (non-condensing)
Drop height: 1.5 meters
Supported code
system
Linear: UPC/EAN/JAN, GS1 DataBar, Code 39, Code 128, Code 32, Code93,
Codabar/NW7, Interleaved 2 of 5, Code 2 of 5, Matrix 2 of 5, MSI, Telepen,
Trioptic, China Post
2D Stacked: PDF417, MicroPDF417, GS1 Composite
2D Matrix: Aztec Code, Data Matrix, QR Code, Micro QR Code, MaxiCode, Han
Xin
Postal: Intelligent Mail Barcode, Postal-4i, Australian Post, British Post,Canadian
Post, Japanese Post, Netherlands (KIX) Post, Postnet, Planet Code
OCR Option: OCR-A, OCR-B, E13B (MICR)
Precautions
1. Read all information in this guide before using the device to
ensure safe and proper operation.
2. Please use the accessories that have been approved by this
manufacturer and corresponds to this model. Use of any power
source, charger, battery, etc. that has not been approved by this
manufacturer may cause a fire, explosion, or other hazards.
3. Please use device and accessories within the specified
temperature range. Equipment failure may occur when the
ambient temperature is too high or too low.
4. Do not disassemble the product and its accessories. If the
equipment or any of its components are not working properly,
consult the after-sales service of the company promptly, or send
the equipment to the after-sales service outlet for testing and
maintenance.
5. The battery is made from a flammable and explosive material.
Do not disassemble, squeeze, drop and make any other
destructive operations on the battery. Do not place the battery in
high temperatures.
6. Disposal of used batteries is subject to local relevant
documents or policies regarding disposal of used batteries.
Warranty Policy
Thank you for using intelligent terminal series products. In the situation
of quality problems, which arise from raw materials or production
processes, during normal use of purchased products, the seller will be
responsible for free maintenance within one year from the date of
purchase.
The company may provide repairs due to the user's failure to use the
product according to the provided instructions of the product. However,
corresponding service fee and component fee will be charged.
Warranty regulations:
1. Under normal circumstances, the warranty period of the device is 12
months (3 months for accessories), subject to the sales agreement.
2. During the product warranty period, under the normal use conditions
(determined by our technical staff), the user will be entitled to a free
warranty for damaged or faulty warranty parts.
3. During the warranty period, faults caused by repair, disassembly or
modification of the product by a personnel other than our company,
improper installation, improper use by the user (failure to follow
instructions), serial number damage, accident or natural disaster, will
not be covered under the warranty.
4. The warranty will expire immediately if any alterations are made to
the warranty card.
5. Please show the equipment SN and purchase certificate for repair.
The company reserves the right to interpret the above contents.
Note: The contents of the manual are subject to change without prior notice.
This logo refers to the period ( 10 years ) during which the toxic or
hazardous substances or elements contained in electronic information
products will not leak or mutate so that the use of these [substances
or elements] will not result in any severe environmental pollution, any
bodily injury or damage to any assets.
：This symbol indicates that the content of this toxic or hazardous
substance in all homogeneous material is under the limit specified in the
SJ/T11363-2006
X ：This symbol indicates that the content of this toxic or hazardous
substance in at least one homogeneous material exceeds the limit
specifed in the SJ/T11363-2006; however, the exceeding toxic or
hazardous substance in the part with a "x" cannot be solved for there
is no mature technology can be used.
Battery Information
Caution:
1. Risk of explosion if battery is replaced by an incorrect type. Dispose
of batteries according to instructions.
2. However, there are limitations as to how long a battery can operate or
be stored before needing replacement. Many factors affect the actual life
cycle of a battery pack such as heat, cold,harsh environmental conditions,
and severe drops.
3. When batteries are stored over six months, some irreversible
deterioration in overall battery quality may occur. Store batteries at half of
full charge in a dry, cool place, removed from the equipment to prevent loss
of capacity, rusting of metallic parts, and electrolyte leakage. When storing
batteries for one year or longer, the charge level should be verified at least
once a year and charged to half of full charge.
4. Replace the battery when a significant loss of run time is detected.
Battery Safety Guidelines
1.The area in which the units are charged should be clear of debris and
combustible material or chemicals. Particular care should be taken where
the device is charged in non-commercial environment.
