Valor fiers 757 Instructions for use

5119815/03
© Baxi Heating U.K. Limited 2007.
Model757
REMOTE CONTROL
INSET LIVE FUEL EFFECT GAS FIRE
Fitted with one of the following fascia.
Splendour Landscape Stone
Splendour Portrait Stone
Splendour Portrait Black.
(GC No. 32-264-22)
We trust that this guide gives
sufficient details to enable this
appliance to be installed and
maintained satisfactorily. However, if
further information is required, our
Valor Fires Technical Helpline will
be pleased to help.
Telephone [phone] (National
call rates apply in the United
Kingdom).
In the Republic of Ireland
Telephone [phone].
INSTALLER: Please leave this guide with the
owner
INSTALLER AND OWNER GUIDE

© Baxi Heating U.K. Limited 2007.
All rights reserved. No part of this publication may be reproduced in any material form
(including photocopying), stored in any medium by electronic means (including in any
retrieval system or database) or transmitted, in any form or by any means, whether
electronic, mechanical, recording or otherwise, without the prior written permission of
the copyright owner.
Applications for the copyright owner's permission to reproduce any part of this
publication should be made, giving details of the proposed use, to the following
address: The Company Secretary, Baxi Heating UK Limited, The Wyvern Business
Park, Stanier Way, Derby, DE21 6BF.
Warning: Any person who does any unauthorised act in relation to a copyright work
may be liable to criminal prosecution and civil claims for damages.
Valor Fires, Erdington, Birmingham B24 9QP
www.firesandstoves.co.uk
Because our policy is one of constant development and improvement, details may vary slightly from
those given in this publication
Page 2
INSTALLER GUIDE
© Baxi Heating U.K. Limited 2007.
THIS APPLIANCE IS FOR USE WITH NATURAL GAS (G20).
WHEN CONVERTED USING CONVERSION KIT NO. 0575621 THIS
APPLIANCE IS FOR USE WITH PROPANE GAS (G31).
THIS APPLIANCE IS SUITABLE ONLY FOR INSTALLATION IN THE UNITED
KINGDOM (GB) AND THE REPUBLIC OF IRELAND (IE).

Safety First.
Valor Fires fires are CE Approved and designed to meet the appropriate British
Standards and Safety Marks.
Quality and Excellence.
All Valor Fires fires are manufactured to the highest standards of quality and
excellence and are manufactured under a BS EN ISO 9001 quality system accepted
by the British Standards Institute.
The Highest Standards
Valor Fires is a member of SBGI and HHIC (Heating and Hot water Industry Council)
which works to ensure high standards of safety, quality and performance.
Careful Installation
Valor Fires is a CORGI registered company. All our gas fires must be
installed by a competent CORGI Registered Installer in accordance
with our Installer Guide and should not be fitted directly on to a
carpet or floor of combustible material.
Page 3
INSTALLER GUIDE
© Baxi Heating U.K. Limited 2007.

Page 4
INSTALLER GUIDE
© Baxi Heating U.K. Limited 2007.
INSTALLERGUIDE
FOR OWNER GUIDE SEE PAGES 37 TO 51

CONTENTS
Section Heading
Page
INSTALLER GUIDE
4 - 36
OWNER GUIDE
37 - 51
1. SAFETY 6
2. ACCESSORY LIST 6
3. APPLIANCE DATA 7
4. GENERAL INSTALLATION REQUIREMENTS 8
5. PACK CONTENTS 15
6. FIREPLACE CHECK 17
7. IGNITION CHECK 18
7.1 Fitting batteries to the remote control handset. 18
7.2 Fitting batteries to the receiver box. 18
7.3 Checking the ignition operation. 19
7.4 Adjusting the remote control handset / receiver code. 19
8. GAS SUPPLY CONNECTION 20
9. PREPARING APPLIANCE FOR INSTALLATION 20
10. HOTBOX INSTALLATION 23
10.1 Cable retention and floor fixing. 23
10.2 Sealing Hotbox to fireplace opening. 25
10.3 Fitting the wall brackets. 25
11. BURNER & SUPPLY PIPE INSTALLATION 27
12. FASCIA INSTALLATION 29
13. FULL OPERATING CHECKS 29
14. FINAL REVIEW 31
15. SERVICING & PARTS REPLACEMENT 32
15.1 To remove the fascia. 33
15.2 To remove the burner unit. 33
15.3 To remove the spillage plate. 34
15.4 To remove the inner panel. 34
15.5 To remove the pilot unit. 34
15.6 To remove the gas valve. 35
15.7 To remove the receiver box. 35
15.8 To replace the top surface of the burner. 36
15.9 To replace the burner (bowl). 36
15.10 To remove the burner injector. 36
15.11 To remove the appliance from the fireplace. 36
Page 5
INSTALLER GUIDE
© Baxi Heating U.K. Limited 2007.

