Vaporesso GEN 200 User manual

USER
MANUAL
VAPORESSO GEN 200 & 80 S

1

1ENGLISH
ENGLISH
Thank you for choosing Vaporesso product. Please read this instruction carefully before use
to ensure a perfect experience.
If there is any additional requirement about this product, please consult the local agent or
contact us through our website: www.vaporesso.com
Drip Tip
Top Cap
Glass Tube
Air-Inlet Port
Power Button
0.96" TFT Screen
“+” Button
Mode/Conrm Button
“-” Button
Type-C USB Port
Dimensions: 140.5 x 34 x 25.5 mm
TANK Capacity: 5ml/2ml(TPD)
Coils & Suggested Wattage:
GTi 0.2Ω MESH Coil (60-75W)
GTi 0.4Ω MESH Coil (50-60W)
Battery Capacity: 1 x 18650 Battery
(Not Included)
Output Power: 5-80W
Charging Current: DC 5V/2A, Type-C
Battery Display: 0.96’’ TFT Screen
1 x VAPORESSO GEN 80 S MOD
1 x VAPORESSO iTANK (5ml/2ml TPD)
1 x GTi 0.2Ω MESH Coil (Pre-installed)
1 x GTi 0.4Ω MESH Coil (In-BOX)
1 x Extra Glass Tube
3 x O-ring
1 x Type-C Cable
1 x User Manual
1 x Warranty Card
SPECIFICATION
PACKING LIST
Drip Tip
Top Cap
Glass Tube
Air-Inlet Port
Power Button
0.96" TFT Screen
“+” Button
Mode/Conrm Button
“-” Button
Type-C USB Port
Dimensions: 138.5*44*29mm
TANK Capacity: 8ml/2ml(TPD)
Coils & Suggested Wattage:
GTi 0.2Ω MESH Coil (60-75W)
GTi 0.4Ω MESH Coil (50-60W)
Battery Capacity: 2 x 18650
Output Power: 5-220W
Charging Current: DC 5V/2A, Type-C
Battery Display: 0.96’’ TFT Screen
1 x VAPORESSO GEN 200 MOD
1 x VAPORESSO iTANK (8ml/2ml TPD)
1 x GTi 0.2Ω MESH Coil (Pre-installed)
1 x GTi 0.4Ω MESH Coil (In-BOX)
1 x Extra Glass Tube
3 x O-ring
1 x Type-C Cable
1 x User Manual
1 x Warranty Card
EXPLOADED VIEW
EXPLOADED VIEW
SPECIFICATION
PACKING LIST
VAPORESSO GEN 200
VAPORESSO GEN 80 S

32ENGLISH
1. Install the Tank
Install the tank to the battery by screwing the 510 thread. Make sure they are firmly
connected.
2. Replace the Coil
- Unscrew the thread base from the tank;
- Pull out the used coil from the tank;
- Install a new coil to the tank;
- Reattach the thread base into place.
* Refer to the gure 1.
3. Fill E-liquid
- Push the top cap according to the arrow direction;
- ll e-liquid through the hole, then lock the top cap in place after lling is nished.
- Please wait 5 minutes for the e-liquid to soak into the coil completely.
* Refer to the gure 2.
4. Adjust the Airow
To adjust the airow volume, please rotate the air-inlet ring on the bottom of the tank.
5. Power On/O the Device
Power on/o: press the power button 5 times in 2s.
6. Power Adjustment
GEN 200 & 80 S Kit is using the powerful GTi coil platform, and the suggested power need to
be noticed before start vaping.
7. Start Vaping
Press the power button to enjoy extraordinary vaping experience.
8. Charge the Battery
After connecting the Type-C cable to the battery, the battery indicator and remaining
charging time will be showed on the screen.
USER INSTRUCATIONS
GTi MESH Coils GTi 0.2Ω MESH GTi 0.4Ω MESH
Suggested Power 60-75W 50-60W
FIGURE
Figure 1: Replace the coil
Figure 3 User Interface
OPEN CLOSE
Figure 2: Fill e-liquid
Wattage
Output Voltage
Battery Level
Vaping Time
System Lock
Output Mode
Pu Counter
Resistance
Smart VW