Draytek Vigor130 User manual

Vigor130 Series User’s Guide
i

Vigor130 Series User’s Guide ii
Vigor130 Series
VDSL2/ADSL2/2+ Modem
User’s Guide
Version: 2.0
Firmware version: V3.8.5
(For future update, please visit DrayTek web site)
Date: June 1, 2022

Vigor130 Series User’s Guide
iii
Copyright Information
Copyright
Declarations © 2022 All rights reserved. This publication contains information that is protected by
copyright. No part may be reproduced, transmitted, transcribed, stored in a retrieval
system, or translated into any language without written permission from the copyright
holders.
Trademarks The following trademarks are used in this document:
Microsoft is a registered trademark of Microsoft Corp.
Windows 7, 8 and Explorer are trademarks of Microsoft Corp.
Apple and Mac OS are registered trademarks of Apple Inc.
Other products may be trademarks or registered trademarks of their respective
manufacturers.
Safety Instructions and Approval
Safety
Instructions
Read the installation guide thoroughly before you set up the modem.
The modem is a complicated electronic unit that may be repaired only be
authorized and qualified personnel. Do not try to open or repair the modem
yourself.
Do not place the modem in a damp or humid place, e.g. a bathroom.
The modem should be used in a sheltered area, within a temperature range of +5
to +40 Celsius.
Do not expose the modem to direct sunlight or other heat sources. The housing
and electronic components may be damaged by direct sunlight or heat sources.
Do not deploy the cable for LAN connection outdoor to prevent electronic shock
hazards.
Keep the package out of reach of children.
When you want to dispose of the modem, please follow local regulations on
conservation of the environment.
Warranty
We warrant to the original end user (purchaser) that the router will be free from any
defects in workmanship or materials for a period of two (2) years from the date of
purchase from the dealer. Please keep your purchase receipt in a safe place as it serves
as proof of date of purchase. During the warranty period, and upon proof of purchase,
should the product have indications of failure due to faulty workmanship and/or
materials, we will, at our discretion, repair or replace the defective products or
components, without charge for either parts or labor, to whatever extent we deem
necessary tore-store the product to proper operating condition. Any replacement will
consist of a new or re-manufactured functionally equivalent product of equal value, and
will be offered solely at our discretion. This warranty will not apply if the product is
modified, misused, tampered with, damaged by an act of God, or subjected to abnormal
working conditions. The warranty does not cover the bundled or licensed software of
other vendors. Defects which do not significantly affect the usability of the product will
not be covered by the warranty. We reserve the right to revise the manual and online
documentation and to make changes from time to time in the contents hereof without
obligation to notify any person of such revision or changes.

Vigor130 Series User’s Guide iv
T
Ta ab bl le e o of f C Co on nt te en nt ts s
Introduction .................................................................................................1
1.1 Web Configuration Buttons Explanation................................................................................. 1
1.2 LED Indicators and Connectors.............................................................................................. 2
1.3 Hardware Installation .............................................................................................................. 4
Basic Setup..................................................................................................5
2.1 Accessing Web Page.............................................................................................................. 5
2.2 Changing Password................................................................................................................ 6
2.3 Quick Start Wizard .................................................................................................................. 7
2.3.1 Setting PPPoE/PPPoA Connection.................................................................................. 7
2.3.2 Setting MPoA/Static or Dynamic Connection................................................................. 11
2.4 Introducing Dashboard.......................................................................................................... 14
2.4.1 Virtual Panel ................................................................................................................... 14
2.4.2 Name with a Link............................................................................................................ 15
2.4.3 Quick Access for Common Used Menu.......................................................................... 15
2.4.4 GUI Map ......................................................................................................................... 16
2.4.5 Web Console .................................................................................................................. 16
2.4.6 Config Backup ................................................................................................................ 18
2.5 Online Status......................................................................................................................... 19
2.5.1 Physical Connection.......................................................................................................19
2.5.2 Virtual WAN.................................................................................................................... 21
2.6 Saving Configuration............................................................................................................. 22
2.7 Registering Vigor130............................................................................................................. 22
Web Configuration ....................................................................................27
3.1 Internet Access...................................................................................................................... 27
3.1.1 Basics of Internet Protocol (IP) Network......................................................................... 27
3.1.2 General Setup................................................................................................................. 28
3.1.3 PPPoE/PPPoA................................................................................................................ 29
3.1.4 MPoA /Static or dynamic IP............................................................................................ 32
3.1.5 IPv6................................................................................................................................. 35
3.1.6 Multi-PVC/VLAN............................................................................................................. 43
3.2 LAN ....................................................................................................................................... 48
3.2.1 Basics of LAN................................................................................................................. 48
3.2.2 General Setup................................................................................................................. 50
3.2.3 Static Route.................................................................................................................... 55
3.2.4 Bind IP to MAC............................................................................................................... 59