1. SAFETY
Installer
Before continuing any further with the installation of this appliance please read the
following guide to manual handling:
! The approximate lifting weight (kg) of this appliance is as below:
Model Convector Heat Fascia Total
box engine
Splendour Landscape Stone 5.56 9.31 27 41.87
Splendour Portrait Stone 5.56 9.31 20 34.87
Splendour Portrait Black 5.56 9.31 20 34.87
!
Without the fascia fitted, one person should be sufficient to lift the fire. If for any
reason this weight is considered too heavy then obtain assistance.
The fascia
is heavy and we recommend two people should be sufficient to lift it.
!
When lifting always keep your back straight. Bend your legs and not your back.
! Avoid twisting at the waist. It is better to reposition your feet.
!
Avoid upper body/top heavy bending. Do not lean forward or sideways whilst
handling the fire.
!
Always grip with the palm of the hand. Do not use the tips of fingers for support.
! Always keep the fire as close to the body as possible. This will minimise the
cantilever action.
! Use gloves to provide additional grip.
! Always use assistance if required.
2. ACCESSORY LIST
The following accessories are available: -
Description
Part Number
Pre cast and clay flue block spacer kit 05654K1
LPG conversion kit 0575621
Hearth (Stone colour) (W) 825mm, (D) 300mm, (H) 50mm 5121114
Hearth (Black colour) (W) 825mm, (D) 300mm, (H) 50mm 5121322
Page 6
INSTALLER GUIDE
© Baxi Heating U.K. Limited 2007.

3. APPLIANCE DATA
* When converted using conversion kit number 0575621.
The appliance data label is located on a plate at the base of the fire. This can be
seen by lowering the bottom front cover of the fascia.
The efficiency of this appliance has been measured as specified in BS 7977 - 1 and
the result is as below:
Model
Efficiency % (Gross)
757 47
757 when converted to LPG. 47
The gross calorific value of the fuel has been used for this efficiency calculation. The
test data from which it has been calculated has been certified by Advantica
Certification services (0087). The efficiency value may be used in the UK
Government's Standard Assessment Procedure (SAP) for energy rating of dwellings.
The conversion of net efficiency to gross was achieved by multiplying the net
efficiency by the following conversion factor from Table E3 of SAP 2005, rounding
down to the nearest whole number.
Page 7
INSTALLER GUIDE
© Baxi Heating U.K. Limited 2007.
Gas Natural (G20) Propane (G31)*
Inlet Pressure 20mbar 37mbar
Input Max. (Gross) 5.3kW (18,084 Btu/h) 5.3kW (18,084 Btu/h)
Input - Min. (Gross) 3.2kW (10,918 Btu/h) 4.3kW (14,672 Btu/h)
Inlet Test Pressure (Cold) 20.0 ± 1.0mbar (8.0 ± 0.4in
w.g.)
37.0 ± 1.0mbar (14.85 ±
0.4in w.g.)
Gas Connection 8mm pipe 8mm pipe
Burner Injector Stereomatic size 170 Stereomatic Size 115
Pilot & Atmosphere
Sensing Device OPNG 9030 OPLPG 9222
Ignition Battery powered electronic
remote control.
Battery powered electronic
remote control.
Aeration Non-adjustable Non-adjustable
Gas Conversion factor from net to gross efficiency
Natural Gas 0.901
LPG 0.921