2. Follow battery usage, storage, and charging guidelines found in the
user’s guide.
3. Improper battery use may result in a fire, explosion, or other hazard.
4. To charge the mobile device battery, the battery and charger
temperatures must be between 0℃and +40℃.
5. Do not use incompatible batteries and chargers. Use of an incompatible
battery or charger may present a risk of fire, explosion, leakage, or other
hazard.
6. For devices that utilize a USB port as a charging source, the devise
shall only be connected to products that bear the USB-IF logo or have
completed the USB-IF compliance program.
7. Do not disassemble or open, crush, bend or deform, puncture, or shred.
8. Severe impact from dropping any battery-operated device on a hard
surface could cause the battery to overheat.
9. Do not short circuit a battery or allow metallic or conductive objects to
contact the battery terminals.
10. Do not modify or remanufacture, attempt to insert foreign objects into
the battery, immerse or expose to water or other liquids, or expose to fire,
explosion, or other hazard.
11. Do not leave or store the equipment in or near areas that might get
very hot, such as in a parked vehicle or near a radiator or other heat
source. Do not place battery into a microwave oven or dryer.
12. Battery usage by children should be supervised.
13. Please follow local regulations to promptly dispose of used
re-chargeable batteries.
14. Do not dispose of batteries in fire.
15. Seek medical advice immediately if a battery has been swallowed.
16. In the event of a battery leak, do not allow the liquid to come in
contact with the skin or eyes. If contact has been made, wash the
affected area with large amounts of water and seek medical advice.
Place of Origin: Shenzhen Quality Inspector: 02
UROVO TECHNOLOGY LTD.
Website: en.urovo.com
Table of Toxic and Hazardous Substances
and Content in this product
Part
Host
adapter
USB cable
Toxic and hazardous substances or elements
（Pb） （Hg） （Cd） （PBB）
（Cr(VI)） （PBDE）
X
X
X

Performance parameters
Instructions for Buzz and Vibration
Buzzer, vibration status Description
Start-up sound + no vibration Device successful startup
One long buzz + vibration Successful shutdown
One short buzz + vibration Successful decoding
Two short buzz + no vibration
The battery is set successfully, the Bluetooth is
connected successfully, and the Bluetooth is
disconnected
On
Four short beeps + vibration
e long buzz + no vibration Setup failure
Alarm during code scanning when Bluetooth is
not connected
Image sensor 1280 (horizontal) × 800 (vertical) CMOS, 60fps
Viewing angle 41°(H)×26°(V)
Reading angle rotation 360°, tilt ±60°, deflection ±60°
Reading depth of
field
Code39: 60~200mm (5mil) Code39: 80~550mm (20mil)
UPC-A: 50~400mm (13mil) PDF417: 50~300mm (6.7mil)
DM: 80~200mm (10mil) QRCode: 60~400mm (20mil)
Decoding tips
Input voltage and
current
Buzzer, LED tri-color light, vibration motor
USB 5V @500mA (max)
Communication
interface
Pogo pin contact
Sealing IP65
External dimension 62.9mm*33mm*18.7mm (length×width×height)
Weight 72 g (excluding direct charger)
Environmental
parameters
Working temperature: -20
℃~50℃
Storage temperature: -30℃~70℃
Working humidity: 5%RH~95%RH (non-condensing)
Drop height: 1.5 meters
Supported code
system
Linear: UPC/EAN/JAN, GS1 DataBar, Code 39, Code 128, Code 32, Code93,
Codabar/NW7, Interleaved 2 of 5, Code 2 of 5, Matrix 2 of 5, MSI, Telepen,
Trioptic, China Post
2D Stacked: PDF417, MicroPDF417, GS1 Composite
2D Matrix: Aztec Code, Data Matrix, QR Code, Micro QR Code, MaxiCode, Han
Xin
Postal: Intelligent Mail Barcode, Postal-4i, Australian Post, British Post,Canadian
Post, Japanese Post, Netherlands (KIX) Post, Postnet, Planet Code
OCR Option: OCR-A, OCR-B, E13B (MICR)
Precautions
1. Read all information in this guide before using the device to
ensure safe and proper operation.
