VAS XL50-6GB User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 1
50”3-in-1 TV Console (XL50-6GB)
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if you are missing parts, do not return this
item to the Retailer Store. Please call our toll free customer service number and have your
instructions and parts list ready to provide the model name, part name or factory number:
1-866-942-5362 8:30 a.m. - 4:30 p.m. PST, Monday - Friday
ONLINE: www.whalenfurniture.com EMAIL: [email protected]
Video Instruction Guides
Go to http://whalen.showuhow.com to view step-by-step instructional
videos for assembling and installing your product. Enter the following
product number on the ShowUhow homepage.
LOT NUMBER:
DATE PURCHASED: / /
XL50-6GB

Model # XL50-6GB
Please call for replacement parts or assistance: 1-866-942-5362
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 2
QUALITY GUARANTEE
We are confident that you will be delighted with your VAS Furniture purchase.
Should this product be defective in workmanship or materials or fail under
normal use, we will repair or replace it for up to 1 year from date of purchase.
Every VAS Furniture product is designed to meet your highest expectations.
We guarantee that you will immediately see the value of our fine furniture.
This warranty gives you specific legal rights and you may also have other
rights which vary from State to State.
Customer Service: 1-866-942-5362
8:30 a.m. - 4:30 p.m. PST Monday to Friday
www.whalenfurniture.com
MANUFACTURER: VAS FURNITURE
CATALOG: 50”3-in-1 TV Console (XL50-6GB)
DATE OF MANUFACTURE: April, 2010
MADE IN CHINA
FITS UP TO MOST 56”FLAT PANEL TV’S
MAXIMUM LOAD 135 LB (61.2 kg)
MAXIMUM LOAD 50 LB (22.7 kg)
This unit is intended for use only with the products and maximum
weights indicated. Use with other products or products heavier than the maximum weights
indicated may result in instability causing possible injury. The base of the television must
be placed squarely in the center of the stand with no overhanging on either side.

Model # XL50-6GB
Please call for replacement parts or assistance: 1-866-942-5362
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 3
Parts and Hardware List for Table-top
Please read completely through the instructions and verify that all parts listed are present
before beginning assembly.
A-Top Shelf Frame (1) B- Middle Shelf Frame (1) C- Bottom Shelf Frame (1)
D1- Short Spine (1) E- Left Side Frame (1) F- Right Side Frame (1)
G- Top Glass (1) H- Glass Shelf (2)
(1) - Suction Cup (2) - 3/4” Bolt (3) - 1 1/4” Bolt (5) - Lock Washer
(24+1 extra) (20+1 extra) (14+1 extra) (34+1 extra)
(6) - Flat Washer Allen Wrench Tipping Restraint Hardware Kit (1)
(34+1 extra) (2) (Inside Plastic Bag)
Tools required: Allen Wrench (provided).

Model # XL50-6GB
Please call for replacement parts or assistance: 1-866-942-5362
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 4
Parts and Hardware List for Universal Wall Mount only
Please read completely through the instructions and verify that all parts listed are present
before beginning assembly.
J- XYZ Mounting Frame (1) K- Monitor Bracket (2) L- Safety Bar (1)
(7) - 2 1/2” Lag Bolt (8) - Large Flat Washer (9) - 1 3/4” Concrete Anchor
(6 pcs) (6 pcs) (6 pcs)
TV Mounting Kit
M4 x 12 Bolt (4) M4 x 30 Bolt (4) M5 X 12 Bolt (4) M5 x 30 Bolt (4)
M6 x12 Bolt (4) M6 x 35 Bolt (4) M8x16 Bolt (4) M8 x40 Bolt (4)
M4 Lock Washer (4) M5 Lock Washer (4) M6 Lock Washer (4) M8 Lock Washer (4)
Large Spacer (4) Small Spacer (4) M4/M5 Flat Washer (8) M6/M8 Flat Washer (4)
Note: Please keep the rest of the hardware & parts for future use.
Tools required: Phillips Screwdriver, Mallet, Power Drill, 3/16” Drill Bit, Socket wrench adapter
with socket set, 1/2” Masonry Bit for brick or concrete, Level and Stud Finder.