This product uses a burner gasket and burner surface containing Refractory
Ceramic Fibres (RCF), which are man-made vitreous silicate fibres. Excessive
exposure to these materials may cause irritation to eyes, skin and respiratory
tract. Consequently, it is important not to touch or disturb the burner surface to
ensure that the release of dust is kept to a minimum. To ensure that the release
of fibres from these RCF articles is kept to a minimum, during installation and
servicing we recommend that you use a HEPA filtered vacuum to remove any
dust and soot accumulated in and around the fire before and after working on
the fire. Do NOT vacuum the burner surface. When replacing the the burner
surface we recommend that the replaced items are not broken up, but are
sealed within a heavy duty polythene bag, clearly labelled as RCF waste.
RCF
waste is classed as a stable, non-reactive hazardous waste and may be
disposed at a landfill licenced to accept such waste.
Protective clothing is not
required when handling these articles, but we recommend the use of suitable
gloves to prevent irritation. We also recommend you follow the normal hygiene
rules of not smoking, eating or drinking in the work area and always wash your
hands before eating or drinking.
This appliance does not contain any component manufactured from asbestos
or asbestos related products.
4. GENERAL INSTALLATION REQUIREMENTS
4.1 The installation must be in accordance with these instructions.
For the user’s protection, in the United Kingdom it is the law that all gas appliances
are installed by competent persons in accordance with the current edition of the Gas
Safety (Installation and Use) Regulations. Failure to install the appliance correctly
could lead to prosecution. CORGI requires its members to work to recognised
standards.
In the United Kingdom the installation must also be in accordance with:
All the relevant parts of local regulations.
All relevant codes of practice.
The relevant parts of the current editions of the following British Standards:-
BS 715
BS 1251
BS EN 1858 which replaces BS 1289 Part 1
BS EN 1806 which replaces BS 1289 Part 2
BS EN 1856 Part 1 which replaces BS 4543 Part 2
BS 5440 Part 1
BS 5440 Part 2
BS 5871 Part 2
BS 6461 Part 1
BS 6891
BS 8303
Page 8
INSTALLER GUIDE
© Baxi Heating U.K. Limited 2007.

In England and Wales, the current edition of the Building Regulations issued by the
Department of the Environment and the Welsh Office.
In Scotland, the current edition of the Building Standards (Scotland) Regulations
issued by the Scottish Executive.
In Northern Ireland, the current edition of the Building regulations (Northern Ireland)
issued by the Department of the Environment for Northern Ireland.
In the republic of Ireland the installation must also conform to the relevant parts of:
a) The current edition of IS 813 “Domestic gas installations”.
b) All relevant national and local rules in force.
Where no specific instructions are given, reference should be made to the relevant
British Standard Code of Practice.
4.2 In the United Kingdom, as supplied, the appliance can be installed in the
following situations:
4.2.1 To a fireplace
complete with
surround and
hearth as shown in
figure 1 and
complying with
BS1251 after
removal of the
fireback and
sufficient material
behind the fireback
for a debris
catchment space.
The required
fireplace, hearth,
debris catchment
area and clearance
dimensions are
shown in figure 1.
4.2.1.1 ‘Hole-in-the-wall’ installations.
! It is recommended that a hearth should be installed as in figure 1.
If a hearth is not fitted, the fire must be installed so that the distance from the base of
the fireplace opening in the wall to the finished floor level is at least 25mm. Where
there is no floor covering or carpet and the floor is of a type that is likely to be
covered in such a way then the distance from the base of the fireplace opening in the
wall to the finished floor level should be increased to at least 100mm.
!
To protect from the risk of burns and ignition of clothing a tactile separator shall be
used. The hearth detailed in section 4.9 meets the requirements for a tactile
Page 9
INSTALLER GUIDE
© Baxi Heating U.K. Limited 2007.
Figure 1. Hearth and fireplace opening dimensions