Vigor130 Series User’s Guide
v
3.3 NAT ....................................................................................................................................... 61
3.3.1 Port Redirection.............................................................................................................. 62
3.3.2 DMZ Host........................................................................................................................ 65
3.3.3 Open Ports...................................................................................................................... 68
3.3.4 ALG................................................................................................................................. 70
3.4 Firewall.................................................................................................................................. 71
3.4.1 Basics for Firewall........................................................................................................... 71
3.4.2 General Setup................................................................................................................. 73
3.4.3 Filter Setup ..................................................................................................................... 77
3.4.4 DoS Defense .................................................................................................................. 83
3.5 Objects Settings.................................................................................................................... 87
3.5.1 IP Object......................................................................................................................... 87
3.5.2 IP Group ......................................................................................................................... 89
3.5.3 IPv6 Object..................................................................................................................... 91
3.5.4 IPv6 Group...................................................................................................................... 93
3.5.5 Service Type Object .......................................................................................................94
3.5.6 Service Type Group........................................................................................................96
3.5.7 Keyword Object .............................................................................................................. 98
3.5.8 Keyword Group.............................................................................................................100
3.5.9 File Extension Object.................................................................................................... 101
3.6 CSM Profile......................................................................................................................... 102
3.6.1 URL Content Filter Profile............................................................................................. 103
3.7 Applications......................................................................................................................... 107
3.7.1 Dynamic DNS...............................................................................................................107
3.7.2 Schedule....................................................................................................................... 110
3.7.3 UPnP............................................................................................................................. 113
3.7.4 IGMP............................................................................................................................. 115
3.8 System Maintenance............................................................................................................117
3.8.1 System Status............................................................................................................... 117
3.8.2 TR-069.......................................................................................................................... 119
3.8.3 Administrator Password................................................................................................ 120
3.8.4 Configuration Backup ................................................................................................... 121
3.8.5 Syslog/Mail Alert........................................................................................................... 123
3.8.6 Time and Date.............................................................................................................. 125
3.8.7 Management................................................................................................................. 126
3.8.8 Self-Signed Certificate.................................................................................................. 130
3.8.9 Reboot System.............................................................................................................131
3.8.10 Firmware Upgrade...................................................................................................... 133
3.9 Diagnostics.......................................................................................................................... 134
3.9.1 Dial-out Triggering........................................................................................................ 134
3.9.2 Routing Table ............................................................................................................... 135
3.9.3 ARP Cache Table......................................................................................................... 136
3.9.4 IPv6 Neighbour Table................................................................................................... 136
3.9.5 DHCP Table.................................................................................................................. 137
3.9.6 NAT Sessions Table..................................................................................................... 138
3.9.7 DNS Cache Table......................................................................................................... 139
3.9.8 Ping Diagnosis.............................................................................................................. 140
3.9.9 Data Flow Monitor.........................................................................................................141
3.9.10 Trace Route................................................................................................................ 143
3.9.11 IPv6 TSPC Status....................................................................................................... 144
3.9.12 DSL Status.................................................................................................................. 145

