Vacon NX IP54 User manual

vacon nx
ac drives
ip54 control box
installation instructions
®

vacon • 1
24-hour support [phone] • Email: [email protected]
index
Document code: DPD01614A
Date: 1.7.2014
1.
CONTENTS OF THE DELIVERY............................................................................................ 2
2.
INSTALLATION ................................................................................................................... 3
2.1 Optic fibre cable, signal listing and connections....................................................................... 5
2.2 Cable bushing diameters ........................................................................................................... 6

2 • vacon CONTENTS OF THE DELIVERY
Tel. [phone] • Fax [phone]
1
1. CONTENTS OF THE DELIVERY
Figure 1. Contents of the IP 54 control box delivery
1IP54 control box
2IP54 cable entry grommet plates
3Grease for the grommet plates
4 Screws (4x10)
5Plastic pins
1
2
3
4
5

INSTALLATION vacon • 3
24-hour support [phone] • Email: [email protected]
2
2. INSTALLATION
These instructions guide you through the installation of the IP54 control box that you have purchased
for your FR12, FR14, FI12, FI14, CH64 or CH74 size frequency converter.
1. IP54 control box bottom plate with
starcoupler board
2. Connect the fibre optic cables. Push
carefully the cables into the cellfoam
bushings
3. Each fibre optic cable has a number
1...8 and 11…18 marked on the cable
shield at both cable ends. Connect each
cable to the connectors marked with
the same number on the starcoupler
board. The list of the optic signals can
be found in chapter 2.1
4. Connect the 24 V cable and lead it
through the bushing as shown in the
figure.
5. Close the cover by pushing it
carefully down so that the D-connector
connects thoroughly.
6. Attach the cover with four screws
(tightening torque 1,5 nm)
7. Apply a thin layer of grease to the
cellfoam washers
8. Push the cellfoam washer into the
guides in the enclosure.
9. Open the bushing for the cable. Pull
away the right size of piece according
to the cable size (in this figure 8 mm).

4 • vacon INSTALLATION
Tel. [phone] • Fax [phone]
2
10. Push the cable to the bushing.
Make sure that the cellfoam surrounds
the cable tightly.
11. Attach the cable to the washer with
a plastic binder
12. Apply some grease to the upper
cellfoam washer and push it to its
place.
13. Attach the seal around the RS485
connector.
14. Attach the cover plate with four
screws
15. Seal the holes with a piece of tape
and attach the RS485 cable
16. Push the plastic pins to the unused
cable entries .

INSTALLATION vacon • 5
24-hour support [phone] • Email: [email protected]
2
2.1 Optic fibre cable, signal listing and connections
Figure 2. Internal fibre cable connections
Star coupler board on control unit
H18 Trip signal frompower module 2
H17 VaconBus datafromASIC 2 to controlboard
H16 VaconBus datafromcontrolboardto ASIC 2
H15 ADC synchronization, power module 2
H14 PhaseW control, power module 2
H13 PhaseVcontrol, power module 2
H12 PhaseU control, power module 2
H11 Gatecontrolenable, power module 2
H23 Feedback phaseW
H22
Feedback phaseV
H21
Feedback phaseU
Terminals on ASIC board of power module 1
H1Gatecontrolenable
H2PhaseU control
H3PhaseVcontrol
H4PhaseW control
H5ADC synchronization
H6VaconBus datafromcontrolboardto ASIC
H7VaconBus datafromASIC to controlboard
Terminals on ASIC board of power module 2
H8Trip signal frompower module 1
H7VaconBus datafromASIC 1 to controlboard
H6VaconBus datafromcontrolboardto ASIC 1
H5ADC synchronization, power module 1
H4PhaseW control, power module 1
H3PhaseVcontrol, power module 1
H2PhaseU control, power module 1
H1Gatecontrolenable, power module 1
H10 Trip signal
Terminals on FB board of power module 2
H1Gatecontrolenable
H2PhaseU control
H3PhaseVcontrol
H4PhaseW control
H5ADC synchronization
H6VaconBus datafromcontrolboardto ASIC
H7VaconBus datafromASIC to controlboard
H10 Trip signal
H11 Feedback phaseU
H12 Feedback phaseV
H13 Feedback phaseW
Terminals on FB board of power module 1
H12
H13
H14
H15
H16
H17
H18
H11
H23
H22
H21
H2
H3
H4
H5
H6
H7
H8
H1
H7
H6
H5
H4
H3
H2
H1
H10
H7
H6
H5
H4
H3
H2
H1
H10
H13
H12
H11

6 • vacon INSTALLATION
Tel. [phone] • Fax [phone]
2
2.2 Cable bushing diameters
Figure 3. Cable bushing diameter

Document ID:
Rev. A
Manual authoring:
[email protected]
Vacon Plc.
Runsorintie 7
65380 Vaasa
Finland
Subject to change without prior notice
© 2014 Vacon Plc. Sales code: DOC-INSIP54BOX+DLUK
Find your nearest Vacon office
on the Internet at:
www.vacon.com