UWE AXM Series User manual

CONTENTS
CAUTIONS
1. INSTALLATION
2. SPECIFICATIONS
3. KEYBOARD LAYOUT AND DESCRIPTION
4. INITIAL SETUP
5. INSTRUCTION FOR USE
6. TROUBLE SHOOTING
7. DAILY CARE AND MAINTENANCE

CAUTIONS
1. This unit is legal for trade only when it is sealed
(and/or stamped) and bearing a serial number. Do not
attempt to break the seal (or stamp) affixed to this
scale or remove the serial number. Contact your dealer
for more information and after sales service.
2. For most accurate weighing result, do not use this
scale in where or when the environment condition falls
beyond as those listed on SPECIFICATIONS.
3. Do not attempt to open this unit or conduct any trouble
shootings other than those listed on TROUBLE
SHOOTING.
4. Do not use this scale for chemical substances or in
any environment that contains chemical vapor.
5. Precision measuring instrument, handle with care.
6. Do not open scale. No user serviceable parts inside.

1. INSTALLATION
1.1 Check and make sure that the following accessories
are included:
Operation Manual x 1
Scale x 1
Plastic platter x 1
Stainless steel cover x 1 (Optional)
Power adaptor x 1
Dust Cover x 1
Contact your dealer if any item is missing.
1.2 Place the stainless steel platter (if purchased)
onto the plastic platter.
1.3 Power on the scale
a. Before charging the scale or power on with the
adaptor supplied. Please make sure the input
voltage listed on the back of the adaptor matches
with the local voltage. If not, do not use it
and contact your dealer immediately.
b. Before first time use, charge the scale for at
least 8 hours to ensure the best performance.

2. SPECIFICATIONS
Model No.
Capacity
(Max)
Division (e)
OIML
Non-OIML
Extended
AXM-1500
1500g
0.5g
0.2g
0.05g
AXM-3000
3000g
1g
0.5g
0.1g
AXM-6000
6000g
2g
1g
0.2g
AXM-15K
15kg
0.005kg
0.002kg
0.0005kg
AXM-30K
30kg
0.01kg
0.005kg
0.001kg
Tare Range
Full Tare Range
Power-on
Zero Range
±10% Max
Zero Range
±2% Max
Min. Load
20e*
Power Source
By Built-in Rechargeable Battery or AD/DC
Power Adaptor
Operating
Environment
0o~40oC (32o~104oF),
Non-condensed. R.H.≦85%
Specifications subject to change without notice
*The minimum load of 1500g and 15kg for Non-OIML
application is 25e
NOTE 1:
OIML = Legal for trade (1/3000)
Non-OIML = Not legal for trade (1/6000~1/7500)
NOTE 2:
Extended Display Function does not support avoirdupois
weight units (lb/lb and lb/oz)

3. KEYBOARD LAYOUT AND DESCRIPTION
1. OFF KEY
Press this key to turn scale off
2. ON/ZERO KEY
Press this key to turn scale on or set weight to zero
3. MODE KEY
Press this key to shift among different weight units
and/or turn backlight on/off
4. TARE KEY
Press this key to tare off the weight of a container
5. WEIGHT UNIT INDICATOR
This indicator appears to indicate the weighing unit
currently engaged, metric (kg/g) or avoirdupois (lb,
lb/oz) weight units.

6. ZERO INDICATOR
This indicator appears to indicate a zero weight status
7. NET INDICATOR
This indicator appears to indicate the tare function
is in operation and weight displayed is net weight
8. LO-BAT INDICATOR
When this indicator appears, recharge the scale
immediately. Failure to do so may cause unrecoverable
damage to the rechargeable battery inside scale
NOTE:
The charging indicator is located on the left side of
scale and only will light up when charging.
Red color: Recharging battery
Green color: Charging completed

4. INITIAL SETUP
4.1 PLACING THE SCALE
In order to obtain an accurate weighing result, the scale
must be placed on a strong and level surface.
If required, adjust the adjustable feet underneath scale
to obtain a level position. Refer to the bubble indicator
for leveling condition.
4.2 INTERNAL SETTING
4.2.1 Display Segment Check
User can enter this function to check to see if the display
and backlight (if purchased) are functioning properly.
a. Scale is off
b. Press and hold TARE, then press ON/ZERO
c. Scale displays F.1
d. Press TAREonce
e. Scale displays F.2
f. Press MODE and all segments will light up to allow
user to check the condition of display
g. Press TARE for next function setup or ON/ZERO to
restart the scale

4.2.2 Select Auto Power Off Setting
The scale is equipped with Auto Power Off Function. The
scale will power off automatically if it is not used
for 4 minutes. Follow the below steps to enable/disable
Auto Power Off Function.
a. Scale is off
b. Press and hold TARE, then press ON/ZERO
c. Scale displays F.1
d. Press TARE three times
e. Scale displays F.4
f. Press MODE to shift between 0._OFF and 4._OFF
-To enable Auto Power Off Function, press TARE when
4._OFF appears
-To disable Auto Power Off Function, press TARE when
0._OFF appears
g. Press ON/ZERO to restart the scale or TARE for next
function setup
4.2.3 Select RS-232 Baud Rate & Protocol
This scale is equipped with 3 RS232C output baud rate
and 2 transmission protocol settings for user to select.
a. Scale is off
b. Press and hold TARE, then press ON/ZERO
c. Scale displays F.1

c. Press TARE four times
d. Scale displays F.5
e. Press MODE to select baud rate of 4800, 9600 and
19200
f. Press and hold MODE for 2 seconds to enter
transmission protocol setup
g. Press MODE to select protocol of N81 or E71
h. When the preferred transmission protocol shows on
display, press ON/ZERO to confirm and restart the
scale or TARE for next function setup
NOTE:
The default data output format of the scale is
Baud Rate = 9600
Data Bit = 8
Stop Bit = 1
Parity = None
4.2.4 Select Data Transmission Mode
This scale provides 2 types of transmission mode
depending on the requirement and environment.
a. Scale is off
b. Press and hold TARE, then press ON/ZERO
c. Scale displays F.1