Vigor130 Series User’s Guide vi
Application and Examples.......................................................................147
4.1 LAN – Created by Using NAT ............................................................................................. 147
Trouble Shooting......................................................................................151
5.1 Checking If the Hardware Status Is OK or Not.................................................................... 151
5.2 Checking If the Network Connection Settings on Your Computer Is OK or Not ................. 152
5.3 Pinging the Modem from Your Computer............................................................................ 155
5.4 Checking If the ISP Settings are OK or Not........................................................................ 156
5.5 Backing to Factory Default Setting If Necessary ................................................................ 156
5.6 Contacting DrayTek............................................................................................................. 157
Telnet Command Reference..........................................................................................159
Accessing Telnet of Vigor130....................................................................................................159
Telnet Command: adsl txpct /adsl rxpct ................................................................................ 159
Telnet Command: adsl status................................................................................................ 160
Telnet Command: adsl ppp.................................................................................................... 160
Telnet Command: adsl bridge................................................................................................ 162
Telnet Command: adsl idle.................................................................................................... 163
Telnet Command: adsl drivemode......................................................................................... 163
Telnet Command: adsl reboot ............................................................................................... 163
Telnet Command: adsl oamlb................................................................................................ 164
Telnet Command: adsl vcilimit............................................................................................... 164
Telnet Command: adsl annex................................................................................................ 165
Telnet Command: adsl automode ......................................................................................... 165
Telnet Command: adsl showbins........................................................................................... 165
Telnet Command: adsl optn................................................................................................... 166
Telnet Command: adsl femec................................................................................................ 167
Telnet Command: adsl savecfg............................................................................................. 167
Telnet Command: adsl vendorid............................................................................................ 167
Telnet Command: adsl atm.................................................................................................... 168
Telnet Command: adsl pvcbinding ........................................................................................ 168
Telnet Command: vdsl status................................................................................................ 169
Telnet Command: vdsl idle.................................................................................................... 169
Telnet Command: vdsl drivermode........................................................................................ 170
Telnet Command: vdsl reboot................................................................................................ 170
Telnet Command: vdsl annex................................................................................................ 170
Telnet Command: vdsl showbins........................................................................................... 171
Telnet Command: vdsl optn................................................................................................... 171
Telnet Command: vdsl savecfg ............................................................................................. 172
Telnet Command: vdsl vendorid............................................................................................ 172
Telnet Command: vdsl snr..................................................................................................... 172
Telnet Command: bpa........................................................................................................... 173
Telnet Command: csm appe prof.......................................................................................... 173
Telnet Command: csm appe p2p .......................................................................................... 175
Telnet Command: csm appe misc......................................................................................... 176
Telnet Command: csm ucf..................................................................................................... 177
Telnet Command: csm ucf obj INDEX uac............................................................................ 178
Telnet Command: csm ucf obj INDEX wf.............................................................................. 180