2. Please use the accessories that have been approved by this
manufacturer and corresponds to this model. Use of any power
source, charger, battery, etc. that has not been approved by this
manufacturer may cause a fire, explosion, or other hazards.
3. Please use device and accessories within the specified
temperature range. Equipment failure may occur when the
ambient temperature is too high or too low.
4. Do not disassemble the product and its accessories. If the
equipment or any of its components are not working properly,
consult the after-sales service of the company promptly, or send
the equipment to the after-sales service outlet for testing and
maintenance.
5. The battery is made from a flammable and explosive material.
Do not disassemble, squeeze, drop and make any other
destructive operations on the battery. Do not place the battery in
high temperatures.
6. Disposal of used batteries is subject to local relevant
documents or policies regarding disposal of used batteries.
Warranty Policy
Thank you for using intelligent terminal series products. In the situation
of quality problems, which arise from raw materials or production
processes, during normal use of purchased products, the seller will be
responsible for free maintenance within one year from the date of
purchase.
The company may provide repairs due to the user's failure to use the
product according to the provided instructions of the product. However,
corresponding service fee and component fee will be charged.
Warranty regulations:
1. Under normal circumstances, the warranty period of the device is 12
months (3 months for accessories), subject to the sales agreement.
2. During the product warranty period, under the normal use conditions
(determined by our technical staff), the user will be entitled to a free
warranty for damaged or faulty warranty parts.
3. During the warranty period, faults caused by repair, disassembly or
modification of the product by a personnel other than our company,
improper installation, improper use by the user (failure to follow
instructions), serial number damage, accident or natural disaster, will
not be covered under the warranty.
4. The warranty will expire immediately if any alterations are made to
the warranty card.
5. Please show the equipment SN and purchase certificate for repair.
The company reserves the right to interpret the above contents.
Note: The contents of the manual are subject to change without prior notice.
This logo refers to the period ( 10 years ) during which the toxic or
hazardous substances or elements contained in electronic information
products will not leak or mutate so that the use of these [substances
or elements] will not result in any severe environmental pollution, any
bodily injury or damage to any assets.
：This symbol indicates that the content of this toxic or hazardous
substance in all homogeneous material is under the limit specified in the
SJ/T11363-2006
X ：This symbol indicates that the content of this toxic or hazardous
substance in at least one homogeneous material exceeds the limit
specifed in the SJ/T11363-2006; however, the exceeding toxic or
hazardous substance in the part with a "x" cannot be solved for there
is no mature technology can be used.
Battery Information
Caution:
1. Risk of explosion if battery is replaced by an incorrect type. Dispose
of batteries according to instructions.
2. However, there are limitations as to how long a battery can operate or
be stored before needing replacement. Many factors affect the actual life
cycle of a battery pack such as heat, cold,harsh environmental conditions,
and severe drops.
3. When batteries are stored over six months, some irreversible
deterioration in overall battery quality may occur. Store batteries at half of
full charge in a dry, cool place, removed from the equipment to prevent loss
of capacity, rusting of metallic parts, and electrolyte leakage. When storing
batteries for one year or longer, the charge level should be verified at least
once a year and charged to half of full charge.
4. Replace the battery when a significant loss of run time is detected.
Battery Safety Guidelines
1.The area in which the units are charged should be clear of debris and
combustible material or chemicals. Particular care should be taken where
the device is charged in non-commercial environment.
2. Follow battery usage, storage, and charging guidelines found in the
user’s guide.
3. Improper battery use may result in a fire, explosion, or other hazard.
4. To charge the mobile device battery, the battery and charger
temperatures must be between 0℃and +40℃.
5. Do not use incompatible batteries and chargers. Use of an incompatible
battery or charger may present a risk of fire, explosion, leakage, or other
hazard.
6. For devices that utilize a USB port as a charging source, the devise
shall only be connected to products that bear the USB-IF logo or have
completed the USB-IF compliance program.
7. Do not disassemble or open, crush, bend or deform, puncture, or shred.
8. Severe impact from dropping any battery-operated device on a hard
surface could cause the battery to overheat.
9. Do not short circuit a battery or allow metallic or conductive objects to
contact the battery terminals.
10. Do not modify or remanufacture, attempt to insert foreign objects into
the battery, immerse or expose to water or other liquids, or expose to fire,
explosion, or other hazard.
