Vacmaster VMVDK1538SWC-06 User manual

VDK1538SWC
38L 1500W
ORIGINAL INSTRUCTIONS

16
15
12
13
14
17
25
31 32 33 34
26 27 28 29 30
20 21 22 23 2418
6
1
2
4
3
5
10
11
9
8
7
19

6
TABLE OF CONTENTS
SECTION PAGE
Symbols............................................................................................................................................ 6
Safety Information ............................................................................................................................ 7
Unpacking and Checking Carton Contents .................................................................................... 10
Assembly.........................................................................................................................................11
Operation........................................................................................................................................ 12
Maintenance................................................................................................................................... 15
Troubleshooting.............................................................................................................................. 16
Technical Data ................................................................................................................................ 17
Recycling and Disposal .................................................................................................................. 17
Thank you for purchasing this Vacmaster® wet and dry vacuum cleaner. Feel condent that with
Vacmaster®you are obtaining a high quality product engineered for optimal performance. This
vacuum cleaner is suitable for use with both liquids and dry materials.
FOR YOUR SAFETY: CAREFULLY READ AND UNDERSTAND ALL INSTRUCTIONS.
SYMBOLS
Caution
Read instruction manual. Failure to follow the warnings and
instructions may result in electric shock, re and/or serious injury.
Vacuum cleaners of dust category M according to IEC/EN 60335-2-69
for dry vacuuming of hazardous dusts with an exposition limit value
≥0.1 mg/m
3
.
WARNING: The vacuum cleaner may contain materials that are
hazardous to one's health. Have the emptying and maintenance,
incl. the disposal of dust-collection container, carried out only
by a specialist. Appropriate protective equipment is required.
Do not operate the vacuum cleaner without the complete lter
system. Otherwise there is danger to your own health.

7
SAFETY INFORMATION
READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE
USING THIS VACUUM CLEANER.
This machine is intended for commercial use, for example in
hotels, schools, hospitals, factories, shops, ofces and rental
businesses. Any other use is considered as improper use. The
manufacturer accepts no liability for any damage resulting from
improper use. The risk for such improper use is borne solely by
the user.
When using the equipment, a few safety precautions must be
observed to avoid injuries and damage. Please read the complete
operating manual with due care. Keep this manual in a safe
place so that the information is always available. If you give
the equipment to any other person, give them these operating
instructions as well. We cannot accept any liability for damage or
accidents which arise due to a failure to follow these instructions
and the safety information.
• Never leave the appliance switched on unattended, if you leave
the work area, switch the appliance off or unplug it from the
power supply.
• Do not vacuum or use this vacuum cleaner near ammable
liquids, gases or explosive vapours like gasoline or other fuels,
lighter uids, cleaners, oil-based paints, natural gas, hydrogen,
or explosive dusts like coal dust, magnesium dust, grain dust
or gun power. Sparks inside the motor can ignite ammable
vapours or dust.
• This vacuum cleaner is not suitable for the vacuuming of
asbestos or asbestos dust.
• Do not vacuum anything that is burning or smoking, such as
cigarettes, matches, or hot ashes.
• Ensure the hose and connections are always pointed away
from the users face, hair, ears and eyes during operation and
never direct the nozzle towards persons or animals.

8
• Clear the working area of any items or possessions that you do
not wish to be vacuumed before operation.
• Keep cord away from heated surfaces.
• Do not expose to rain. Store indoors.
• Do not unplug by pulling on the cord. To unplug, grasp the plug,
not the cord.
• Do not use with damaged cord, plug or other parts.
• Do not pull or carry by cord, use cord as handle, close a door
on cord, or pull cord around sharp edges or corners.
• Do not handle the plug or vacuum cleaner with wet hands.
• Frequently check that the oat valve positioned underneath the
motor is able to move freely.
• Do not use this vacuum cleaner with a torn lter or without the
lter installed.
• Do not allow to be used as a toy. Close attention is necessary
when used by or near children.
• To reduce the risk of injury from accidental starting, unplug
power cord before changing or cleaning lter.
• Unplug from power supply when not in use and before carrying
out maintenance.
• Do not cover the ventilation openings. Do not vacuum with any
ventilation openings blocked; keep free of dust, lint, hair or
anything that may reduce air ow.
• Keep hair, loose clothing, ngers, all parts of body away from
openings and moving parts.
• If the supply cord is damaged, it must be replaced by the
manufacturer, a qualied service agent or similarly qualied
persons in order to avoid a hazard.
• This machine is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge.
• Children shall not play with the appliance.
• Cleaning and user maintenance shall not be made by children
without supervision.
• For additional protection: It is recommended that this vacuum
cleaner can be used in conjunction with residual current device
(RCD) with a rated residual current of 30mA or less.
• Only use the socket outlet on the machine for purposes

