Value Point POE-8M User manual

1
POE-8M
Quick Guide
&
User’s Manual

2
Quick Guide
Step1. Connect the PoE Switch with AC power cord to 100~240VAC.
Step2. Connect the PoE AP device to LAN port 1, and your PC to LAN port
as the following connection.
Step3. Turn on the power switch, it will light on the PWR LED, and perform self-
diagnostic test. It takes about 10 seconds to complete the process.
Step4. Set your PC IP address to 192.168.2.100 (same subnet 192.168.2.x as the
web management).
Step5. Enter "192.168.2.1" (default IP address of Web management) from PC web
browser. The web management will display the following login page
Enter “admin” for user ID, “system” for password, and click the
OK button to login to the Web management.
Note: the user ID and password fields are case-sensitive.

3
Step6. Click the icon “ oE”, and then select “ oE Setting”.
Step7. Select “Enable” and click on Port No.1 and Update to power on the connected
PoE AP device for Port 1. You may also click “oE Scheduling” to select time
schedule for Power on/off scheduling control.
Step8. Refer to Chapter 4 for further networking configurations.
** Note:
roblems in setting up the web smart oE switch?
lease refer to the last chapter for troubleshooting.

4
Table of Contents
1 Introduction ........................................................................................................... 7
2 Features .................................................................................................................. 8
2.1 ower on Switch .......................................................................................... 8
2.2 LED Indicators .............................................................................................. 8
3 Switch Installations .............................................................................................. 9
3.1 ackage Contents ....................................................................................... 9
3.2 Hardware Overview ..................................................................................... 9
3.3 reparations for Site Installation ............................................................ 11
3.4 Desktop Installation .................................................................................. 12
3.5 Cabling Requirements .............................................................................. 12
3.6 ower Connection ..................................................................................... 13
3.7 Installation Steps ....................................................................................... 13
3.8 Reset to Default .......................................................................................... 15
4 Web Management ............................................................................................... 16
4.1 Setup your computer for Web management ........................................ 16
4.2 Web management ...................................................................................... 19
4.3 Administrator .............................................................................................. 20
4.3.1 Authentication Configuration ...................................................... 20
4.3.2 System I Configuration .............................................................. 21
4.3.3 System Status ................................................................................ 21
4.3.4 Load Default Setting ..................................................................... 22
4.3.5 Firmware Update............................................................................ 22
4.4 oE ............................................................................................................... 24
4.4.1 oE Setting ..................................................................................... 24
4.4.2 oE ower Delay ........................................................................... 25

5
4.4.3 oE Scheduling ............................................................................. 26
4.5 ort Management ....................................................................................... 27
4.5.1 ort Configuration ......................................................................... 27
4.5.2 ort Mirroring ................................................................................. 28
4.5.3 Bandwidth Control ........................................................................ 29
4.5.4 Broadcast Storm Control ............................................................. 35
4.6 VLAN Setting .............................................................................................. 36
4.6.1 VLAN Mode ..................................................................................... 36
4.6.2 VLAN Member ................................................................................ 37
4.7 er ort Counter ........................................................................................ 40
4.8 QoS Setting ................................................................................................. 41
4.8.1 riority Mode .................................................................................. 41
4.8.2 Class of Service Configuration ................................................... 42
4.9 Security ........................................................................................................ 44
4.9.1 MAC Address Binding .................................................................. 44
4.9.2 MAC Address Scan ....................................................................... 45
4.9.3 TC /UD Filter ............................................................................... 45
4.9.4 Web Management Filter ............................................................... 46
4.10 Spanning Tree ............................................................................................ 47
4.10.1 ST Bridge Settings ...................................................................... 47
4.10.2 ST ort Settings .......................................................................... 47
4.10.3 Loopback Detection Settings ..................................................... 48
4.11 Trunk Setting .............................................................................................. 49
4.12 DHC Relay Agent ..................................................................................... 50
4.13 NT Setting ................................................................................................. 50
4.14 Backup/Recovery ....................................................................................... 51
4.15 Miscellaneous............................................................................................. 52

6
4.16 Logout .......................................................................................................... 52
Appendix A:
roduct Specifications
....................................................................... 53
Appendix B:
Troubleshooting
.................................................................................. 55
B.1 Can NOT Access Web age? .................................................................. 55
B.2 Forget I Address, User ID, and assword?........................................ 55