Vigor130 Series User’s Guide
vii
Telnet Command: csm wcf.................................................................................................... 181
Telnet Command: ddns log.................................................................................................... 183
Telnet Command: ddns time.................................................................................................. 183
Telnet Command: dos ........................................................................................................... 184
Telnet Command: exit............................................................................................................185
Telnet Command: Internet..................................................................................................... 185
Telnet Command: ip 2ndsubnet............................................................................................. 186
Telnet Command: ip 2ndaddr................................................................................................ 186
Telnet Command: ip 2ndmask............................................................................................... 187
Telnet Command: ip aux........................................................................................................ 187
Telnet Command: ip addr...................................................................................................... 188
Telnet Command: ip nmask................................................................................................... 189
Telnet Command: ip arp........................................................................................................ 189
Telnet Command: ip dhcpc.................................................................................................... 190
Telnet Command: ip ping....................................................................................................... 191
Telnet Command: ip tracert................................................................................................... 191
Telnet Command: ip telnet..................................................................................................... 192
Telnet Command: ip rip ......................................................................................................... 192
Telnet Command: ip wanrip................................................................................................... 193
Telnet Command: ip route..................................................................................................... 194
Telnet Command: ip igmp_proxy........................................................................................... 195
Telnet Command: ip wanaddr................................................................................................ 196
Telnet Command: ip wanttr.................................................................................................... 196
Telnet Command: ip dmz....................................................................................................... 196
Telnet Command: ip session................................................................................................. 197
Telnet Command: ip bandwidth............................................................................................. 198
Telnet Command: ip bindmac................................................................................................ 199
Telnet Command: ip maxnatuser........................................................................................... 200
Telnet Command: ip6 addr.................................................................................................... 200
Telnet Command: ip6 dhcp req_opt...................................................................................... 201
Telnet Command: ip6 dhcp client.......................................................................................... 201
Telnet Command: ip6 dhcp server ........................................................................................ 202
Telnet Command: ip6 internet ............................................................................................... 204
Telnet Command: ip6 neigh................................................................................................... 205
Telnet Command: ip6 pneigh................................................................................................. 206
Telnet Command: ip6 route................................................................................................... 206
Telnet Command: ip6 ping..................................................................................................... 207
Telnet Command: ip6 tracert................................................................................................. 208
Telnet Command: ip6 tspc..................................................................................................... 208
Telnet Command: ip6 radvd .................................................................................................. 209
Telnet Command: ip6 mngt ................................................................................................... 209
Telnet Command: ip6 online.................................................................................................. 210
Telnet Command: ip6 aiccu................................................................................................... 211
Telnet Command: ip6 ntp ...................................................................................................... 212
Telnet Command: ipf view..................................................................................................... 212
Telnet Command: ipf set........................................................................................................ 213
Telnet Command: ipf flowtrack.............................................................................................. 214
Telnet Command: Log........................................................................................................... 215
Telnet Command: mngt ftpport.............................................................................................. 216
Telnet Command: mngt httpport............................................................................................ 217
Telnet Command: mngt httpsport.......................................................................................... 217
Telnet Command: mngt telnetport......................................................................................... 217
Telnet Command: mngt sshport ............................................................................................ 218
Telnet Command: mngt ftpserver.......................................................................................... 218
Telnet Command: mngt noping ............................................................................................. 218
Telnet Command: mngt defenseworm .................................................................................. 220
Telnet Command: mngt rmtcfg.............................................................................................. 220
Telnet Command: mngt echoicmp......................................................................................... 221
Telnet Command: mngt accesslist ........................................................................................ 221
Telnet Command: mngt snmp ............................................................................................... 222

Vigor130 Series User’s Guide viii
Telnet Command: object ip obj.............................................................................................. 223
Telnet Command: object ip grp.............................................................................................. 224
Telnet Command: object service obj..................................................................................... 225
Telnet Command: object service grp..................................................................................... 227
Telnet Command: object kw.................................................................................................. 228
Telnet Command: object fe.................................................................................................... 229
Telnet Command: port........................................................................................................... 231
Telnet Command: portmaptime............................................................................................. 231
Telnet Command: qos setup.................................................................................................. 232
Telnet Command: qos class.................................................................................................. 234
Telnet Command: qos type.................................................................................................... 235
Telnet Command: quit ........................................................................................................... 236
Telnet Command: show lan1................................................................................................. 236
Telnet Command: show lan2................................................................................................. 236
Telnet Command: show dhcp................................................................................................ 236
Telnet Command: show dmz................................................................................................. 237
Telnet Command: show dns.................................................................................................. 237
Telnet Command: show openport ......................................................................................... 237
Telnet Command: show nat................................................................................................... 237
Telnet Command: show portmap........................................................................................... 238
Telnet Command: show pmtime............................................................................................ 238
Telnet Command: show session............................................................................................ 238
Telnet Command: show status.............................................................................................. 238
Telnet Command: show adsl................................................................................................. 239
Telnet Command: show statistic............................................................................................ 239
Telnet Command: srv nat dmz............................................................................................... 249
Telnet Command: sys cfg...................................................................................................... 253
Telnet Command: sys cmdlog............................................................................................... 254
Telnet Command: sys ftpd..................................................................................................... 254
Telnet Command: sys domainname...................................................................................... 254
Telnet Command: sys iface................................................................................................... 256
Telnet Command: sys name.................................................................................................. 257
Telnet Command: sys passwd............................................................................................... 257
Telnet Command: sys reboot................................................................................................. 257
Telnet Command: sys autoreboot ......................................................................................... 258
Telnet Command: sys commit............................................................................................... 258
Telnet Command: sys tftpd.................................................................................................... 258
Telnet Command: sys cc....................................................................................................... 258
Telnet Command: sys version............................................................................................... 259
Telnet Command: sys qrybuf................................................................................................. 259
Telnet Command: sys pollbuf................................................................................................ 259
Telnet Command: sys britask................................................................................................ 261
Telnet Command: sys tr069................................................................................................... 261
Telnet Command: sys sip_alg ............................................................................................... 263
Telnet Command: sys license................................................................................................ 263
Telnet Command: sys diag_log............................................................................................. 264
Telnet Command: testmail..................................................................................................... 266
Telnet Command: upnp off.................................................................................................... 266
Telnet Command: upnp on.................................................................................................... 266
Telnet Command: upnp nat................................................................................................... 266
Telnet Command: upnp service............................................................................................. 267
Telnet Command: upnp subscribe......................................................................................... 267
Telnet Command: upnp tmpvs............................................................................................... 268
Telnet Command: upnp wan.................................................................................................. 269
Telnet Command: vigbrg on .................................................................................................. 269
Telnet Command: vigbrg off .................................................................................................. 269
Telnet Command: vigbrg status............................................................................................. 269
Telnet Command: vigbrg cfgip............................................................................................... 270
Telnet Command: vigbrg wan1on.......................................................................................... 270
Telnet Command: vigbrg wan1off.......................................................................................... 270