Model # XL50-6GB
Please call for replacement parts or assistance: 1-866-942-5362
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 5
Assembly Instructions for Table-top
Note: Please do not fully tighten all bolts until you finish assembling all parts, then go
back and fully tighten all bolts, this will make it easier during assembly of unit.
1. Unpack the unit and confirm that you have all the hardware and required parts listed.
2. Locate Short Spine (D1) on a level and protective surface with 2 round holes facing up as
shown in detail #1.
3. Align the holes on “U”bracket of three Shelf Frames (A, B & C) with the threaded inserts on
the Short Spine (D1), attach using 3/4”Bolts (2) with Washers (5 & 6) through the bracket
holes into the Spine. See detail #1.
Required hardware in this step
Description: (2) - 3/4” Bolt (5) - Lock Washer (6) - Flat Washer
Sketch
Qty. (12 pcs) (12 pcs) (12 pcs)
Tools required: Allen Wrench

Model # XL50-6GB
Please call for replacement parts or assistance: 1-866-942-5362
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 6
Assembly Instructions for Table-top
4. Stand the unit upright.
5. Pick up Left Side Frame (E) and attach to the Middle & Bottom Shelf Frame (B & C). Insert
& screw the 1 1/4” Bolts (3) with Washers (5 & 6) through the pre-drilled holes on front rail of
shelf frame and 3/4" Bolts (2) with Washers (5 & 6) through the metal bracket on the back of
shelf frame into the threaded inserts on side frame. See detail #2. DO NOT tighten the bolts.
Note: For the end metal brackets on the back of shelf frame must use only ¾” Bolt (2).
6. Proceed to attach the Left Side Frame (E) to Top Shelf Frame (A) using three 1 1/4”Bolts (3)
with Washers (5 & 6) through the pre-drilled holes in side rail. See detail #2A.
7. Repeat last two steps to install Right Side Frame (F) at the other end.
Required hardware in this step
Description: (2) - 3/4” Bolt (3) - 1 1/4" Bolt (5) - Lock Washer (6) - Flat Washer
Sketch
Qty. (8 pcs) (14 pcs) (22 pcs) (22 pcs)
Tools required: Allen Wrench

Model # XL50-6GB
Please call for replacement parts or assistance: 1-866-942-5362
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 7
Assembly Instructions for Table-top
8. Go back and tighten all bolts with Allen Wrench provided.
9. In case of uneven floor, Floor Levelers are provided at the bottom of Left & Right Side
Frame (E & F). Simply tilt the unit back and raise or lower floor leveler by hand to correct
tilting as shown in detail #3.
Parts provided Tools required
Pre-attached Floor Leveler No tool required

Model # XL50-6GB
Please call for replacement parts or assistance: 1-866-942-5362
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 8
Assembly Instructions for Table-top
10.Put the Suction Cups (1) firmly into top holes & metal tabs of three Shelf Frames (A, B & C)
as shown in detail #4.
11.Place the Top Glass (G) & Glass Shelves (H) in place as shown in detail #4. Make sure the
glass is properly centered and the black side of glass is down. Push each glass all the way
back against the Spine. Also, be sure to press down evenly and firmly each glass onto the
Suction Cups to make sure they securely rest onto the Suction Cups.
Note: Make sure that the Suction Cups go all the way into the pre-drilled holes & metal tables
to prevent the glass shelf from falling and getting damage. If glass is scratched you can
minimize the damage by using a BLACK marker and filling in scratched area from
underneath.
Required hardware in this step
Description Sketch Qty.
(1) –Suction Cup (24 pcs)

Model # XL50-6GB
Please call for replacement parts or assistance: 1-866-942-5362
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 9
Assembly Instructions for Table-top
12.Position the assembled Table-top in your desired location against the wall. Now follow the
instructions printed on the plastic bag in order to mount the Tipping Restraint Hardware Kit to
the Spine properly. As shown in detail #5.
NOTE: YOU MUST USE THIS TIPPING RESTRAINT TO ATTACH THIS UNIT TO
THE WALL, TO PREVENT ACCIDENTS AND/OR INJURIES.
13.The Table-top is ready for use now. Be sure to position your TV in center of console with no
overhang on either side.

