Ursalink UC11-N1 User manual

1
UC11-N1
Quick Start Guide
Ursalink Technology Co., Ltd.

www.ursalink.com
1
Welcome
Thank you for choosing Ursalink UC11-N1.
This guide will teach you how to install the UC11-N1 and how to connect to Ursalink Cloud. Once you
complete the installation, refer to the Ursalink UC11-N1 User Guide on how to perform configurations on
the device.
Related Documents
This Start Guide only explains the installation of Ursalink UC11-N1. For more functionality and advanced
settings, please refer to the relevant documents as below.
Document
Description
Ursalink UC11-N1 Datasheet
Datasheet for the Ursalink UC11-N1.
Ursalink UC11-N1 User Guide
Users can refer to the guide on how to configure all the settings.
The related documents are available on Ursalink website: http://www.ursalink.com.
Declaration of Conformity
Ursalink UC11-N1 is in conformity with the essential requirements and other relevant provisions of the CE,
FCC, and RoHS.
For assistance, please contact
Ursalink technical support:
Email: [e-mail]
Tel: [phone]
Fax: [phone]

Ursalink UC11-N1 Quick Start Guide
www.ursalink.com
2
Before you begin to install the UC11-N1, please check the package contents to verify that you have received
the items below.
1 × DC Power Cable
(DC version only)
1 × Wall Mounting Kit
2 × Pole Mounting Kit
(Optional)
1 × Solar Panel Kit
(Optional)
If any of the above items is missing or damaged, please contact your Ursalink sales
Representative.
2.1 Terminal Description
1 × UC11-N1 Device
2 × Data Cable
1 × USB Cable
1 × Magnet
Setscrews
1 × Warranty Card
1. Packing List
2. Hardware Introduction

Ursalink UC11-N1 Quick Start Guide
www.ursalink.com
3
2.2 Dimensions(mm)
2.3 Pinouts
Interface 1
Interface 2
USB&Power Connector
PIN
Definition
1
5V/9V/12V
2
3.3V
3
GND
4
GPIO1
5
GPIO2
6
Switchable
Interfaces
7
8
Reserved
PIN
RS232
RS485
6
TXD
A
7
RXD
B
PIN
Definition
1
5V/9V/12V
2
3.3V
3
GND
4
AIN1
5
AIN2
6
Reserved
PIN
Definition
1
GND
2
USB_D+
3
USB_D-
4
VCC(5-24V)

Ursalink UC11-N1 Quick Start Guide
www.ursalink.com
4
A.
3.1 Turn ON/OFF UC11-N1
3.2 Hardware Switch
When using the analog input and power output of UC11-N1, you can switch the working mode of hardware
interface. Please follow the steps:
A. Remove the screw caps and take off the roof cover.
B. Change DIP switches that are related analog inputs and power outputs as shown in Section 2.1.
C. Put back the roof cover and screw the screws.
Note: Analog inputs are set to 4-20mA by default, power outputs are set to 12V by default.
3. Hardware Configuration and Installation
Place the magnet on the sign “U” to turn on/off UC11-N1.
Power on: Beep for 2 seconds
Power off: Beep for 6 seconds

Ursalink UC11-N1 Quick Start Guide
www.ursalink.com
5
3.3 USB Configuration
Connect UC11-N1 to laptop via USB cable.
3.4 Mount the UC11-N1
Wall Mounting
Make sure you have wall mounting bracket, bracket mounting screws, wall plugs, wall mounting screws and
other required tools.
A. Mount the enclosure to the mounting bracket with the bracket mounting screws.
B. Align the mounting bracket horizontally to the desired position on the wall, use a marker pen to mark
four mounting holes on the wall, and then remove the mounting bracket from the wall.
Note: The connecting lines of adjacent points are at right angles.
C. Drill the four holes by using your drill with a 6 mm drill bit on the positions you marked previously on the
wall.
D. Insert four wall plugs into the holes respectively.
E. Mount the mounting bracket horizontally to the wall by fixing the wall mounting screws into the wall
plugs.

Ursalink UC11-N1 Quick Start Guide
www.ursalink.com
6
Pole Mounting
Make sure you have wall mounting bracket, bracket mounting screws, hose clamp and other required tools.
A. Mount the enclosure to the mounting bracket with the bracket mounting screws.
B. Loosen the hose clamp by turning the locking mechanism counter-clockwise.
C. Straighten out the hose clamp and slide it through the rectangular holes in the mounting bracket, wrap
the hose clamp around the pole.
D. Use a screwdriver to tighten the locking mechanism by turning it clockwise.

Ursalink UC11-N1 Quick Start Guide
www.ursalink.com
7
This chapter takes example of how to reazlie remote monitoring of sensor data among UC11-N1,
Ursalink Cloud and sensor with RS485 serial port.
4.1 Configure UC11-N1 via Toolbox
A. Connect PC and UC11-N1 directly via USB port as shown in Section 3.3.
B. Download Toolbox software from Ursalink website and open Toolbox.exe. Select correct Serial Port fill in
the password to log in. (Default password: 123456)
Toolbox Download link: https://www.ursalink.com/en/software-download/
C.Click “Status” to check property of UC11-N1.
D. Click “General->Basic” to configure the “Reporting Interval”.
4. Connect N1 to Ursalink Cloud

Ursalink UC11-N1 Quick Start Guide
www.ursalink.com
8
E. Click “General->Serial” to configure RS485 property and Modbus channels.
4.2 RS485 Configuration Example
UC11-N1 collects data from two Modbus RTU sensors and provides power to them.
Sensor property:
Sensor
Serial Port
Slave ID
Address
Type
Power Supply
Light Sensor
9600 8N1
1
6
Holding Register (INT16)
12VDC
Wind speed sensor
9600 8N1
2
0
Holding Register (INT16)
12VDC
Configuration Steps:
A. Connect RS485 and power output of UC11-N1 to sensors. Wiring method:
UC11-N1
Orange (12V/9V/5V)
Brown (V+)
Sensors
Black (GND)
Brown (V-)
Green (A)
Green (A)
Yellow (B)
Blue (B)
B. Go to “General->Serial” to enable and select interface type as “RS485 (Modbus Master)”.
Enable interface 1 power output and configure “Power Output Time Before Collect”.

Ursalink UC11-N1 Quick Start Guide
www.ursalink.com
9
C. Configure Modbus Channels according to information of sensors. After saving configuration, click “Fetch”
to check if N1 read correct values.