VADDIO RoboTRAK User manual

Integrator's Complete Guide to the
RoboTRAK Presenter Tracking System
Document 342-1229 Rev. E
November 2016

ii
Contents
What's in this Guide 1
Overview 1
Features 1
IR Camera 1
IRSource Lanyard 1
Unpacking the System 2
North America 3
Europe and UK 3
Australia and New Zealand 4
A Quick Look at the RoboTRAK System 5
Front of the IR Camera 5
Status Indications 5
Connectors 6
Lanyard 6
Before You Start 7
Network Requirements 7
Additional Equipment 7
Lighting and IR 7
Camera Location 9
Camera Placement – Small Room 9
Camera Placement – Medium Room 10
Camera Placement – Large Room 11
Installation 12
Don’t Void Your Warranty! 12
Cabling Notes 12
The IR Camera's Default Hostname 13
Before You Install the Camera 13
Placing the PoE Splitter 14
Installing the Camera Mount 15
Wall Installation 15
Ceiling Installation 15
Basic Connection Diagram 16
Connections for Configuring the System 16
Installing the Cameras 17
Preparing the Tracking Lanyard for Use 17
Powering Up the Cameras 17
Configuring the Tracking System 18
Establishing Communication Between the Cameras 18
Accessing the IR Camera's Web Interface 18
Loading the Room Configuration File 20

Accessing the Video Camera's Web Interface 21
Assigning Hostnames or IP Addresses to the Cameras 22
Configuring the Video Camera 23
Pairing the Cameras 24
Setting the Video Camera's Standby Behavior 24
Setting up the IR and Video Camera Lanyard Shots 25
Viewing the Stream from the IR Camera 25
Storing the IR Camera's Lanyard Shot 26
Storing the Video Camera's Lanyard Shot 28
Testing and Fine-Tuning 30
Tuning Cheat Sheet 31
Setting the IR Camera's Home Position 32
Setting the Lanyard Searching Behaviors 33
Setting the Presenter Area and Search Area 34
Adjusting AGC Gain 36
Setting the Tracking Speed: Speed Scaler 37
Setting IRCamera Responsiveness: Tracking Sensitivity 38
Adjusting the Video Camera Window Width 39
Dealing with Stray IR 40
Configuring the Video Camera 42
Exporting the Configuration 43
Web Interface Cheat Sheet 44
System Administration 45
Security Settings 45
Setting the Room Label Information 46
Specifying Time Zone and NTP Server 46
Pan-Tilt Reset, Reboot, and Factory Reset 47
Reset the Pan and Tilt Motors 47
Reboot the Camera 47
Restore Factory Settings 47
Downloading and Installing Firmware Updates 48
Getting Help 49
Presenting with the RoboTRAK System 49
How It Works 50
Tips for Great Presentations 50
Starting Your Presentation 50
Switching Between Tracking and Camera Presets 50
How the Cameras Behave 51
Tips for Handling and Storing the Lanyard 51
Telnet Serial Command API 52
About Controlling the Video Camera via Telnet 52
iii
Integrator's Complete Guide to the RoboTRAK Presenter Tracking System

Commands to Avoid 52
camera master tracking 53
camera master recalibrate 53
camera master standby 53
camera master standby config peripheral 54
camera master ccu 54
camera slave1 preset recall 55
network ping 55
network settings get 55
streaming settings 56
system reboot 56
system factory-reset 57
sleep 57
help 58
history 58
version 59
exit 59
Troubleshooting and Care 60
Status Indications 60
Fault Isolation 60
Operation, Storage, and Care 61
Specifications 62
Compliance Statements and Declarations of Conformity 63
FCC Part 15 Compliance 63
ICES-003 Compliance 63
European Compliance 64
Warranty Information 65
Index 66
iv
Integrator's Complete Guide to the RoboTRAK Presenter Tracking System

1
What's in this Guide
This guide provides information on the following topics:
nUnpacking and installing RoboTRAK cameras
nThe camera's physical features and switch settings
nControlling the camera using the IR remote or web interface
nControlling the camera using Telnet or RS-232 commands
nSpecifications
nTroubleshooting and maintenance
nWarranty and compliance/conformity information
For your convenience, this information is also available in smaller, limited-purpose manuals:
nInstallation Guide for the RoboTRAK Presenter Tracking System (unpacking, physical features,
switch settings, installation, initial power-up)
nConfiguration and Administration Guide for the RoboTRAK Presenter Tracking System
(physical features, controlling the camera, troubleshooting, and specifications)
Download manuals, dimensional drawings, and other information from www.vaddio.com/support.
Overview
This guide covers the RoboTRAK presenter tracking system with IR
camera:
nRoboTRAK, North America – 999-7270-000
nRoboTRAK, Europe and UK – 999-7270-001
nRoboTRAK, Australia and New Zealand – 999-7270-009
This system requires a video camera, which is sold and documented
separately. The RoboTRAK system works with RoboSHOT™ series
cameras. Refer to the video camera's documentation for information on how
to connect and configure it.
Features
nIR-based presenter tracking for medium to large rooms
nDesigned for educators, in consultation with educators, using Vaddio's proven, industry-leading
technology
nReliable tracking: Move around, turn your head, invite others to the front of the room... the camera stays
on you
nSwitch between tracking and preset positions
nCamera sold separately – use with the RoboSHOT™ camera of your choice
IR Camera
nSimple configuration and administration using the Vaddio web interface
nAdjust the system's tracking behavior to match the presenter's style
nOperational range of 12 to 50 ft (3.7 to 15.2 m), any height from 6 to 15 ft. (1.8 to 4.6 m)
IRSource Lanyard
nNo belt pack – comfortable, highly wearable design that does not interfere with clothing
nUp to 40 hours of battery power; 25 hours typical
nRecessed switch for full power-down – Conserve battery life during storage; no risk of accidental
actuation

