Velleman CU2200 User manual

CU2200
WIRELESS SMS ALARM MESSENGER
DRAADLOZE SMS-ALARMMELDER
SYSTÈME DE MESSAGERIE D'ALARME SMS SANS FIL
SISTEMA DE ALARMA INALÁMBRICO POR MENSAJES SMS
DRAHTLOSER SMS-ALARM
USER MANUAL 2
GEBRUIKERSHANDLEIDING 13
NOTICE D’EMPLOI 24
MANUAL DEL USUARIO 35
BEDIENUNGSANLEITUNG 46
V3_03

CU2200 v3-03
23.10.2014 ©Velleman nv
2
User manual
1. Introduction
To all residents of the European Union
Important environmental information about this product
This symbol on the device or the package indicates that disposal of the device after its lifecycle could
harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal waste; it should
be taken to a specialized company for recycling. This device should be returned to your distributor or
to a local recycling service. Respect the local environmental rules.
If in doubt, contact your local waste disposal authorities.
Thank you for buying a VELLEMAN product! The CU2200 is equipped with a very reliable Siemens 16 bit MCU and
can be used for numerous applications (except for medical and aerospace applications) such as industrial
equipment or area monitoring, data capturing, home or car security… Please read the manual thoroughly before
bringing this device into service. If the device was damaged in transit, do not install or use it and contact your
dealer.
2. Safety Instructions
Keep the device away from children and unauthorised users.
Risk of electroshock when opening the cover. Touching live wires can cause life-threatening
electroshocks. Do not open the housing yourself. Have the device repaired by qualified personnel.
There are no user-serviceable parts inside the device. Refer to an authorized dealer for service and/or
spare parts.
3. General Guidelines
Refer to the Velleman® Service and Quality Warranty on the last pages of this manual.
Dry location use only. Keep this device away form rain, moisture, splashing and dripping
liquids. Never put objects filled with liquid on top.
Keep this device away from dust and extreme temperatures.
Protect this device from shocks and abuse. Avoid brute force when operating the device.
Familiarise yourself with the functions of the device before actually using it.
All modifications of the device are forbidden for safety reasons. Damage caused by user modifications to the
device is not covered by the warranty.
Only use the device for its intended purpose. Using the device in an unauthorised way will void the warranty.
Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the
dealer will not accept responsibility for any ensuing defects or problems.
Keep this manual for future reference.
Do not use outside the technical specifications (see §12).
4. Features
8 x alarm inputs (opto-isolated)
1 x relay output
4 x programmable mobile phone numbers for alarm SMS
4 x programmable phone numbers for alarm call
3 alarm alert modes: SMS, phone dial or SMS and phone dial
automatic power supply voltage level check
automatic reporting on low-power voltage level
programmable SMS alarm text message
GSM dual band support
each event sends its own text message
remote arming or disarming
easy installation
functions: text messages, administration, input and output are all programmable through your mobile phone
access control: by password and mobile phone caller ID
advantages
ono mobile phone is needed on-site
ono alarm panel is needed on-site
ono more constant telephone line charges
ono more on-site maintenance
osecure self-contained unit

CU2200 v3-03
23.10.2014 ©Velleman nv
3
5. Overview
OUT1
Relay output jumper
1 2 3
▪▪▪
1-2 short NC
2-3 short NO (default)
POW
7~12VDC power input
GND
ground
AD1, AD2
these inputs are not supported on the CU2200
IN1, IN3, IN4,
IN5, IN6, IN7, IN8
12VDC alarm input, 7~15mA
GND
common ground opto-coupled
IN2+, IN2-
7~12VDC input
OUT1
relay output, max. 1A, 24VDC, 1A, 120VAC, NC/NO (selected by jumper on board)
Alarm Input
12VDC, 7 ~ 15m, Opto-isolated Inputs (1kΩ Input
Resistance)
24VDC, resistor 1 ~ 2,2kΩ should be used in serial
(a) IN1, IN3, IN4, IN5, IN6, IN7, IN8
Alarm Input: DC12V 7 ~ 15mA, GND: Common Ground
(b) IN2+, IN2-
IN2+:DC5 ~ 12V
IN2-: Ground [It must NOT be common to the GND of the
board]
Relay Output
OUT1, OUT2, OUT3:
Max. 1A, 24VDC / 1A, 120VAC
NC/NO (selected by jumper on board)
Note: OUT2 and OUT3 are not available
on CU2200
6. Connection
RS232 pin assignment
9600bps, 8bit, no parity, 1 stop
pin 2 RxD
pin 3 TxD
pin 5 GND