Model # XL50-6GB
Please call for replacement parts or assistance: 1-866-942-5362
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 10
Assembly Instructions for Universal Wall Mount
Installing XYZ Mounting Frame onto WOODEN WALL
14.The XYZ Mounting Frame (J) must be mounted to two Wood Studs at least 12” apart, using a
high quality Stud Finder to locate the two adjacent studs. After you have located the studs,
verify with a nail for added security. See detail #6A.
15.Pre-drill a 2 1/2" deep hole at the desired height in each stud using a 3/16” drill bit, make sure
that the holes are centered in the studs and level with each other. Use the XYZ Mounting
Frame (J) as a template to mark the corresponding location for the bottom holes in each stud,
drill holes 2 1/2" deep with the 3/16” drill bit at the marked location.
16.Orient the Mounting Frame with the “C” rail against the wall, and using four Lag Bolts (7) with
Large Flat Washer (8) through the slots of “C” rail on Mounting Frame into the holes in the
wall, secure the mounting frame to the wall as shown in detail #6B.
Hardware provided Sketch Qty.
(7) –2 1/2” Lag Bolt (4)
(8) –Large Flat Washer (4)
Tools required
Stud Sensor, Mallet, Power Drill, 3/16” Drill Bit, Socket Set
Do not over tighten the Lag Bolts. Tighten Lag Bolts only until the Lag
Bolt Washer is pulled firmly against the “C”Plate of Mounting Frame. If there is a layer of
drywall or other material, this drywall or other material may not exceed 5/8 inch in
thickness. Failure to heed this caution may result property damage and/or personal injury.

Model # XL50-6GB
Please call for replacement parts or assistance: 1-866-942-5362
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 11
Assembly Instruction for installing XYZ Mounting Frame onto BRICK, SOLID
CONCRETE OR CONCRETE BLOCK
17.Use the XYZ Mounting Frame (J) as a template, mark six holes location on the wall, three in
the top row and three in the bottom row of slots. Make sure that the holes are level and
there is at least 6” between any two holes, pre-drill these holes with a 1/2” masonry bit to at
least 2 1/2” in depth.
18.Insert a Concrete Anchor (9) into each of these holes; make sure they are completely
seated and flush with the concrete surface, even if there is a layer of drywall or other
material in front of the concrete.
19.Attach the XYZ Mounting Frame (J) to the wall using six Lag Bolts (7) and Large Flat
Washers (8) through the slot of “C” rail on Mounting Frame into the Concrete Anchor (9) in
the wall as shown in detail #7. Make sure the back hook of Mount Frame is bottom.
Hardware provided Sketch Qty.
(7) –Lag Bolt (6)
(8) –Large Flat Washer (6)
(9) –1 3/4” Concrete Anchor (6)
Tools required: Mallet, Power Drill, 1/2” Masonry Bit for brick concrete, Socket Set
Concrete Anchors should only be used for masonry mounting.
NEVER use the wall anchors to mount the unit to drywall.
Maximum weight 165 lb (74.8 kg)

Model # XL50-6GB
Please call for replacement parts or assistance: 1-866-942-5362
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 12
Mounting Monitor Bracket to a television with a flat back
Note: For televisions with a curved back or recessed back proceed directly to step #23.
20.Determine the correct diameter of the bolt your TV requires by hand threading them into the
threaded insert on the back of the TV. If you encounter any resistance, stop immediately. If
you are unable to find the correct bolt consult a local hardware store.
21.Once you have determined the correct diameter Bolt, follow the appropriate Diagram below,
thread the Bolt through the appropriate Lock Washer, Flat Washer, the Monitor Bracket (K),
and into the TV. As shown in detail #8. Note: Lean the TV up against a wall or other solid
surface when attaching with the Monitor Brackets (K). DO NOT place the TV face down on
the glass this may cause permanent damage.
22.Make sure the Monitor Brackets (K) are centered and level with each other. Tighten the
bolts to secure the Monitor Brackets to the TV.
Parts provided Qty. Tools required
K –Monitor Bracket (2) Phillips Screwdriver
TV Mounting Kit

Model # XL50-6GB
Please call for replacement parts or assistance: 1-866-942-5362
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 13
Mounting Monitor Bracket to a television with a curved / recess back
23.Determine the correct diameter of the bolt your TV requires by hand threading them into the
threaded insert on the back of the TV. If you encounter any resistance, stop immediately. If
you are unable to find the correct bolt consult a local hardware store.
24.Once you have determined the correct diameter Bolt, follow the appropriate Diagram below,
thread the Bolt through the appropriate Lock Washer, the Large Flat Washer, the Monitor
Bracket (K), a second Large Flat Washer (M4/M5 Diameter Bolts only), appropriate Spacer
and into the threaded inserts of TV. See detail #9.
25.Make sure the Monitor Brackets (K) are vertically centered and level with each other.
Tighten the bolts to secure the Monitor Brackets to the TV.
Parts provided Qty. Tools required
K –Monitor Bracket (2) Phillips Screwdriver
TV Mounting Kit