Vigor130 Series User’s Guide
ix
Telnet Command: wan ppp_mru ........................................................................................... 270
Telnet Command: wan mtu.................................................................................................... 271
Telnet Command: wan DF_check ......................................................................................... 271
Telnet Command: wan disable.............................................................................................. 272
Telnet Command: wan enable............................................................................................... 272
Telnet Command: wan forward.............................................................................................. 272
Telnet Command: wan status................................................................................................ 272
Telnet Command: wan vdsl................................................................................................... 273
Telnet Command: wan detect................................................................................................ 274
Telnet Command: wan lb....................................................................................................... 275
Telnet Command: wan mvlan................................................................................................ 275
Telnet Command: wan multifno............................................................................................. 277
Telnet Command: wan vlan................................................................................................... 278

Vigor130 Series User’s Guide
1
I In nt tr ro od du uc ct ti io on n
Vigor130 Series is a VDSL2/ADSL2/2+ modem.
The object-based design used in SPI (Stateful Packet Inspection) firewall allows users to set
firewall policy with ease. It is flexible and makes your network be safe. By the way,
DoS/DDoS prevention and URL content filter strengthen the security outside and control
inside.
1
1. .1 1 W We eb b C Co on nf fi ig gu ur ra at ti io on n B Bu ut tt to on ns s E Ex xp pl la an na at ti io on n
Several main buttons appeared on the web pages are defined as the following:
Save and apply current settings.
Cancel current settings and recover to the previous saved settings.
Clear all the selections and parameters settings, including selection from
drop-down list. All the values must be reset with factory default settings.
Add new settings for specified item.
Edit the settings for the selected item.
Delete the selected item with the corresponding settings.
Note: For the other buttons shown on the web pages, please refer to Chapter 4 for detailed
explanation.

Vigor130 Series User’s Guide 2
1
1. .2 2 L LE ED D I In nd di ic ca at to or rs s a an nd d C Co on nn ne ec ct to or rs s
Before you use the Vigor modem, please get acquainted with the LED indicators and
connectors first.
LED Status Explanation
Off The system is not ready or is failed.ACT Blinking The system is ready and can work normally.
On A normal connection is through its corresponding
port.
Off LAN is disconnected.
LAN
Blinking Data is transmitting (sending/receiving).
On The DoS/DDoS function is active.DoS Blinking It will blink while detecting an attack.
On DSL connection synchronized.DSL Blinking DSL connection is synchronizing.