9
specied in the instructions.
• If foam or liquid escapes from the machine, switch off immediately.
• Check the oat valve regularly to ensure it is moving freely and
examine it for signs of damage.
• Precautions should be taken when changing attachments.
• For user servicing, the machine must be dismantled, cleaned
and serviced, as far as is reasonably practicable, without
causing risk to the maintenance staff and others. Suitable
precautions include decontamination before dismantling,
provision for local ltered exhaust ventilation where the
machine is dismantled, cleaning of the maintenance area and
suitable personal protection.
• Perform a technical inspection at least annually, consisting of,
for example, inspection of lters for damage, air tightness of the
machine and proper function of the control mechanism.
• Besides the operating instructions and the binding accident
prevention regulations valid in the country of use, observe
recognized regulations for safety and proper use.
• When dust removers are used, the rate at which air is
exchanged in the room must be adequate if the exhaust
air from the vacuum cleaner is blown into the room (please
observe regulations valid in your country).
• Before starting work, the operating staff must be informed on
- use of the vacuum cleaner
- risks associated with the material to be picked up
- safe disposal of the picked up material.
• Before transporting the collection tank, close all the locks. Do
not tilt the cleaner if there is liquid in the collection tank. Do not
use a crane hook to lift the cleaner.
• For class M machines, the outside of the machine should be
decontaminated and wiped clean or treated with sealant before
being taken out of a hazardous area. All the machine parts
shall be regarded as contaminated when removed from the
hazardous area and appropriate action taken to prevent dust
dispersal.
• When using an extension lead, check the minimum cross-
sections of the cable:

10
WARNING: When carrying out service or repair
operations, all contaminated items which cannot be
satisfactorily cleaned are to be disposed of; such items
shall be disposed of in impervious bags in accordance
with any current regulation for the disposal of such
waste.
Cable length
Cross section
< 16 A < 25 A
up to 20 m 1.5 mm22.5 mm2
20 to 50 m 2.5 mm24.0 mm2
UNPACKING AND CHECKING CARTON
CONTENTS
1Push/Pull Handle 13 Filter Cleaning Button 25 Metal Extension Wand (x3)
2Carry Handle 14 Air Flow Indicator 26 Foam Filter
3Wing Knob 15 Hose Storage Rack 27 Cartridge Filter (pre-installed)
4Power Regulator 16 Accessory Storage 28 Disposable Bag (x5)
5 Latch 17 Squeegee Inserts 29 Washer (x4)
6 Rear Wheel 18 Brush Inserts (pre-installed) 30 Hub Cap (x2)
7 Front Caster 19 Floor Nozzle 31 Wheel Retaining Pin (x2)
8 Container 20 Suction Hose 32 Wheel Axle
9Cover Gasket 21 Crevice Tool 33 Screw (x2 )
10 Suction Port 22 Dust Bag (x5) 34 Instruction Manual
11 Power Take-off Socket 23 Round Dust Brush
12 On/Off Switch 24 Power Tool Hose Adaptor

