UTEPO UTP101AR-HD User manual

DC12V 36V/AC 9V 24V;
Real time transfer of PAL、NTSC、SECAM video, HDCVI、AHD、HDTVI HD video;
Recommendation transmission distance as below:
Adopts UTP cable for the transmission, support DIP adjustment;
Wide range voltage AC/DC power input, strong surge protection and anti-interference
Delicate design, support MIT rack.
～ ～
1) HDCVI1080p: 330m; HDCVI 720P: 500m; ( passive to active);
2)HDTVI 720p/1080p: 300m ( passive to active);
3)AHD-L/M 720P/960P: 480m; AHD-H 1080P: 450m(passive to active);
4)Analog video: 650m ( passive to active);
The product adopts Cat 5/5e/6 UTP cable as transmission medium, It can receive color or
mono PAL/NTSC/SECAM video or HDCVI、AHD、HDTVI HD video in real time. It features
long transmission distance, good transmission effect, super anti-interference, wide CCTV
surveillance system.
1 3 4
12
2
Single Channel HD Video Active UTP Receiver
User Manual
Application
Feature
Notice
Please use standard UTP cable and coaxial to provide the transmission quality.
UTP101AT
Single channel HD Video Active UTP receiver
Board Diagram
.NO Component Description
For UTP cable
3
1
2
Power supply input
Green terminal block Grounding
Green terminal block
4switches
Video Output
For brightness adjustment
6BNC-M
Power supply block
MIT Pole For MIT Installation
1) Please power off the camera and monitor before installation;
2) Please connect the camera port and the transmitter's input port (BNC) with coaxial;
3) Please plug the monitor port and the receiver's output port (BNC) with coaxial
4) Please connect the UTP cable with the receiver and transmitter （VIDEO + - port）；
5) Please adjust the DIP adjustment according to the instruction;
6) Please examine the system.
Please check the following items before installation. If it’s missing, please contact the
dealer
Receiver 1set
User Manual 1set
Installation Steps
7
7
5
5switches
For color adjustment
6
Please follow the next installation steps:
VerB 1.0
UTP Cat5/5e/6
DVR
Power
HD Analog Video Acti ve
UTP Receiver
Monitor
Monitor
Coax
HD Analog Video Passive
UTP Balun

连接接口
Specification
Item
Description
Function
Transmission Channel
1ch
Output
2ch
Distance
Please refer to table 1
Power
Voltage Range
DC12V~36V or AC 9V~24V
Power Rate
<1W
Video
Transmission
Coaxial Port
Female BNC
UTP Cable Port
5pin port
Video System
PAL、NTSC、SECAM video,
.HDCVI、AHD、HDTVI HD video
Signal Bandwidth
0-7 MHz5
Anti-interference
>75dB
DIP
DIP Switch
Switch
Adjustment mode
Rotate
Status
Power LED
Red
Signal LED
Yellow
Protection
Power Port Protection
2KV 1KA Per IEC61000 4 5/ ： - -
Coaxial Port Protection
2KV(different mode) 4KV(common mode)
Per:IEC61000-4-5
ESD
1a contact discharge Level 2
1b air discharge Level 2
Per: IEC61000-4-2
Environment
Working Temperature
0 55℃~ ℃
Storage Temperature
-40℃~ ℃85
Humidity
0 95~ %
Structure
Size
115mm×82mm×22mm
Case
Iron
Color
Silver white
N W. .
180g
Specification change will not be noticed.
连接接口
Problem Examination
Please find the following solution when the device doesn't work
Please make sure the installation is according to the instruction;
Please make sure the RJ45 cable plug support 568A or 568B;
Please make sure each UTP cable is according to the related channel;
Please examine the port of BNC,RJ45;
Please make sure the distance exceed the max distance range;
Please make sure the transmission cable is reliable;
Please replace the failure product with a working one;
Please contact your local dealer if the problem still exist.
34
Single channel HD Video Active UTP receiver
UTP101AT
Single channel HD Video Active UTP receiver
Table 1:
Instruction:
The test data in table 1 is required under lab environment by passive to passive,In
actual case, there maybe some differences due to different cable and environment.
Signal Source
HDCVI
(720P)
HDCVI
(1080P)
HDTVI
(720P/1080P)
AHD-L/M
(720P/960P)
AHD-H
(1080P)
Analog
Video
Recommendation
distance
500m
330m
300m
480m
450m
650m