separator. If this is not used then a 672mm long fender, kerb, horizontal bar, or other
barrier, being fixed not less than 50mm above floor level and positioned 300mm in
front of the fixing plane of the fire will meet the requirement.
4.2.2
To a fireplace incorporating a metal flue box complying with the constructional
requirements of BS 715 and BS EN 1856 Part 1. The dimensions of the flue box must
conform to those shown in figure 2.
4.2.3
A precast concrete or clay flue block system conforming to BS EN 1806, BS EN
1858 or BS 1289 with dimensions
as in figure 3 or using a 05654K1
spacer kit. (Installation Instructions
part number 3003095). The current
versions of BS1289 and BS EN
1806 (NA 2.4) recommend that there
should be an air space or insulation
between the flue blocks and the
plaster because heat transfer may
cause cracking on directly plastered
flues. However, generally this
appliance is suitable for installations
under all circumstances unless there
is a history of cracking problems.
Remember that faults such as
cracking may be caused by poorly
built and restrictive flues, e.g. mortar
extrusions, too many bends, flue
heights below three metres,
restrictive terminations etc (See figure 3).
4.2.4
If the fireplace opening is greater than the acceptable dimensions given in this
guide, do not use the back of a fire surround or marble to reduce the opening. This
may cause cracking of the surround back or marble.
4.3 Suitable flues and minimum flue sizes are as follows: -
It should be noted that, as with many appliances, sharp bends or horizontal runs in
metal flues at the top of the system can be a cause of problems in these types of
installation.
! 225mm x 225mm conventional brick flue.
! 175mm diameter lined brick or stone flue.
!
200mm diameter factory made insulated flue manufactured to the current edition
of BS EN 1856 or BS 4543.
! 175mm diameter flue pipe. See BS6461 Part 1 for suitable materials.
!
Single wall, twin wall or flexible flue liner with a minimum diameter of 125mm. The
materials to be used are stainless steel or aluminium as specified in
BS EN 1856 Part 1. The liner must be sealed to the surrounding area above the
fireplace opening and to the top of the chimney. An approved terminal must be fitted.
Page 10
INSTALLER GUIDE
© Baxi Heating U.K. Limited 2007.
Figure 2. Metal flue box

! A properly constructed precast
concrete or clay flue system
conforming to BS EN 1806, BS EN
1858 or BS1289. This system is only
suitable if the conditions stated in
section 4.2.3 are met.
4.4 The flue must conform to BS
5440: Part 1 in design and
installation.
The flue, measured from the bottom
of the fireplace opening to the bottom
of the terminal, shall be not less than
3m in actual vertical height. When
calculated in accordance with BS
5440: Part 1 Annex A, the minimum
equivalent height of the flue shall be
2.0m of 125mm-dia. flue pipe.
4.5 The flue must not be used for
any other appliance or application.
4.6 Any chimney damper or
restrictor should be removed. If
removal is not possible, they must be
secured in the open position.
4.7 If the appliance is intended to
be installed to a chimney that was
previously used for solid fuel, the flue must be swept clean prior to installation. All
flues should be inspected for soundness and freedom from blockages.
4.8
If the fireplace opening is an underfloor draught type, it must be sealed to stop
any draughts.
4.9 The appliance must be mounted behind a non-combustible hearth (N.B.
conglomerate marble hearths are considered as non-combustible) unless the
conditions of section 4.2.1.1. The appliance can be fitted to a purpose made
proprietary class “O”-100°C surround. The hearth material must be at least 12mm
thick. The periphery of the hearth (or fender) should be at least 50mm above floor
level to discourage the placing of carpets or rugs over it.
The surface of the hearth must be sufficiently flat to enable the bottom of the fascia
and the bottom front cover to be aligned horizontally. Any excessive unevenness
(uneven tiles, Cotswold stone, etc.) should be rectified.
The appliance must not stand on combustible materials or carpets.
Page 11
INSTALLER GUIDE
© Baxi Heating U.K. Limited 2007.
Figure 3. Precast or clay flue block system
dimensions