11. Do not leave or store the equipment in or near areas that might get
very hot, such as in a parked vehicle or near a radiator or other heat
source. Do not place battery into a microwave oven or dryer.
12. Battery usage by children should be supervised.
13. Please follow local regulations to promptly dispose of used
re-chargeable batteries.
14. Do not dispose of batteries in fire.
15. Seek medical advice immediately if a battery has been swallowed.
16. In the event of a battery leak, do not allow the liquid to come in
contact with the skin or eyes. If contact has been made, wash the
affected area with large amounts of water and seek medical advice.
Place of Origin: Shenzhen Quality Inspector: 02
UROVO TECHNOLOGY LTD.
Website: en.urovo.com
Table of Toxic and Hazardous Substances
and Content in this product
Part
Host
adapter
USB cable
Toxic and hazardous substances or elements
（Pb） （Hg） （Cd） （PBB）
（Cr(VI)） （PBDE）
X
X
X

Performance parameters
Instructions for Buzz and Vibration
Buzzer, vibration status Description
Start-up sound + no vibration Device successful startup
One long buzz + vibration Successful shutdown
One short buzz + vibration Successful decoding
Two short buzz + no vibration
The battery is set successfully, the Bluetooth is
connected successfully, and the Bluetooth is
disconnected
On
Four short beeps + vibration
e long buzz + no vibration Setup failure
Alarm during code scanning when Bluetooth is
not connected
Image sensor 1280 (horizontal) × 800 (vertical) CMOS, 60fps
Viewing angle 41°(H)×26°(V)
Reading angle rotation 360°, tilt ±60°, deflection ±60°
Reading depth of
field
Code39: 60~200mm (5mil) Code39: 80~550mm (20mil)
UPC-A: 50~400mm (13mil) PDF417: 50~300mm (6.7mil)
DM: 80~200mm (10mil) QRCode: 60~400mm (20mil)
Decoding tips
Input voltage and
current
Buzzer, LED tri-color light, vibration motor
USB 5V @500mA (max)
Communication
interface
Pogo pin contact
Sealing IP65
External dimension 62.9mm*33mm*18.7mm (length×width×height)
Weight 72 g (excluding direct charger)
Environmental
parameters
Working temperature: -20
℃~50℃
Storage temperature: -30℃~70℃
Working humidity: 5%RH~95%RH (non-condensing)
Drop height: 1.5 meters
Supported code
system
Linear: UPC/EAN/JAN, GS1 DataBar, Code 39, Code 128, Code 32, Code93,
Codabar/NW7, Interleaved 2 of 5, Code 2 of 5, Matrix 2 of 5, MSI, Telepen,
Trioptic, China Post
2D Stacked: PDF417, MicroPDF417, GS1 Composite
2D Matrix: Aztec Code, Data Matrix, QR Code, Micro QR Code, MaxiCode, Han
Xin
Postal: Intelligent Mail Barcode, Postal-4i, Australian Post, British Post,Canadian
Post, Japanese Post, Netherlands (KIX) Post, Postnet, Planet Code
OCR Option: OCR-A, OCR-B, E13B (MICR)
Precautions
1. Read all information in this guide before using the device to
ensure safe and proper operation.
2. Please use the accessories that have been approved by this
manufacturer and corresponds to this model. Use of any power
source, charger, battery, etc. that has not been approved by this
manufacturer may cause a fire, explosion, or other hazards.
3. Please use device and accessories within the specified
temperature range. Equipment failure may occur when the
ambient temperature is too high or too low.
4. Do not disassemble the product and its accessories. If the
equipment or any of its components are not working properly,
consult the after-sales service of the company promptly, or send
the equipment to the after-sales service outlet for testing and
maintenance.
5. The battery is made from a flammable and explosive material.
Do not disassemble, squeeze, drop and make any other
destructive operations on the battery. Do not place the battery in
high temperatures.
6. Disposal of used batteries is subject to local relevant
documents or policies regarding disposal of used batteries.
Warranty Policy
Thank you for using intelligent terminal series products. In the situation
of quality problems, which arise from raw materials or production
processes, during normal use of purchased products, the seller will be
responsible for free maintenance within one year from the date of
purchase.