CU2200 v3-03
23.10.2014 ©Velleman nv
4
LED 1 –green status LED
Rapid flashing on/off
GSM module normal operation
Flashing on/off
GSM network connection problem
Reason:
Antenna not connected
No SIM card
Defective SIM card
Defective GSM module
LED 2 –red network LED
On
Normal operation
Flashing on/off
Searching GSM network
Connecting to network
Receiving SMS messages
Sending SMS messages
Phone dialling
Sound Monitoring
The CU2200 automatically picks up any phone call after eight rings. By connecting a microphone to the
CU2200, you will be able to hear all actions in the room.
7. Quick Setup
Press the yellow button so as to eject the card caddy. Insert
the SIM card with the contacts facing down. Press the card
back into the CU2200.
Attention: “asking for PIN code” must be deactivated
on SIM card first, before use with CU2200! (See
instructions of your mobile phone).
Connect the 12VDC power supply and wait until the red LED
turns on and the green LED flashes every few seconds.
Send following SMS message to the CU2200 (from another
mobile phone): PWD:1234,STATUS%.
Your mobile phone will receive an SMS reply within 30
seconds reporting the health status.
NOTE: The SIM card in the CU2200 must be activated by a
provider like a regular SIM card in a mobile phone.
Make sure to activate the caller ID service.
8. PC Setup Software [V7.0]
The unit can be programmed by: (A) SMS command via mobile phone
(B) Software via its built-in RS232 port
First check the hardware version of your device via an SMS from your mobile phone. When the SMS was correct
the device will reply with a text message containing the version; if there was an error you will get the message
‘SMS format is error!’. The SMS command depends on the software version:
Software version V5, V6
Software version V7
Command: PWD:XXXX,CHECKV
[SMS message received]
ex: SD41 V5.1_3_B 2008/01/28
V5 is system version or hardware version
CU2200.
Command: PWD:XXXX,CHECKVR%
[SMS message received]
ex: SD41 V7.1_3_B 2010/01/28
V7 is system version or hardware version
CU2200.
Important notes on used PC Software:
Software can be found on the included CR ROM or on the product page on www.velleman.eu.
Software version SMS_ProX.exe (SMS PRO_V5.0) only works with hardware version 5 of the CU2200.
Software version SM41DPRO.exe (SMS PRO_7.0) works with both hardware versions 6 and 7. It is
recommended to use this version when you have a hardware version 6 or 7 device.
Software version SMSPro_Setup_2.2.13_0927.exe only works with hardware version 7. When running
this software, select “basic” at start-up.
The software is developed for multiple platforms; hence it is possible that some of the shown functions
are not accessible or (fully) supported.
Note: it is not possible to upgrade the hardware version of the CU2200.
Copy the program folder to C:\ ,and run “SM41DPRO.exe” under windows.

CU2200 v3-03
23.10.2014 ©Velleman nv
5
(refer to the numbers on the illustration)
1. Select the COM port of the PC connected to the device.
2. Click [Connect] button to activate the connection between PC and SMS alarm unit.
3. Click [Health Check] or [Parameters 1 or 2(SYSTEM)] to get the internal configuration.
Please refer each setting to the corresponding command described on next pages.
9. Alarm Response Time
The messenger will start the initialization after connection to the power supply. This procedure will take
about 30 seconds.
In case of an alarm, the unit will send an SMS message to the control centre and to 4 pre-programmed
phone numbers. The control centre can be disabled in order for the phone numbers to receive the alarm
10. GSM Network Connectivity
If the GSM network is suddenly inaccessible or disconnected during the SMS sending, the message will
be lost.
When the CU2200 has failed to send the message due to an inaccessible network, the unit will search
for the network and keep sending the SMS when the network has been re-established.
When failing to send SMS messages, the CU2200 will memorize up to 10 messages and send them as
soon as the network is re-established.
11. SMS Command list
a. System setup
New Password Setup
Manual Health Reporting
Serial Number Setup
Control Centre Number & Health Reporting Schedule Setup
Power-Up Message
System Clock Setup
Phone Number Setup
b. alarm setup
Alarm Input Level & Alert Setup
SMS Alarm Message Setup
SMS Message Contents
Commanding the CU2200 to Send SMS Message
Relay Output Control
Relay Output Delay Time
Operating Voltage Low Level Alarm Message
Operating Voltage Low Level Alarm
Arm/Disarm Setup