4.10
The front face of the fireplace should be reasonably flat over the area covered
by the hotbox top and side flange seals to ensure good sealing. These faces should
be made good if necessary.
The fireplace floor should be reasonably flat to ensure that a good seal with the
hotbox can be made.
4.11
Note that soft wall coverings (e.g. embossed vinyl, etc.) are easily affected by
heat. They may scorch or become discoloured when close to a heating appliance.
Please bear this in mind when installing.
4.12
This appliance must not be installed in any room that contains a bath or shower
or where steam is regularly present.
4.13
An extractor fan may only be used in the same room as this appliance, or in any
area from which ventilation for the appliance is taken, if it does not affect the safe
performance of the appliance. Note the spillage test requirements detailed further on
in this manual. If the fan is likely to affect the appliance, the appliance must not be
installed unless the fan is permanently disconnected.
4.14 Normal adventitious ventilation is usually sufficient to satisfy the ventilation
requirements of this appliance. In GB reference should be made to BS 5871 Part 2
and in IE reference should be made to the current edition of IS 813 “Domestic Gas
Installations” which makes clear the conditions that must be met to demonstrate that
sufficient ventilation is available.
4.15 If the appliance is to be fitted against a wall with combustible cladding, the
cladding must be removed from the area
covered by the fascia. The cladding
must also not touch the fascia (See
figure 4). We suggest that the actual
fascia is used as a template to mark the
area for combustible cladding removal
and that this area is increased by at
least 2mm all round. If the cladding
projects forward from the fixing plane of
the fire the clearance at the top of the
appliance must be increased to a
minimum 40mm.This will allow for fascia
removal.
Page 12
INSTALLER GUIDE
© Baxi Heating U.K. Limited 2007.
Figure 4. Removal of combustible
cladding.(Fascia may differ from that
shown)

4.16
The minimum height from the base of the fireplace opening to the underside of
any shelf made from wood or other combustible materials is shown below: -
•For a shelf up to 150mm deep
Minimum height = 700mm.
•For a shelf deeper than 150mm
Minimum height = 700mm + 12.5mm for every 25mm depth over 150mm.
(See graph 1).
4.17 On metal chimneys,
proprietary terminals must comply with BS EN 1856 Part 1.
Any terminal or termination must be positioned in accordance with BS 5440 Part 1 to
ensure that the products of combustion can be safely dispersed into the outside
atmosphere. Where the appliance is connected to an unlined brick chimney it is
generally unnecessary for the chimney pot to be replaced or for a terminal to be fitted
unless the flue has a diameter smaller than 170mm.
4.18 The appliance is fitted with an A.S.D (Atmosphere sensing device). If the
appliance closes down after a period of operation for no apparent reason, the
consumer should be informed to stop using the appliance until the installation and
appliance have been thoroughly checked. The A.S.D will shut the appliance down if
an unacceptable amount of harmful products of combustion accumulate. Under no
circumstances should the A.S.D be altered or bypassed in any way. Only a genuine
manufacturer’s replacement part should be fitted. The individual A.S.D components
are not replaceable.
4.19 The minimum allowable distance from the outside of the appliance fascia to a
corner wall having combustible material or any other combustible surface which
projects beyond the front of the appliance is shown in figure 5.
Page 13
INSTALLER GUIDE
© Baxi Heating U.K. Limited 2007.
Graph 1. Combustible shelf clearances

Page 14
INSTALLER GUIDE
© Baxi Heating U.K. Limited 2007.
Figure 5. Appliance dimensions and clearances