Model # XL50-6GB
Please call for replacement parts or assistance: 1-866-942-5362
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 14
Assembly Instructions
26.Once the Monitor Brackets (K) are attached onto the back of television, ask for assistance to
lift the television up to the XYZ Mounting Frame (J). Place the hooks on Monitor Brackets
over the Mounting Frame then lower them onto the bars of Mounting Frame. Proceed to
center the television.
27.Insert the Safety Bar (L) into the bottom holes on the side of XYZ Mounting Frame (J) by
sliding it all the way across the frame. Secure the Safety Bar by rotating the bent end into
the slot of hook so that it is facing wall. Make sure it sits over the bottom hook of the Monitor
Brackets. See detail #10.
Parts provided Qty. Tools required
L - Safety Bar (1) No tool required

Model # XL50-6GB
Please call for replacement parts or assistance: 1-866-942-5362
VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 15
Assembly Instructions
28.Place assembled console under your TV
set as shown at the right.
TIPPING RESTRAINT HARDWARE
Note: We have included one Tipping Restraint Hardware bag for this unit.
When properly installed, this restraint can provide protection against the unexpected tipping of the
unit due to small tremors, bumps or climbing. We strongly recommend mounting this hardware to a
wall stud and your unit when assembling and using your console.
Please carefully read the instructions printed on the plastic bag.
Note: You must install the Tipping Restraint Hardware with the unit in use to prevent any
accidents or damage to the unit.
Tools required: Allen Wrench (provided), Phillips Screwdriver, Mallet, Power Drill, and
3/8” Drill Bit.
Your assembly should now be complete.
Thank you for your purchase.

IF YOU REQUIRED TO ORDER PARTS PLEASE USE THE LIST BELOW
50” 3-in-1 TV Console (XL50-6GB)
*XL50-6GB-1-LS Long Spine *XL50-6GB-24-M4LW M4 Lock Washer *XL50-6GB-2-TG Top Glass *XL50-6GB-25-M5LW M5 Lock Washer *XL50-6GB-3-GS Glass Shelf *XL50-6GB-26-M6LW M6 Lock Washer *XL50-6GB-4-LL Left Side Frame *XL50-6GB-27-M8LW M8 Lock Washer *XL50-6GB-5-RL Right Side Frame *XL50-6GB-28-M4x12B M4 x 12 Bolt *XL50-6GB-6-SB Swiveling Bracket *XL50-6GB-29-M4x30B M4 x 30 Bolt *XL50-6GB-7-MF Mounting Frame *XL50-6GB-30-M5x12B M5 X 12 Bolt *XL50-6GB-8-MB Monitor Bracket *XL50-6GB-31-M5x30B M5 x 30 Bolt *XL50-6GB-9-CH Complete Hardware *XL50-6GB-32-M6x12B M6 x 12 Bolt *XL50-6GB-10-3/4B 3/4” Bolt *XL50-6GB-33-M6x35B M6 x 35 Bolt *XL50-6GB-11-1 1/4B 1 1/4” Bolt *XL50-6GB-34-M8x16B M8 X 16 Bolt *XL50-6GB-12-FW Flat Washer *XL50-6GB-35-M8x40B M8 x 40 Bolt *XL50-6GB-13-LFW Large Flat Washer *XL50-6GB-36-2 1/2LB 2 1/2” Lag Bolt *XL50-6GB-14-LW Lock Washer *XL50-6GB-37-1 3/4CA 1 3/4” Concrete Anchor *XL50-6GB-15-SC Suction Cup *XL50-6GB-38-SS Short Spine *XL50-6GB-16-N Nut *XL50-6GB-39-PC Plastic Cover *XL50-6GB-17-AW Allen Wrench *XL50-6GB-40-FL Floor Leveler *XL50-6GB-18-OW Open Wrench *XL50-6GB-41-RPG Round Plastic Grommet *XL50-6GB-19-TRHK Tipping Restraint Hardware Kit *XL50-6GB-42-OPG Oval Plastic Grommet *XL50-6GB-20-LS Large Spacer *XL50-6GB-43-SB Safety Bar *XL50-6GB-21-SS Small Spacer *XL50-6GB-44-TSF Top Shelf Frame *XL50-6GB-22-M4M5FW M4/M5 Flat Washer (for TV mounting) *XL50-6GB-45-MSF Middle Shelf Frame *XL50-6GB-23-M6M8FW M6/M8 Flat Washer (for TV mounting) *XL50-6GB-46-BSF Bottom Shelf Frame