Vigor130 Series User’s Guide
3
Interface Description
DSL Connecter for accessing the Internet through VDSL2/ADSL2/2+.
LAN Connecter for local networked devices.
Factory Reset Restore the default settings.
Usage: Turn on the modem. Press the button and keep for more than 10
seconds. Then the modem will restart with the factory default
configuration.
ON/OFF: Power switch.
Connecter for a power adapter.

Vigor130 Series User’s Guide 4
1
1. .3 3 H Ha ar rd dw wa ar re e I In ns st ta al ll la at ti io on n
This section will guide you to install the modem through hardware connection and configure
the modem’s settings through web browser.
Before starting to configure the modem, you have to connect your devices correctly.
1. Connect the DSL interface to the MODEM port of external splitter with a DSL line
cable.
2. Connect the LAN port to your computer with a RJ-45 cable.
3. Connect one end of the power adapter to the Power port of this device. Connect the
other end to the wall outlet of electricity.
4. Power on the modem.
5. Check the POWER, ACT, LAN, DSL and INTERNET LEDs to assure network
connections.
(For the detailed information of LED status, please refer to section 1.2.)

Vigor130 Series User’s Guide
5
B Ba as si ic c S Se et tu up p
For using the modem properly, it is necessary for you to change the password of web
configuration for security and adjust primary basic settings.
2
2. .1 1 A Ac cc ce es ss si in ng g W We eb b P Pa ag ge e
1. Make sure your PC connects to the modem correctly.
Notice: You may either simply set up your computer to get IP dynamically
from the modem or set up the IP address of the computer to be the same subnet
as the default IP address of Vigor modem 192.168.1.1. For the detailed
information, please refer to the later section - Trouble Shooting of the guide.
2. Open a web browser on your PC and type http://192.168.1.1. A pop-up window will
open to ask for username and password. Please type “admin/admin” as the username
and password. Then click Login.
Notice: If you fail to access to the web configuration, please go to “Trouble
Shooting” for detecting and solving your problem.

Vigor130 Series User’s Guide 6
2
2. .2 2 C Ch ha an ng gi in ng g P Pa as ss sw wo or rd d
Please change the password for the original security of the modem.
1. Access into the web user interface of Vigor130. The Main Screen will appear as
below.
2. Go to System Maintenance page and choose Administrator Password/User
Password.
3. Enter the login password (the default is blank) on the field of Old Password. Type
New Password. Then click OK to continue.
4. Now, the password has been changed. Next time, use the new password to access the
Web User Interface for this modem.

Vigor130 Series User’s Guide
7
2
2. .3 3 Q Qu ui ic ck k S St ta ar rt t W Wi iz za ar rd d
Notice: Quick Start Wizard for user operation is the same as for administrator’s
operation.
The configuration provide here can help you to deploy and use the modem quickly.
2
2. .3 3. .1 1 S Se et tt ti in ng g P PP PP Po oE E/ /P PP PP Po oA A C Co on nn ne ec ct ti io on n
PPPoE stands for Point-to-Point Protocol over Ethernet. It relies on two widely accepted
standards: PPP and Ethernet. It connects users through an Ethernet to the Internet with a
common broadband medium, such as a single DSL line, wireless device or cable modem. All
the users over the Ethernet can share a common connection.
PPPoE is used for most of DSL modem users. All local users can share one PPPoE
connection for accessing the Internet. Your service provider will provide you information
about user name, password, and authentication mode.
If your ISP provides you the PPPoE connection, please select PPPoE for this modem.
1. Click Quick Start wizard.
2. The first screen of Quick Start Wizard is entering login password of the web user
interface. After typing the password, please click Next.