5. PACK CONTENTS
Pack 1
1Burner & Hotbox Unit
1Spacing frame (Three separate pieces)
6Edge clips for securing the spacing frame
1Inlet ‘T’ Connector which includes a nut and olive for 8mm inlet pipe
1Flue restrictor plate
2Screws (For flue restrictor)
2Fireback spacing brackets
2Screws (For Fireback spacing brackets)
2Small “U” seals for hotbox side flanges
1Strip of floor sealing tape
4Eyebolts
1Long length of foam seal
1Short length of foam seal
6Fibre / Wooden plugs
4Woodscrews
2Fire retaining cables
2Cable clamps
1Rubber grommet
1Literature pack
1Smoke match tube
1Elliptical burner bezel
4Screws for fascia heat baffle
1Remote control handset.
1PP3 battery (For handset)
4AA Batteries (For receiver)
Pack 2 (Fascia)
1Fascia
1Fascia heat baffle
4Hanging brackets
8Screws
8Wall plugs
2Pairs of gloves
1
Bottle of touch-up paint (On black fascias two bottles may be supplied - one as
a base coat and the other as texture).
1Eraser
Carefully remove all the contents. Check that all the listed parts are present and in
good condition. The pack may contain additional components to that stated above.
These can be discarded following installation.
Page 15
INSTALLER GUIDE
© Baxi Heating U.K. Limited 2007.

Page 16
INSTALLER GUIDE
© Baxi Heating U.K. Limited 2007.
Figure 6. Pack contents

6. FIREPLACE CHECK
6.1 Fireplace check.
6.1.1 Fireplace size
The fireplace must comply with
the requirements described in
section 4.2. This will probably
entail removing the fireback and
infill material behind the
fireback. The debris catchment
area shown in figure 7 must be
kept clear of obstructions.
6.1.2 Fireplace general
condition
The fireplace floor should be
reasonably flat to ensure that
the hotbox can be installed
without it rocking and so that a
good seal can be made at the
bottom front of the box. The front face of the fireplace should be reasonably flat over
the area covered by the spacing frame top and side flange seals to ensure good
sealing. These faces should be made good if necessary. If the appliance is to be fitted
against a wall with combustible cladding, the cladding must be removed from the area
covered by the fascia. The cladding must also not touch the fascia (See figure 4). We
suggest that the actual fascia is used as a template to mark the area for combustible
cladding removal and that this area is increased by at least 2mm all round. If the
cladding projects forward from the fixing plane of the fire the clearance at the top of
the appliance must be increased to a minimum 40mm.This will allow for fascia
removal.
6.1.3 Soundness for appliance attachment
A primary method of retaining the appliance is provided. This involves using
concealed tension cables fixed to the rear of the fireplace opening together with
secondary fixing to the fireplace floor. This method is detailed in section 10 of this
manual. This method is particularly useful for instances where drilling holes in the
front surface of the fireplace surround is unacceptable to the customer or otherwise
impractical. N.B. It is unwise to attempt to drill into marble without the proper tools
and equipment.
Make sure that the areas at the back and towards the centre of the fireplace floor are
sound enough to take the eyebolts and screws. If these areas have deteriorated due
to prolonged use, they should be made sound with suitable cement.
Page 17
INSTALLER GUIDE
© Baxi Heating U.K. Limited 2007.
Figure 7. Fireplace area

6.1.4 Installations using a metal flue box
The whole of the top surface of the metal flue box must be covered with a 100mm
layer of mineral wool or equivalent insulation (See figure 2).
6.2 Fireplace flue pull.
Close all doors and windows in the room in which the appliance is to be installed.
After confirming with a match that smoke is drawn into the flue, light a 13 gram
smoke pellet and check that there is a definite flow through the flue. Verify outside
that the smoke exits from one terminal only and that the termination is suitable.
Observe where possible, upstairs rooms and loft spaces for signs of escaping smoke
indicating a defective flue. If there is not a definite flow warm the flue for a few
minutes and repeat the smoke pellet test. If there is still no definite flow the flue may
need remedial work – Do not fit the appliance until there is a definite flow
through the flue.
7. IGNITION CHECK
Before attempting to install, it is worth checking that the ignition system performs
satisfactorily. See section 7.4 for adjusting the handset and receiver code.
7.1 Fitting batteries to the remote control handset.
The remote control handset is battery powered. There is a 9 Volt ‘PP3’ size battery
supplied. Remove the rear battery compartment cover from the remote control
handset. To do this, push the tab towards the
bottom of the handset and lift (See figure 8).
Fit the battery in to the handset. Replace the
cover.
7.2 Fitting batteries to the receiver box.
The gas valve and receiver are battery
powered. There are four 1.5 Volt ‘AA’ size
batteries supplied. Locate the batteries in the
receiver box. To do this slide the receiver box
forward and clear of its support. Slide the
battery compartment cover clear (See figure
8) and fit the batteries. It is important that the
+ve and -ve symbols on the battery match
those of the illustration inside the battery
holder. Replace the cover and receiver box. It
is important that the wires from the
receiver box do not touch the underside of
the burner tray.
Page 18
INSTALLER GUIDE
© Baxi Heating U.K. Limited 2007.
Figure 8. Battery compartment covers
Handset
Receiver box

