VANMOOF S3 User manual

2
Your VanMoof is packed full of
features. Make the most out of them
by downloading the app.

VanMoof B.V.
Mauritskade 55 1092AD Amsterdam
Please read the manual before
riding the bike.
S3 & X3
Rider manual

The toolbox
VanMoof S3 & X3
Take your bike out of the box
Get your toolbox ready
Adjust the stem
Wheel position
Brake disc covers
Brake disc alignment
Wheel alignment
Connect the motor cable
Attach the pedals
Check your handlebar
p. 5
p.6
p. 7
p. 7
p. 8
p. 8
p. 10
p. 11
p. 12
p. 12
p. 14
p. 15
p. 17
p. 18
p. 18
p. 19
p. 20
p. 20
p. 21
p. 22
p. 23
p. 24
p. 24
p. 25
p. 32
p. 33
p. 33
p. 34
p. 35
p. 36
p.37
p. 27
p. 29
Saddle adjustment
Adjusting the handlebar height
Matrix Display
Inate your tires
Activating your bike
Handlebar buttons
Locking your bike
Unlocking when connected
Unlocking when not connected
Enabling Apple Find My
Power assist level
Controlling the lights
Power and reset
Charging
Bike basics
Chain guard and cleaning
Screw connections
Replacing parts
Apple Find My
Warranty
Warnings
Find your t Love your VanMoof
Build your VanMoof The rst ride
Table of contents

The toolbox
VanMoof S3 & X3
Take your bike out of the box
Get your toolbox ready
Adjust the stem
Wheel position
We know you can’t wait to get riding
– this won’t take long, promise.
Brake disc covers
Brake disc alignment
Wheel alignment
Connect the motor cable
Attach the pedals
Check your handlebar
Build your VanMoof

5
BUILD YOUR VANMOOF
Tire pumpCharger
Washers 2x
T 30
Allen Key #3
Allen Key #5
Cable
cover
Cellebration prop
Allen Key #6 Lube Anti-theft nut tool
Handlebar spacers
Anti-theft wrench
Anti-theft nuts 2x
The toolbox

6
BUILD YOUR VANMOOF
VanMoof X3
VanMoof S3
Charging port
Electronic shifter
Sensor
Matrix Display
Power button
Motor
Front lightRear light
Battery
Smart Cartridge
Kick Lock
Charging port
Sensor
Matrix
Display
Power button
Motor
Front light
Rear light
Battery
Smart Cartridge
Electronic shifter
Kick Lock

7
BUILD YOUR VANMOOF
1.1 To take the bike out of the box, gently
pull the yellow strap.
2.1 Take the toolbox out of the triangular
front wheel stand – you’ll nd it at the
front side of the stand. Make sure you
detach the wheel from the bike’s frame.
2.2 Remove (and recycle) all protective
packaging. Squeeze the tab on the
cable ties to remove them without
cutting – you can reuse them later.
1. Take your bike out of the box
2. Get your toolbox ready
ToolboxFront wheel stand

8
BUILD YOUR VANMOOF
90°
3.1 Rotate the stem 90° clockwise so it’s in
line with the front fender.
4.1 Take the bike out of the front wheel
stand and place it on the oor.
3. Adjust the stem
4. Wheel position
Note
See page 28 to learn how to
adjust the handlebar.
3.2 Check the bolts’ position – the top
should enter from the left, and the
bottom from the right. Tighten the two
bolts using Allen key #5, making sure
the stem stays in line with the front
wheel. Do not over-tighten the bolts,
just turn until they are secure.
Allen key #5
Place on the oor