Vigor130 Series User’s Guide 8
3. On the next page, please select the WAN interface (at present, only WAN1 is available)
that you use and specify the DSL mode.
4. You can configure the modem to access the Internet with different protocol/modes such
as PPPoE/PPPoA or MPoA/Static or Dynamic IP. The modem supports the ADSL
WAN interface for Internet access. In this case, choose PPPoE/PPPoA.
Available parameters are listed below:
I
It te em m D De es sc cr ri ip pt ti io on n
F
Fo or r A AD DS SL L O On nl ly y Y
Yo ou u h ha av ve e t to o s se el le ec ct t a an n a ap pp pr ro op pr ri ia at te e W WA AN N c co on nn ne ec ct ti io on n t ty yp pe e f fo or r
c
co on nn ne ec ct ti in ng g t to o t th he e I In nt te er rn ne et t t th hr ro ou ug gh h t th hi is s m mo od de em m a ac cc co or rd di in ng g t to o
t
th he e s se et tt ti in ng gs s t th ha at t y yo ou ur r I IS SP P p pr ro ov vi id de ed d. .
A
Au ut to o d de et te ec ct t – – C Cl li ic ck k i it t t to o d de et te ec ct t s su ui it ta ab bl le e v va al lu ue es s b be el lo ow w b by y t th he e
m
mo od de em m a au ut to om ma at ti ic ca al ll ly y. .

Vigor130 Series User’s Guide
9
I
It te em m D De es sc cr ri ip pt ti io on n
E
En nc ca ap ps su ul la at ti io on n S
Se el le ec ct t a an n I IP P m mo od de e f fo or r t th hi is s W WA AN N i in nt te er rf fa ac ce e. . T Th he er re e a ar re e s se ev ve er ra al l
a
av va ai il la ab bl le e m mo od de es s f fo or r I In nt te er rn ne et t a ac cc ce es ss s s su uc ch h a as s P PP PP Po oE E, ,
P
PP PP Po oA A. .
V
VP PI I S
St ta an nd ds s f fo or r V Vi ir rt tu ua al l P Pa at th h I Id de en nt ti if fi ie er r. . I It t i is s a an n 8 8- -b bi it t h he ea ad de er r
i
in ns si id de e e ea ac ch h A AT TM M c ce el ll l t th ha at t i in nd di ic ca at te es s w wh he er re e t th he e c ce el ll l s sh ho ou ul ld d
b
be e r ro ou ut te ed d. . T Th he e A AT TM M, , i is s a a m me et th ho od d o of f s se en nd di in ng g d da at ta a i in n s sm ma al ll l
p
pa ac ck ke et ts s o of f f fi ix xe ed d s si iz ze es s. . I It t i is s u us se ed d f fo or r t tr ra an ns sf fe er rr ri in ng g d da at ta a t to o
c
cl li ie en nt t c co om mp pu ut te er rs s. .
V
VC CI I S
St ta an nd ds s f fo or r V Vi ir rt tu ua al l C Ch ha an nn ne el l I Id de en nt ti if fi ie er r. . I It t i is s a a 1 16 6- -b bi it t f fi ie el ld d
i
in ns si id de e A AT TM M c ce el ll l’ ’s s h he ea ad de er r t th ha at t i in nd di ic ca at te es s t th he e c ce el ll l’ ’s s n ne ex xt t
d
de es st ti in na at ti io on n a as s i it t t tr ra av ve el ls s t th hr ro ou ug gh h t th he e n ne et tw wo or rk k. . A A v vi ir rt tu ua al l
c
ch ha an nn ne el l i is s a a l lo og gi ic ca al l c co on nn ne ec ct ti io on n b be et tw we ee en n t tw wo o e en nd d d de ev vi ic ce es s o on n
t
th he e n ne et tw wo or rk k. .
F
Fi ix xe ed d I IP P C
Cl li ic ck k Y Ye es s t to o s sp pe ec ci if fy y a a f fi ix xe ed d I IP P f fo or r t th he e m mo od de em m. . O Ot th he er rw wi is se e, ,
c
cl li ic ck k N No o ( (D Dy yn na am mi ic c I IP P) ) t to o a al ll lo ow w t th he e m mo od de em m c ch ho oo os si in ng g a a