7.3 Checking the ignition operation.
xPlace the ‘ON/OFF’ switch to the ‘-’ (On position). This is on the front of the gas
valve.
xSimultaneously press and hold the (star) button and
(up arrow) button.
until a short acoustic signal confirms the start sequence
has begun; release buttons. Continuing signals confirms
the ignition is in progress. There will be a slight delay
and several sparks should be seen between the
electrode and pilot tip (See figure 9). On sensing a flame
is not present the burner unit will shut off. If there are no
sparks check the following: -
xEnsure that the electrode lead is connected to the
terminal at the base of the electrode.
xIf the above is correct, check for damage to the electrode lead.
7.4 Adjusting the remote control handset / receiver code.
If a customer has other devices that interfere with the
operation of the fire, or if more than one model 757 is
installed in the same room, it will be necessary to
adjust the remote control handset / receiver electronic
code. To do this complete the following:
xRemove the battery compartment cover from the
rear of the remote control handset.
xThere are four DIP switches located above the
battery (See figure 10). Change the DIP switch
position. Only one switch should be in the ‘ON’
position. Fit the battery compartment
cover.
xPress and hold the receiver’s reset
button (See figure 11) until you hear two
(2) acoustic signals. After the second
longer signal, release the reset button
and within the subsequent twenty (20)
seconds, press the (down arrow) on
the remote handset until you hear an
additional long acoustic signal confirming
the new code is set.
Page 19
INSTALLER GUIDE
© Baxi Heating U.K. Limited 2007.
Figure 11. Reset button
Figure 10. DIP Switches
Figure 9. Ignition operation

8. GAS SUPPLY CONNECTION
A nut and olive are provided for an 8mm pipe inlet connection to the ‘T’ connector at
the bottom front of the appliance. The ‘T’ connector can be rotated to allow a
connection from any rear-concealed connection. The ‘T’ connector includes a valve
for isolating the gas supply and a pressure test point.
The supply pipe must be rigid material. Flexible pipe must not be used.
Concealed supply pipe connection.
If a concealed connection from inside the fireplace is required then, before the
appliance is fitted into the fireplace
it will be necessary to extend the supply line so
that it will project through the hole in the back of the hotbox and run to the ‘T’
connector at the front. The pipe run from the supply line up to the rear opening in the
hotbox must be kept away from the area which will be taken by the hotbox when it is
installed. Note that the centre of the appliance inlet ‘T’ connector is 25mm above the
fireplace floor. The inlet ‘T’ connector should be fitted to the supply pipe at this stage.
9. PREPARING APPLIANCE FOR INSTALLATION
1. The fire is fitted with two transit support screws.
These are located on the sides of the hotbox and are
labelled. They prevent burner assembly movement
during transit. Remove the transit screws and discard.
2. Remove the two screws to the side of the burner
assembly (See figure 12)
3. Detach the burner assembly from the hotbox by
holding the ‘bowl’ and gently sliding forward. The
burner assembly is heavy and if not supported
sufficiently will drop when clear of its support brackets.
When sliding the burner assembly be careful not to lift
it as this may scratch the top surface.
Page 20
INSTALLER GUIDE
© Baxi Heating U.K. Limited 2007.
Figure 12. Burner module
removal