CU2200 v3-03
23.10.2014 ©Velleman nv
6
c. System Information Report
Default Setting
System Parameters RESET
System Version Check (hardware version CU2200)
Return Message
System Parameters Report
Manual Health Report
Configure the CU2200 through the command text sent from your mobile phone. Upon reception and
processing, the unit will send a confirmation message to your mobile phone. If the command is incorrect,
the unit will reply SMS format is error!
a. System Setup
New Password Setup
Command: PWD:XXXX,NEWPWD:YYYY%
XXXX
Current password
YYYY
New password (4 digits)
Example:
PWD:1234,NEWPWD:2222%
Default password: 1234
New password: 2222
Manual Health Reporting
Command: PWD:XXXX,STATUS%
[SMS message received]
ST:XXX;T:2005/01/28/13:00;V:XXXX;A1:0000;A2:0000;K1:X;K2:X;K3:X;K4:X;K5:X;K6:X;K7:X;K8:
X;OUT1:Y;OUT2:Y;OUT3:Y;#
Example:
ST:002;T:2005/01/28/13:00;V:8.15;A1:0000;A2:0000;K1:X;K2:X;K3:X;K4:1;K5:1;K6:X;K7:X;K8
:X;OUT1:1;OUT2:1;OUT3:1;#
ST
Unit serial number
XXX
ASCII code
T
Unit internal clock
XXXX
Year/month/day/time
V
Operating voltage
XXXX
K1
Alarm channel 1
K1:0 means closed
K1:1 means open
K1 ~ 8
Alarm channel 1 ~ 8
OUT1
Relay output 1
OUT1:0 means open
OUT1:1 means closed
OUT1 ~ 3
Relay output 1 ~ 3 (outputs 2 and 3 are
displayed but not available)
Serial Number Setup
Command: PWD:XXXX,SN:YYY%
XXXX
Password
YYYY
Serial number (0-999)
Example:
PWD:1234,SN:268%
Password: 1234 (default)
Serial number set into the unit: 268 (default: 000)
Control Centre Number & Health Reporting Schedule Setup
These two values are configured by one single command.
(1) The control centre number is the phone number receiving the periodic report and regular report.
Besides the periodic report on schedule (command 5: power-up message), report of any command will
be sent to this number in addition to the mobile phone number sending the command. Maximum 2
control centres can be defined.
Command: PWD:XXXX,CTRZ:YYYYYYYYYYY,MM#%
XXXX
Password
Z
Control centre number (max. 2 centres)
1 means 1st centre number
2 means 2nd centre number
YYYYYYYYY
Phone number in control centre
MM
Period code of automatic scheduled health report
Example:
PWD:1234,CTR1:123456789,04#%
Password: 1234
Reporting health status every hour (refer to the reference table below)
(2) The periodic health report and any command from another mobile phone will be reported to the
first control centre with number 123456789.

CU2200 v3-03
23.10.2014 ©Velleman nv
7
Reference table for the automatic scheduled health report
00
No automatic report
07
Every 6 hours
01
Every 5 minutes
08
Every 12 hours
02
Every 15 minutes
09
Every day (08h00)
03
Every 30 minutes
10
Every odd day (08h00)
04
Every 1 hour
11
1st, 7th, 14th, 21st, 28th day (08h00)
05
Every 2 hours
12
1st, 15th day (08h00)
06
Every 3 hours
13
1st day of each month (08h00)
The CU2200 automatically reports the unit’s health status on a pre-defined schedule via an SMS
message.
[SMS message received]
ST:XXX;T:2006/10/08/06:15;V:XXXX;A1:0000;A2:0000;K1:X;K2:X;K3:X;K4:X;K5:X;K6:X;K7:X;K8:
X;OUT1:1;OUT2:1;OUT3:1;#
ST
Unit serial number
XXX
ASCII code
T
Unit internal clock
XXXX
Year/month/day/time
V
Operating voltage
XXXX
K1
Alarm channel 1
K1:0 means closed
K1:1 means open
K1 ~ 8
Alarm channel 1 ~ 8
OUT1
Relay output 1
OUT1:0 means open
OUT1:1 means closed
OUT1 ~ 3
Relay output 1 ~ 3
Example:
ST:001;T:2005/01/27/12:00;V:8.14;A1:2312;A2:2131;K1:1;K2:0;K3:0;K4:1; O:1#
ST
Unit serial number
001
T
Unit internal clock
Date: 27 Jan 2005, time: 12h00
V
Operating voltage
8.14VDC
K1
Alarm channel 1
1
Open
K2
Alarm channel 2
0
Closed
K3
Alarm channel 3
0
Closed
K4
Alarm channel 4
1
Open
O
Relay output 1
1
On
Power-Up Message
Whenever the unit is powered up, it will automatically send RESTART! to the control centre.
System Clock Setup
Command: PWD:XXXX,TIME:AABBCCDDEE%
XXXX
Password
AABBCCDDEE
Year/month/day/hour/minute
Example:
PWD:1234,TIME:0602031327%
Password: 1234
Clock: 3 Feb 2006, 13h27
Phone Number Setup
Command: PWD:XXXX,ALMNU1:ZZZZZZZZZZZ,2:ZZZZZZZZZZZ,3:ZZZZZZZZZZZ,4:ZZZZZZZZ
ZZZ,5:ZZZZZZZZZZZ,6:ZZZZZZZZZZZ,7:ZZZZZZZZZZZ,8:ZZZZZZZZZZZ#%
XXXX
Password
ZZZZZZZZZZZ
Phone number
Example 1:
PWD:1234,ALMNU1:12345678,2:36925814712,3:159357456,4:951753654,5:741852963,6:45678
9123,7: 369874123,8:125478963#%
Password
1234
When the alarm is triggered, an SMS message is sent to following
numbers:
N° 1
12345678
N° 2
36925814712
N° 3
159357456
N° 4
951753654
N° 5
741852963
N°6
456789123
N°7
369874123
N°8
125478963