d
dy yn na am mi ic c I IP P. . I If f y yo ou u c ch ho oo os se e N No o, , t th he e f fo ol ll lo ow wi in ng g I IP P A Ad dd dr re es ss s, ,
S
Su ub bn ne et t M Ma as sk k a an nd d D De ef fa au ul lt t G Ga at te ew wa ay y w wi il ll l n no ot t b be e c ch ha an ng ge ed d. .
I
IP P A Ad dd dr re es ss s A
As ss si ig gn n a an n I IP P a ad dd dr re es ss s f fo or r t th he e p pr ro ot to oc co ol l t th ha at t y yo ou u s se el le ec ct t. .
S
Su ub bn ne et t M Ma as sk k A
As ss si ig gn n a a s su ub bn ne et t m ma as sk k v va al lu ue e f fo or r t th he e p pr ro ot to oc co ol l o of f
M
MP Po oA A/ /S St ta at ti ic c o or r D Dy yn na am mi ic c I IP P. .
D
De ef fa au ul lt t G Ga at te ew wa ay y A
As ss si ig gn n a an n I IP P a ad dd dr re es ss s t to o t th he e g ga at te ew wa ay y f fo or r t th he e p pr ro ot to oc co ol l o of f
M
MP Po oA A/ /S St ta at ti ic c o or r D Dy yn na am mi ic c I IP P. .
P
Pr ri im ma ar ry y D DN NS S A
As ss si ig gn n a an n I IP P a ad dd dr re es ss s t to o t th he e p pr ri im ma ar ry y D DN NS S. .
S
Se ec co on nd d D DN NS S A
As ss si ig gn n a an n I IP P a ad dd dr re es ss s t to o t th he e s se ec co on nd da ar ry y D DN NS S. .
V
VL LA AN N T Ta ag g i in ns se er rt ti io on n D
De et te er rm mi in ne es s w wh he et th he er r 8 80 02 2. .1 1a ad d V VL LA AN N t ta ag gs s w wi il ll l b be e a ad dd de ed d t to o
o
ou ut tb bo ou un nd d W WA AN N t tr ra af ff fi ic c i in n A AD DS SL L/ /V VD DS SL L 2 2 m mo od de e. . C Ch he ec ck k
w
wi it th h y yo ou ur r I IS SP P t to o d de et te er rm mi in ne e i if f t th hi is s i is s r re eq qu ui ir re ed d, , a an nd d i if f s so o, , t th he e
p
pr ro op pe er r t ta ag g a an nd d p pr ri io or ri it ty y v va al lu ue es s t to o b be e u us se ed d. .
E
En na ab bl le ed d - - T Ta ag gg gi in ng g e en na ab bl le ed d. .
D
Di is sa ab bl le ed d - - T Ta ag gg gi in ng g d di is sa ab bl le ed d. .
T
Ta ag g v va al lu ue e - -V Va al lu ue e m mu us st t b be e b be et tw we ee en n 1 1 a an nd d 4 40 09 95 5. .
P
Pr ri io or ri it ty y - - P Pr ri io or ri it ty y c co od de e p po oi in nt t ( (P PC CP P) ). . V Va al lu ue e m mu us st t b be e
b
be et tw we ee en n 0 0 a an nd d 7 7. .
5. After finished the above settings, click Next to access into next page.

Vigor130 Series User’s Guide 10
Available parameters are listed below:
I
It te em m D De es sc cr ri ip pt ti io on n
U
Us se er r N Na am me e A
As ss si ig gn n a a s sp pe ec ci if fi ic c v va al li id d u us se er r n na am me e p pr ro ov vi id de ed d b by y t th he e I IS SP P. . I It t
w
wi il ll l b be e u us se ed d t to o a ac cc ce es ss s I In nt te er rn ne et t. .
P
Pa as ss sw wo or rd d A
As ss si ig gn n a a v va al li id d p pa as ss sw wo or rd d p pr ro ov vi id de ed d b by y t th he e I IS SP P. . I It t w wi il ll l b be e
u
us se ed d t to o a ac cc ce es ss s I In nt te er rn ne et t. .
C
Co on nf fi ir rm m P Pa as ss sw wo or rd d R
Re et ty yp pe e t th he e p pa as ss sw wo or rd d. .
6. Click Next for viewing summary of such connection.
7. Click Finish. The Quick Start Wizard Setup OK page will be displayed.