11
ASSEMBLY
NOTE: A Phillips screwdriver is required.
1. Remove all the contents from inside of the vacuum cleaner container.
2. Attach the carry handle into the slots located on the top of the power head. Secure them with
supplied screws (Fig. 1).
3. Turn the container upside down and insert the front feet with casters into the slots and apply
pressure until they click into place (Fig. 2).
4. Insert the wheel axle into the rear wheel housing on the base. Insert a washer onto the axle
followed by the rear wheel and another washer. Insert the wheel retaining pin into the hole on
the end of the axle to lock into place. Push t the hub cap onto the wheel. Repeat the same
steps on the other end of the axle (Fig. 3).
5. To position the hose storage rack, insert one end into the channel on the side of the power
head, making sure it is secured in place. Apply inward pressure to the other side and insert it
into the opposite channel (Fig. 4).
6. Unfold the upper handle assembly into the upright position. The upper handle has two
adjustable height positions. Secure in place by tightening the wig knobs clockwise (Fig. 5).
7. Your vacuum cleaner comes ready for dry vacuum cleaning with the cartridge lter pre-installed.
If the cartridge lter is not installed, refer to page 13.
8. To maintain M-class certication this vacuum cleaner must be used with a disposable collection
means. By removing the dust bag and disposable bag when collecting debris the user runs the
risk of voiding vacuum cleaner certication.
1) To use a dust bag, fully t the dust bag ange onto the inlet stub (Fig. 6).
2) To use a disposable bag, place the disposable bag into the container, and fully t the
disposable bag ange onto the inlet stub. Fold the top edge of the disposable bag over the
rim of the container (Fig. 7).
3) To use a disposable bag and a dust bag together, place the disposable bag into the
container and fully t the disposable bag ange onto the inlet stub, and fold the top edge of
the disposable bag over the rim of the container, then fully t the dust bag ange onto the
inlet stub (Fig. 8).
9. For wet vacuum cleaning, replace the cartridge lter with the foam lter supplied. Do not use a
dust bag and/or a disposable bag when wet vacuuming. If the foam lter is not installed, refer to
page 14.
10.Secure the power head back on the container using the latches. Insert the locking end of the
hose into the suction port of the container and turn clockwise to lock into place (Fig. 9).
11. Choose the desired accessories and/or extension wands and push t onto the hose nozzle.
Floor Nozzle Attachments
The oor nozzle comes supplied with additional attachments to ensure correct suction across
different oor surfaces and applications.
1) To remove the oor nozzle attachments, turn the oor tool holder upside down.
2) Using a athead screwdriver or other suitable tool, locate the holding clips on each outer edge.
Insert a at edged object directly next to the holding clip, between the insert and the oor tool

12
1. Switching On/Off
Connect the mains plug to a suitable power outlet.
2. Power Tool Take-Off Operation (Fig. 13)
WARNING: Always check the maximum wattage compatibility of the power tool take off
socket against the desired power tool before connecting to prevent overloading.
1) Connect the power cable of your power tool to the power take-off socket.
2) If applicable, connect the vacuum suction hose to the dust extractor connector on your tool with
the supplied adaptor.
3) Switch the vacuum cleaner to position II, as described in Switching ON/OFF. The moment you
switch on the power tool, the vacuum cleaner will also switch on. Once the electrical appliance
has been switched off, the vacuum cleaner switches off following a time lapse (around 5
seconds) to allow the suction tube to be emptied.
3. Power Regulator
The airow can be continuously adjusted by turning the power regulator (Fig. 14).
MIN: Reduced suction for applications which generate a low level of dust.
MAX: Maximum suction performance for use in applications which generate a high level of dust.
4. Filter Cleaning Operation
IMPORANT: Only perform the lter cleaning operation when the cartridge lter is
installed.
After continuous dry vacuuming operation, air ow will decrease due to heavy accumulation of
material and debris on the cartridge lter. This vacuum is equipped with integrated lter cleaning to
increase dust collection efciency.
OPERATION
Position Status
I on
O off
II automatic synchronized start-up
holder. Pry the attachment up from underneath (Fig. 10 & 11).
3) Insert the new attachments into the holder applying downwards pressure (Fig. 11).
4) The attachments can be used in three combinations (Fig. 12):
Brush and Squeegee Combination: For use with mixture of wet or dry liquids.
Dual Brush Combination: For use with dry materials or carpeted oor surfaces.
Dual Squeegee Combination: For use on hard oor with wet liquids.
NOTE: The textured side of the rubber squeegee must be facing outwards.