CU2200 v3-03
23.10.2014 ©Velleman nv
8
Example 2:
PWD:1234,ALMNU1:NUL,3:NUL#%
Password
1234
With example 1, following numbers have been cancelled:
N° 1
12345678, not made
N° 2
36925814712, retained
N° 3
159357456, not made
N° 4
951753654, retained
b. Alarm Setup
Alarm Input Level & Alert Setup
Command: PWD:XXXX,ALMLEVELR:X,YY,ZZZZBBBB,NNN%
XXXX
Password
R
Alarm channel number
X
0 means disabled
1 means closed triggers alarm
2 means open triggers alarm
3 means both closed and open triggered alarm
YY
00 means alarm not reported to control centre
10 means alarm reported to control centre 1
01 means alarm reported to control centre 2
11 means alarm reported to control centre 1 and 2
ZZZZBBBB
Selection of the alarm phone dial and alarm SMS
0 means no alarm report
1 means SMS only
2 means phone dial only => (Phone dial not available)
3 means SMS first, then phone dial =>(Phone dial not available)
Z
Z
Z
Z
1st
2nd
3rd
4th phone number
B
B
B
B
5th
6th
7th
8th phone number
NNN
Relay output control
0 means no relay output control
1 means relay output triggered by alarm
N
N
N
1st
2nd
3rd relay output
(2nd and 3rd relay output not available)
Example 1:
PWD:1234,ALMLEVEL2:1,01,10000000,100%
Password
1234
Alarm channel 2
Once the input is closed, the alarm will be triggered
Control centre 2 will be reported by SMS
Phone number 1
Phone number 2
Phone number 3
Phone number 4-8
Relay output 1
Relay output 2
Relay output 3
SMS message
No report
No report
No report
Triggered “Close” by alarm
No control (not available)
No control (not available)
SMS Alarm Message Setup
Alarm channel 1 ~ 8
Command: PWD:XXXX,ALMYTEXT:□□□□□□□□□□□□#%
XXXX
Password
Y
Alarm channel number (1 ~ 8)
E
0 Close triggered alarm
1 Open triggered alarm
□□□□□□□□
SMS message (max. 130 characters –no space allowed)
Example:
PWD:1234,ALM4T1XT:Door Contact1 Open#%
Password
1234
Alarm channel 4 is triggered by “Open Contact”, SMS message “Door
Contact 1 Open” is sent to the pre-defined phone numbers.

