V-Sol V2801RGW User manual

GPON 1GE+WiFi ONU Introduction_V1.1
1Access the world
Introduction
1.1 Product Description
GPON 1GE+WiFi ONU is support Dual mode(GPON), It can also be applied to a wide
temperature environment, good WiFi coverage and also has a powerful firewall function.
GPON 1GE+WiFi ONU meets telecom operators FTTO (office), FTTD (Desk),
FTTH(Home) broadband speed, SOHO broadband access, video surveillance and other
requirements and design a GPON Gigabit Ethernet products. The box is based on the mature
Gigabit GPON technology, highly reliable and easy to maintain, with guaranteed QOS for
different service. And it is fully compliant with technical regulations such as ITU-T G.984.x.
Figure 1 GPON 1GE+WiFi ONU
1.2 Product categories
Product model
Product specification
Chipset
SDRAM Memory
V2801RGW
1 GPON+1GE+WiFi
Realtek
64MB
Table 1 Product categories

GPON 1GE+WiFi ONU Introduction_V1.1
2Access the world
1.3 Application Chart
Figure 2 Application Chart
1.3 Technical parameters
Technical item
1GE+WiFi
PON interface
1 GPON port(GPON Class B+)
Wavelength:Tx1310nm,Rx 1490nm
SC/UPC connector
Receiving sensitivity: ≤-28dBm
Transmitting optical power: 0~+4dBm
Transmission distance: 20KM
LAN interface
1 x 10/100/1000Mbps auto adaptive Ethernet interfaces.10/100/1000M
Full/Half, RJ45 connector
WiFi interface
Compliant with IEEE802.11b/g/n
Operating frequency: 2.412-2.462GHz
support MIMO, rate up to 300Mbps
2T2R,2 external antenna 5dBi
Support: multiple SSID
Channel:13
LED
5, For Status of POWER、LOS、PON、LAN、WiFi
Operating
condition
Temperature: 0℃～+50℃
Humidity: 10%～90%（non-condensing）
Storing
condition
Temperature : -30℃～+60℃
Humidity :10%～90%（non-condensing）
Power supply
DC 12V/0.5A
Power
consumption
≤6W
EPON/GPON OLT

GPON 1GE+WiFi ONU Introduction_V1.1
3Access the world
Dimension
120mm×78mm×30mm（L×W×H）
Net weight
0.15Kg
Table 2 Technical parameters
1.4Panel lights
LED
Mark
Status
Description
Power
POWER
On
The device is powered up.
Off
The device is powered down.
Optical signal
loss
LOS
Blink
Device does not receive optical signals.
Off
Device has received optical signal.
Registration
REG
On
The device is registered to the PON system.
Off
Device is not registered to the PON system.
Blink
Device registration is incorrect.
Interface
LINK/ACT
On
Port is connected properly (LINK).
Off
Port connection exception or not connected.
Blink
Port is sending or/and receiving data (ACT).
WiFi
WiFi
On
WiFi running.
Off
WiFi not working.
Table 3 Panel lights on
1.6 Interface description
Port Type
Function
PON
Connect PON port with internet by SC/UPC type, single mode optical
fiber cable.
LAN
Connect device with ethernet port by RJ-45 cat5 cable.
RST
Press down reset button and keep1-5seconds to make the device
restart and recover from the factory default settings.
Power ON/OFF
Power on and Power off.
DC12V
Connect with power adapter.
Table 4 Interface description

GPON 1GE+WiFi ONU Introduction_V1.1
4Access the world
1.7 Software Key Feature
Software Key Feature
Software mode
Routing mode.
WiFi
IEEE802.11b/g/n
WiFi Authentication : WEP/WAP-PSK(TKIP)/WAP2-PSK(AES)
Layer3
IPv4, DHCP Client/Server , PPPoE,.
Multicast
IGMP v1/v2/v3 , IGMP snooping.
Security
Flow & Storm control, Loop Detection.
O&M
WEB/TELNET.
Table 5 Software Key Feature
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception,which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help
important announcement Important Note:
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed
and operated with minimum distance 20cm between the radiator and
your body.
This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.