13
When reduction of air ow (≤20m/s) has occurred during operation, the air ow indicator next to the
lter cleaning button located on top of the power head will admit a ashing red LED. If the suction
performance diminishes, you can improve the suction power with the help of the lter cleaning
system (Fig. 15).
1) Position the end of the suction hose nozzle into the channel located within the lter cleaner
button.
2) Move the on/off switch to the “I” position.
3) Turn the power regulator to the MAX position.
4) Press the lter cleaning button down and hold it down for 3-4 seconds (Fig. 16).
5) Repeat the process two more times.
5. Wet & Dry Vacuum Operation
WARNING: ENSURE YOU READ, UNDERSTAND AND APPLY SECTION
ENTITLED ‘SAFETY INFORMATION’.
WARNING: DO NOT VACUUM IN AREAS WITH FLAMMABLE GASES,
VAPOURS, OR EXPLOSIVE DUSTS IN THE AIR. FLAMMABLE GASES OR
VAPOURS INCLUDE BUT ARE NOT LIMITED TO; LIGHTER FLUID, SOLVENT
TYPE CLEANERS, OIL-BASE PAINTS, GASOLINE, ALCOHOL OR AEROSOL
SPRAYS. EXPLOSIVE DUSTS INCLUDE BUT ARE NOT LIMITED TO; COAL,
MAGNESIUM, GRAIN OR GUN POWDER.
1) Verify that the correct lter is installed and the container latches are secured.
2) Secure the locking end of the hose into the vacuum suction port.
3) Push the desired accessories onto the hose nozzle. The air ow regulation allows you to change
vacuum cleaner suction. For best cleaning results, fully close the air ow regulation (Fig. 17).
4) Plug the power cord into a power outlet.
5) Turn on the motor by assigning the switch to the “I” ON position.
6) Once you have completed vacuuming, switch to the “O” OFF position and unplug the power
cord from the power outlet.
For Dry Vacuuming:
WARNING: BEFORE INSTALLING, REMOVING OR CLEANING THE VACUUM
CLEANER FILTER, ENSURE THAT THE POWER CORD IS SWITCHED OFF
AND UNPLUGGED.
WARNING: ALWAYS USE A P2-RESPIRATOR WHEN VACUUMING
HAZARDOUS DUSTS.
1) To prepare your vacuum cleaner for dry vacuuming, install the cartridge lter over the lter
cage. Carefully push lter until it sits ush forming a tight seal. Tighten the lter retainer lock
clockwise to secure against the internal lter cage (Fig. 18).
2) Install the dust bag and/or the disposable bag onto the suction port inlet. Refer to page 11 for
installation instructions.
IMPORTANT: Before picking up dust with occupational exposure limit values:
Check that all the lters are present and properly tted.
For safety reasons, a visual warning indicator will activate if the air ow in the suction hose drops
to below 20 m/s.

14
Depending on how hazardous the dust is, the cleaner must be tted with appropriate lters and
collection means.
Dusts with OEL
values ≥0.1 mg/
m3(observe any
additional national
regulations)
Wood dusts &
concrete dusts.
Cartridge Filter + Disposable Bag
Cartridge Filter +
Dust Bag
Cartridge Filter + Dust Bag+ Disposable Bag
All dusts vacuuming
must t with
cartridge lter.
Cartridge Filter
IMPORTANT: Dispose of the dirt in accordance with legal regulations.
Remove the electrical plug from the socket before emptying after dry pick-up. After removing the
suction hose from the machine, close the cover gasket.
NOTE: The requirements for the ingress degree (dust category M) have only been certied for dry
vacuuming.
IMPORTANT: Check the lter regularly for optimal performance. An old or blocked lter will reduce
suction performance.
WARNING: When using the disposable bag, be careful not to vacuum heavy or sharp
objects. When removing the disposable bag, use a P2-respirator, and securley tie a knot in
the disposable bag. Do not make contact with any sharp objects and then carefully dispose
of in accordance with legal regulations.
For Wet Vacuuming:
Caution!
Never vacuum liquids without the water level limit system and foam lter in place.
NOTE: Empty the container before wet vacuuming.
1) To prepare your vacuum cleaner for wet vacuuming, release the retainer lock and remove the
dry use cartridge lter.
2) Carefully install the supplied foam lter over the internal lter cage ( ①), making sure the whole
cage is covered (Fig. 19).
WARNING: DO NOT USE DUST COLLECTION BAGS FOR WET VACUUMING.
IMPORTANT! The vacuum cleaner is equipped with a oat valve ( ②) which is operational during
wet suction (Fig. 20). The suction power decreases when the maximum lling level is reached.
When this happens, switch the vacuum cleaner off immediately, and empty the container.
+
+
+ +