The company may provide repairs due to the user's failure to use the
product according to the provided instructions of the product. However,
corresponding service fee and component fee will be charged.
Warranty regulations:
1. Under normal circumstances, the warranty period of the device is 12
months (3 months for accessories), subject to the sales agreement.
2. During the product warranty period, under the normal use conditions
(determined by our technical staff), the user will be entitled to a free
warranty for damaged or faulty warranty parts.
3. During the warranty period, faults caused by repair, disassembly or
modification of the product by a personnel other than our company,
improper installation, improper use by the user (failure to follow
instructions), serial number damage, accident or natural disaster, will
not be covered under the warranty.
4. The warranty will expire immediately if any alterations are made to
the warranty card.
5. Please show the equipment SN and purchase certificate for repair.
The company reserves the right to interpret the above contents.
Note: The contents of the manual are subject to change without prior notice.
This logo refers to the period ( 10 years ) during which the toxic or
hazardous substances or elements contained in electronic information
products will not leak or mutate so that the use of these [substances
or elements] will not result in any severe environmental pollution, any
bodily injury or damage to any assets.
：This symbol indicates that the content of this toxic or hazardous
substance in all homogeneous material is under the limit specified in the
SJ/T11363-2006
X ：This symbol indicates that the content of this toxic or hazardous
substance in at least one homogeneous material exceeds the limit
specifed in the SJ/T11363-2006; however, the exceeding toxic or
hazardous substance in the part with a "x" cannot be solved for there
is no mature technology can be used.
Battery Information
Caution:
1. Risk of explosion if battery is replaced by an incorrect type. Dispose
of batteries according to instructions.
2. However, there are limitations as to how long a battery can operate or
be stored before needing replacement. Many factors affect the actual life
cycle of a battery pack such as heat, cold,harsh environmental conditions,
and severe drops.
3. When batteries are stored over six months, some irreversible
deterioration in overall battery quality may occur. Store batteries at half of
full charge in a dry, cool place, removed from the equipment to prevent loss
of capacity, rusting of metallic parts, and electrolyte leakage. When storing
batteries for one year or longer, the charge level should be verified at least
once a year and charged to half of full charge.
4. Replace the battery when a significant loss of run time is detected.
Battery Safety Guidelines
1.The area in which the units are charged should be clear of debris and
combustible material or chemicals. Particular care should be taken where
the device is charged in non-commercial environment.
2. Follow battery usage, storage, and charging guidelines found in the
user’s guide.
3. Improper battery use may result in a fire, explosion, or other hazard.
4. To charge the mobile device battery, the battery and charger
temperatures must be between 0℃and +40℃.
5. Do not use incompatible batteries and chargers. Use of an incompatible
battery or charger may present a risk of fire, explosion, leakage, or other
hazard.
6. For devices that utilize a USB port as a charging source, the devise
shall only be connected to products that bear the USB-IF logo or have
completed the USB-IF compliance program.
7. Do not disassemble or open, crush, bend or deform, puncture, or shred.
8. Severe impact from dropping any battery-operated device on a hard
surface could cause the battery to overheat.
9. Do not short circuit a battery or allow metallic or conductive objects to
contact the battery terminals.
10. Do not modify or remanufacture, attempt to insert foreign objects into
the battery, immerse or expose to water or other liquids, or expose to fire,
explosion, or other hazard.
11. Do not leave or store the equipment in or near areas that might get
very hot, such as in a parked vehicle or near a radiator or other heat
source. Do not place battery into a microwave oven or dryer.
12. Battery usage by children should be supervised.
13. Please follow local regulations to promptly dispose of used
re-chargeable batteries.
14. Do not dispose of batteries in fire.
15. Seek medical advice immediately if a battery has been swallowed.
16. In the event of a battery leak, do not allow the liquid to come in
contact with the skin or eyes. If contact has been made, wash the
affected area with large amounts of water and seek medical advice.
Place of Origin: Shenzhen Quality Inspector: 02
UROVO TECHNOLOGY LTD.
Website: en.urovo.com
Table of Toxic and Hazardous Substances
and Content in this product
Part
Host
adapter
USB cable
Toxic and hazardous substances or elements
（Pb） （Hg） （Cd） （PBB）
（Cr(VI)） （PBDE）
X
X
X