Unpacking the System
Make sure you received all the items you expected.
Vaddio recommends purchasing a second lanyard as a spare or for smooth transitions between multiple
presenters.
Note
In addition to the items listed here, you will need a video camera. Any RoboSHOT series camera can be
used.
If remote viewing is desired, you must use a video camera that is capable of streaming. These include
RoboSHOT 10 USB, RoboSHOT HD-SDI, and RoboSHOT 20 UHD cameras.
Caution
Always support the camera's base when picking it up. Lifting the camera by its head or mounting
arm will damage it.
Note
Copy the default hostname from the label on the bottom of the camera, and keep this information in a place
where it will be available to anyone who needs to work with the camera's web interface. This information is
required to access the camera for initial configuration, or after a factory reset.
2
Integrator's Complete Guide to the RoboTRAK Presenter Tracking System

North America
Part number 999-7270-000, RoboTRAK
nVaddio RoboTRAK IR camera
nPoE+ power injector
nAC cord set for North America
nPoE splitter
nPower cable, 1 ft (30 cm)
nCat-5e cable, 1 ft (30 cm)
nCat-5e cable, 10 ft (3 m)
nWall mount with mounting hardware
nIR lanyard
nUSB charger
nUSB charger cable
nFerrite bead
nQuick Start Guide
Part number 999-7271-000, additional lanyard kit (optional, purchased separately):
nLanyard
nUSB charger
nUSB charger cable
nFerrite bead
Europe and UK
Part number 999-7270-001, RoboTRAK
nVaddio RoboTRAK IR camera
nPoE+ power injector
nAC cord sets for Europe and UK
nPoE splitter
nPower cable, 1 ft (30 cm)
nCat-5e cable, 1 ft (30 cm)
nCat-5e cable, 10 ft (3 m)
nWall mount with mounting hardware
nIR lanyard
nUSB charger
nUSB charger cable
nFerrite bead
nQuick Start Guide
Part number 999-7271-001, additional lanyard kit (optional, purchased separately):
nLanyard
nUSB charger
nUSB charger cable
nFerrite bead
3
Integrator's Complete Guide to the RoboTRAK Presenter Tracking System

Australia and New Zealand
Part number 999-7270-009, RoboTRAK in silver and black
nVaddioRoboTRAK IR camera
nPoE+ power injector
nAC cord set for Australia and New Zealand
nPoE splitter
nPower cable, 1 ft (30 cm)
nCat-5e cable, 1 ft (30 cm)
nCat-5e cable, 10 ft (3 m)
nWall mount with mounting hardware
nIR lanyard
nUSB charger
nUSB charger cable
nFerrite bead
nQuick Start Guide
Part number 999-7271-009, additional lanyard kit (optional, purchased separately):
nLanyard
nUSB charger
nUSB charger cable
nFerrite bead
4
Integrator's Complete Guide to the RoboTRAK Presenter Tracking System

A Quick Look at the RoboTRAK System
This section covers the physical features of the RoboTRAK system:
nIR camera
nTracking Lanyard
The RoboTRAK system requires a video camera as well. You can use any Vaddio RoboSHOT camera as
the video component of the system.
Note
If remote viewing is desired, you must use a video camera that is capable of streaming. These include
RoboSHOT 10 USB, RoboSHOT HD-SDI, and RoboSHOT 20 UHD cameras.
Refer to the documentation for your RoboSHOT camera for detailed information on connections and
camera control.
Front of the IR Camera
nCamera assembly – based on the same reliable hardware as our latest generation of video cameras.
nReflective lens – reduces interference from spurious IR sources. The reflective lens also provides a
simple visual cue that it's not a standard video camera.
nIndicator light – shows the IRcamera's current status.
Status Indications
In normal use, the RoboTRAK IR camera's status light will provide more useful information than the video
camera's indicator light.
nGreen – Tracking or waiting at the home position
nBlue – Not in tracking mode (may be at a video camera preset position)
nBlinking green – Searching for the lanyard
nBlinking blue – Not paired or not in contact with the video camera
nPurple – In standby mode or booting
nBlinking yellow – Executing a pan-tilt reset
nYellow – Updating firmware
5
Integrator's Complete Guide to the RoboTRAK Presenter Tracking System

Connectors
n12 VDC, 3.0 Amp power connector – Connect only the PoE splitter shipped with the camera.
nNetwork/PoE+ – 10/100 Ethernet/PoE+ port allows the RoboTRAK™ IR camera to control the video
camera, and provides access to the web interface.
nDIP switches – Factory use only.
Lanyard
Vaddio recommends purchasing a second lanyard as a spare or for smooth transitions between multiple
presenters.
Medallion – Houses charging and control circuitry, switches to standby (low-power)mode when the IR
camera switches to standby.
nButton – On/off switch for IR sources
nIlluminated ring – Visual status indicator directs light toward the wearer,
not the audience
nBattery – Rechargeable Li-ion battery; up to 25 hour battery life, roughly 4
hour charging time
nUSB micro-B charging port – Connect the supplied battery charger
nRecessed power switch – Allows you to turn off the lanyard completely to
extend battery life
Ribbon – Holds the medallion and contains the IRsources.
nStrand of IR LEDs – Provide a characteristic image pattern that the
camera identifies and tracks
nSafety clasp – Automatically releases under tension
Caution
Do not pinch, crease, or stretch the lanyard ribbon. Do not pull the lanyard ribbon to release the clasp. Any
of these will damage the circuitry in the ribbon.
6
Integrator's Complete Guide to the RoboTRAK Presenter Tracking System