15
MAINTENANCE
WARNING: REMOVE THE POWER CORD FROM THE POWER SUPPLY BEFORE
CARRYING OUT ANY MAINTENANCE.
WARNING: ALWAYS USE A P2-RESPIRATOR WHEN REMOVING THE CARTRIDGE
FILTER AFTER VACUUMING HAZARDOUS DUSTS.
1) Keep all safety devices, air vents and the motor housing free of dirt and dust. Use a soft, dry
brush to clean the equipment regularly.
2) Clear all dirt or debris from the collection tank after each use. Allow to dry before replacing the
power head.
3) Check the hose, attachments, and power cord to verify that they have not been damaged or
any debris is trapped and blocking airow.
1. Cleaning Cartridge Filter
IMPORTANT! After vacuuming hazardous dusts, it is recommended to dispose of the cartridge
lter within a sealed bag and dispose of in accordance with legal regulations.
IMPORTANT! When manually cleaning the cartridge lter, be careful not to damage the lter.
1) Remove the cartridge lter and clean by gently tapping or brushing dirt off. Ensure you always
use a P2-respirator and only do so in a well ventilated environment. For optimal performance it
is recommended to replace the old lter with a new lter regularly.
2) If necessary, use a mild soap and water solution to wash cartridge lter and rinse with clean
water. Allow the lters to air dry before re-installing.
2. Cleaning Foam Filter
Remove the foam lter and use a mild soap and water solution to wash and rinse with clean water
(Fig. 21). Allow lter to air dry before installing and using again.

16
TROUBLESHOOTING
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK-UNPLUG BEFORE
TROUBLESHOOTING.
Cleaning Performance
Vacmaster vacuum cleaners are tested for endurance. If your motor is operating, then the most
likely cause for a loss in suction is a blockage or an opening in the vacuum.
To maintain a high cleaning performance from your machine, it is important to replace or clean
cartridge lters as necessary. Replace full dust collection bags to prevent performance drops. A
performance drop with clean lters can only be caused by a blockage in the tools or the hose.
PROBLEM POSSIBLE CAUSE SOLUTION
The appliance does not
work.
No power. Check the power supply and fuse.
Functional fault in the power cord,
switch, or motor.
Have the damaged part checked by
qualied personnel or contact the
after sales helpline.
Dust is escaping from
the motor cover.
The cartridge lter is missing or
damaged. Put in a cartridge lter or replace it.
Misuse the foam lter when dry
vacuuming.
Replace the foam lter with the
cartridge lter.
Power tool take-off
socket does not work.
Power tool wattage is not
compatible with the power tool
take-off socket.
Check the wattage is compatible
with the power tool take-off socket.
Incorrect operating mode selected. Ensure the switch is moved into
position II.
Low suction power and
high operating noise /
vibrations.
Dust bag or disposable bag is full. Replace the dust bag or disposable
bag.
Suction nozzle, hose, or tank inlet
is blocked.
Check the suction nozzle, hose, and
tank inlet for obstructions.
Cartridge lter is blocked. Remove the cartridge lter and
clean.
Float valve has closed.
Empty the container of any liquid
waste and ensure the oat value
located underneath the lter is able
to move freely.
Power regulator switch is set to
minimum. Adjust variable power regulator.
The air ow indicator
is still red ashing
after completing lter
cleaning operation.
Suction nozzle, hose, or tank inlet
is blocked.
Check the suction nozzle, hose, and
tank inlet for obstructions.
The cartridge lter has been
contaminated heavily.
Remove and clean or replace with a
new lter.
The container is full. Empty the container.

17
RECYCLING AND DISPOSAL
TECHNICAL DATA
Model Number VDK1538SWC
Motor 220-240V~ 50Hz
Power Input 1500W
Max. Power Consumption Of the Power
Tool Take-Off Socket Outlet 800W for SAA Socket
Tank Volume 38L
Net Weight 14.0kg
Max. Vacuum Pressure 2 5 k P a / 2 5 0 h P a
Max. Flow Rate 71L/s / 255.6m³/h
Bearing Capacity of Disposable Bag 11.0kg
Bearing Capacity of Dust Bag 12.0kg
This marking indicates that this product should not be disposed with other household wastes
throughout the EU. The machine must be delivered in rigid packaging to avoid damage during
transportation. The packaging and the machine itself are manufactured from recyclable
materials and should be disposed of accordingly.
Noise/Vibration Information
Noise emission values determined according to EN 60335-2-69.
Typically, the A-weighted sound pressure level of the power tool is <78 dB(A).
Uncertainty K = 3 dB. The noise level when working can exceed 80 dB(A).
Total vibration values ah (triax vector sum) and uncertainty K determined according to
EN 60335-2-69: ah<2.5 m/s2, K =1.5 m/s2.

1
4
7
2
12
14
8 9
3
11
13
15 16
10
56
MAX MIN
MAX MIN