V-TAC VT-8055 User manual

In case of any query/issue with the product, please reach out to us at: [e-mail]
For More products range, inquiry please contact our distributor or nearest dealers.
V-TAC EUROPE LTD. Bulgaria, Plovdiv 4000, bul.L.Karavelow 9B
MULTI-LANGUAGE MANUAL QR CODE
Please scan the QR code to
access the manual in multiple languages.
INSTRUCTION MANUAL
LANDSCAPE SOFT LIGHT
OUTDOOR
INTRODUCTION & WARRANTY
Thank you for selecting and buying V-TAC product. V-TAC will serve you the best. Please read these instructions
carefully before starting the installation and keep this manual handy for future reference. If you have any another
query, please contact our dealer or local vendor from whom you have purchased the product. They are trained
and ready to serve you at the best. The warranty is valid for 2 years from the date of purchase. The warranty
does not apply to damage caused by incorrect installation or abnormal wear and tear. The company gives no
warranty against damage to any surface due to incorrect removal and installation of the product. The products
are suitable for 10-12 Hours Daily operation. Usage of product for 24 Hours a day would void the warranty. This
product is warranted for manufacturing defects only.
TECHNICAL DATA
MODEL VT-8055
SKU 218236, 218237,
218238
LUMENS
2045 Lm
In Sphere
(360°)
2050 Lm
In Sphere
(360°)
WATTS 20W
BEAM ANGLE 110°
CRI ≥80
INPUT VOLTAGE AC: 220-240V,
50/60Hz
ON/OFF CYCLE 15,000
LIFE SPAN 20,000 Hours
MATERIAL PC
DIMENSION 319x170x114

This marking indicates that this
product should not be disposed of
with other household wastes.
WARNING
1. Please make sure to turn o the power before starting the installation.
2. Installation must be performed by a qualified electrician.
3. If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively
replaced by the manufacturer or his service agent or a similar qualified person in order
to avoid a hazard.
4. NOTE: Mercury is not present.
Caution, risk of electric shock.
Rubber Pluy
Rubber Ring
Rubber Ring
Base
Sub-Tapping Screws
LED
Sub-Tapping Screws
Rubber Ring
Lamp Shade
Screw
Shell
319 114
170
Terminal
PRODUCT DIAGRAM
Replaceable (LED Only) light
source by a professional
Replaceable control gear
by a professional

1. Switch o the power.
2. To drill the appropriate holes on the wall. (picture 1)
3. Enter the particles and install the lamp base on the wall. (picture 2)
4. Connect the light into the mains (220-240V, 50/60Hz), install the lampshade
and cover the shell. (picture 3)
5. Switch on the power if above steps are done properly without any mistakes.
INSTALLATION DIAGRAM
1 2
3

STEPS TO REMOVE THE LIGHT SOURCE FOR VERIFICATION
(ONLY FOR MARKET SURVEILLANCE AUTHORITY)
Note: Light Source Removal will Void the Warranty
STEPS
RECOMMENDATIONS ON HOW TO DISPOSE THE LIGHT
SOURCE AT THE END OF ITS LIFE:
1. Remove the lamp shell with your hands or a screwdriver
2. Unscrew the lamp shade with a screwdriver and take o the lamp shade
3. Unscrew the sub-tapping screws and take out the LED. Mains connection test.
1. Electrical and electronic equipment that has become waste is known as old equipment/device.
Old devices must not be disposed of with other household waste.
2. Owners of old devices at the end of its service life must return the device by taking them to the
collection points set up by public waste disposal authorities or distributors. This return does not
entail any costs for you.
3. Owners of old devices have an obligation to remove lamps non-destructively from the old device
prior to return.
4. The symbol of “Crossed rubbish bins “indicates that this product should not be disposed of with
other household wastes and must be collected separately from unsorted municipal waste at the
end of its service life.
5. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into
the groundwater and get into the food chain, damaging your health and well-being.