CU2200 v3-03
23.10.2014 ©Velleman nv
9
SMS Message Contents
Command 8 is used to program the alarm message contents. The CU2200 will reply to the mobile
phone with the programmed message for that alarm channel.
Command: PWD:XXXX,READYTEXT%
XXXX
Password
Y
Alarm channel number (1 ~ 8)
Commanding the CU2200 to Send SMS Message
This command is used to make the CU2200 to send the SMS message for testing purposes.
Command: PWD:XXXX,SENDMSA:XB%
XXXX
Password
A
Phone number (1 ~ 8)
XB
SMS message selection
00: schedule health check status
01:closed triggered alarm channel 1, SMS message
02: closed triggered alarm channel 2, SMS message
03: closed triggered alarm channel 3, SMS message
04: closed triggered alarm channel 4, SMS message
05: closed triggered alarm channel 5, SMS message
06: closed triggered alarm channel 6, SMS message
07: closed triggered alarm channel 7, SMS message
08: closed triggered alarm channel 8, SMS message
09:manual input message
10:Low voltage alarm message
11:AD channel 1, SMS message
12:AD channel 2, SMS message
13:Open triggered alarm channel 1, SMS message
14: Open triggered alarm channel 2, SMS message
15: Open triggered alarm channel 3, SMS message
16: Open triggered alarm channel 4, SMS message
17: Open triggered alarm channel 5, SMS message
18: Open triggered alarm channel 6, SMS message
19: Open triggered alarm channel 7, SMS message
20: Open triggered alarm channel 8, SMS message
Example:
PWD:1234,SENDMS4:09,Good Morning%
Password
1234
SMS message “Good Morning” will be sent to phone number 4.
Error message about setting A:
Number Choice Miss A is not within 1 ~ 8
Number Non Exist No phone number is preset in that location
Error message about setting XB
Did not specify SMS contents XB is not within 00 ~20
Reply confirmation message:
Success!: CU2200 succeeds in sending message.
Failed!: Operation failed but phone number exists.
Relay Output Control
Command: PWD:XXXX,COUTN:Y%
Password
1234
N
Relay output channel (1 ~ 3) (outputs 2 and 3 not available)
Y
1
0
Turn on (close) the output
Turn off (open) the output
The relay output is N.O. by default.
Command COUTN:1 is not valid when the relay output is triggered by alarm. Reply message will be
ST:XXX in this case.
In the above case, command COUTN:0 is used to reset the relay output after the alarm is triggered.
Relay Output Delay Time
Command: PWD:XXXX,OUTNDLAY:YYYY%
XXXX
Password
N
Relay output channel (1 ~ 3) (outputs 2 and 3 not available)
YYYY
0000 –9999 seconds
0000 Turn the output on or off (default)
0005 Turn on the output for 5 seconds and off again
Turn off the output for 5 seconds and on again
The relay output delay time is good for controlling e.g. an electric door lock.

CU2200 v3-03
23.10.2014 ©Velleman nv
10
Operating Voltage Low Level Alarm Message
When the power supply voltage level is below the minimum level at 5.34VDC, the CU2200 will send
an alarm SMS message.
Date
2007-06-15
Time
13:25
ST:001;TM200706121325;V:5.34#
Operating Voltage Low Level Alarm
This command is used to set the action to be taken once the operating voltage drops below 7.0VDC.
Value of the current operating voltage can be retrieved by command 2.
Command: PWD:XXXX,ADCOUT0:YY,ZZZZBBBB,NNN%
XXXX
Password
YY
00 means alarm not reported to control centre
10 means alarm reported to control centre 1
01 means alarm reported to control centre 2
11 means alarm reported to control centre 1 and 2
ZZZZBBBB
Selection of the alarm phone dial and alarm SMS
0 means no alarm report
1 means SMS only
2 means phone dial only => (Phone dial not available)
3 means SMS first, then phone dial =>(Phone dial not available)
Z
Z
Z
Z
1st
2nd
3rd
4th phone number
B
B
B
B
5th
6th
7th
8th phone number
NNN
Relay output control
0 means no relay output control
1 means relay output triggered by alarm
N
N
N
1st
2nd
3rd relay output
(2nd and 3rd relay output not available)
Arm/Disarm Setup
Command: PWD:XXXX,ARM%
XXXX
Password
Example:
PWD:1234,ARM%
Password
1234
Unit is armed and in alert status
Command: PWD:XXXX,DISARM%
XXXX
Password
Example:
PWD:1234,DISARM%
Password
1234
Unit is disarmed and no alarm is reported
c. System Information Report
Default Setting
Command: PWD:1234,PARAMETER1%
ST:000;T:2006/10/01/01:01;H:1;F1:,00;F2;,00;XH:31#
Command: PWD:1234,PARAMETER2%
ST:000;VL:7.00,O:00,0000,000;A1M:5.000,0.000,1.000,0,5.000,0.500,O:00,00000000,000;A2M:
5.000,0.000,1.000,0,5.000,0.000,O:00,00000000,000#
Command: PWD:1234,PARAMETER3%
ST:000;K1:1,O:00,00000000,000;K2:1,O:00,00000000,000;K3:1,O:00,00000000,000;K4:1,O:00,
00000000,000;K5:1,O:00,00000000,000;K6:1,O:00,00000000,000;K7:1,O:00,00000000,000;K8:
1,O:00,00000000,000#
Command: PWD:1234,PARAMETER4%
ST:000;C1:,1;C2:,1;C3:,1;C4:,1;C5:,1;C6:,1;C7:,1;C8:,1;#
System Parameters RESET
Command: PWD:XXXX,PARAMETER&%
[SMS message received]
Parameter initialize success!