7
1 Introduction
The PoE Switch is an -Port Web-Smart Passive PoE Switch with power on/off
scheduling control. The web smart features are designed to deliver high levels of
performance that are commensurate with Fast Ethernet networking, and to provide
simple and easy installation in an environment where the power over Ethernet
(PoE) are required for remote PoE devices.
The web smart switch provide 10/100Mbps Fast Ethernet connections with many
networking capabilities per port basis including Security, QoS service, Bandwidth
Control, Spanning Tree Protocol, VLAN, SNMP settings, and PoE functions.
The power over the Ethernet ports are all turned off initially, and can be turned on
per port basis through the web management to power on the corresponding
remote PoE device. The powered PoE device can be any equipment of Passive
24V DC PoE device, such as WiFi AP, IP camera, IP Phone, etc.
Each port can deliver up to 15 Watt (Max.) to the corresponding remote PoE device.
Request of more power from remote PoE device may result in a power failure due
to activation of Over-Current-Protection (OCP) circuit.
The PoE Switch can be installed in a rack mount chassis where space is limited.
The optional rack mount kit can be purchased separately from you local dealer for
rack mount installation.
The rest of this user manual will help you to uncover most of the web smart
features with step-by-step instructions illustrated on web pages.

8
2 Features
The PoE Switch is equipped with an -port RJ-45 connector for Fast Ethernet, and
the corresponding LED indicators for each port. In addition, a built-in push button is
provided for default reset, which is useful to reset back to the default IP address,
user ID, and password. The features are as the following
 RJ45 x for WAN and LAN ports with PoE capability
 Max. 15Watt per port basis
 Passive power PoE devices compatible
 Networking configurations by Web Management
 16+1 LED Indicators: LAN, PoE (for ports) + PWR (for system power)
 Built-in push button for default reset
 AC power on/off switch
 OVP, OCP, OTP protections
2.1 ower on Switch
The PoE Switch is equipped with an internal power supply to operate with 100~240
VAC, 50 ~ 60 Hz. The AC power cord connector is at the rear panel next to the
power on/off switch. Turning on the power switch, it will first perform “self-
diagnostic” test, and take about 10 seconds to complete the process.
2.2 LED Indicators
LED Status Table
LED
S
t
atus
Description
s
oE ON The PoE function is enabled.
OFF The PoE function is disabled.
ower ON System power is on.
OFF System power is off.
10/100M
ON LAN Port is in connection.
OFF No Ethernet connection.
Flashing Data is transmitting or receiving

9
3 Switch Installations
This chapter lists the package contents, and describes the hardware and detailed
procedures for installation of the web management switch. For a quick setup, please
refer to the quick guide at the beginning of this manual.
3.1 ackage Contents
Make sure that you have all the necessary accessories that come with your package,
before you start the installation of the web management switch.
After unpacking and taking out the entire package contents, please check whether
you have got the following items:
 PoE Switch Unit
 One AC Power Cord
 One CD-ROM for Quick Guide & User’s Manual
If any of these above items is missing or damaged, please contact your local dealer
for replacement.
3.2 Hardware Overview
Front anel
The ports of RJ-45 connector are on the front panel of the web smart switch with
the corresponding LED indicators. The built-in push button for default reset is next to
the PWR LED indicator, and can be easily accessed by a pencil or a ball pen.

10
LED Indicators:
LED indicators display the network connection and PoE status of the switch.
100BASE-TX Fast Ethernet with oE orts ( ort 1~8):
These ports are with passive PoE capabilities, and will supply power to the
connected PoE device under the control of the web management. This feature
allows users to freely and safely mix legacy and PoE compatible devices on their
network.
All the ports support network speeds of either 10Mbps or 100Mbps, and can
operate in half- and full- duplex transfer modes. These ports also support the
automatic MDI/MDIX crossover detection function to provide “plug and play”
capability.
Reset Button
The Reset button is used to reset all the setting back to the factory default values.
Make sure that all the settings of the switch are taken down, or all the previous
settings will be erased after pressing the “Reset” button.
The Rear anel
The 3-pronged power plug is placed at the rear panel of the switch shown as below.